Fixes broadcast frames on the second ethernet MAC
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24723 3c298f89-4303-0410-b956-a3cf2f4a3e73
There is Secondary MAC address duplicate problem with some UBNT
RouterStation and RouterStation Pro HW batches as Primary MAC addresses
are not increased by 2 per device in board data. Fix is to use 'Locally
Administrated bit' for Secondary MAC address instead of increasing
Primary MAC addresses by 1 which could overlap with other device
Primary MAC address.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24643 3c298f89-4303-0410-b956-a3cf2f4a3e73
UBNT M-Series devices have 2 MAC addresses in board data.
Fix is to use both entries from board data instead of one entry.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24611 3c298f89-4303-0410-b956-a3cf2f4a3e73
r22700 contained a copy-and-paste error that set eth0's MAC address
twice and never set eth1's.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24036 3c298f89-4303-0410-b956-a3cf2f4a3e73
The WNDR3700's art/caldata partition contains three MAC addresses at
offsets 0, 6, and 12, used for eth0/wlan0 (shared), eth1, and wlan1,
respectively. The existing code configures eth1's MAC address by adding
1 to eth0's instead of using the value stored in the EEPROM. This patch
causes the stored value to be used directly. (On my WNDR3700s, the three
stored addresses are all sequential anyway.)
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23876 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23165 3c298f89-4303-0410-b956-a3cf2f4a3e73
LAN (eth0) is behind a switch and the fixed speed/duplex was
supposed to be for it, not WAN (eth1).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23147 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this change ath9k can handle the wireless chip on the TL-WR841N v7
board which is based on the AR7241 SoC.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23130 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23125 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add a new SPI controller driver
* add SPI driver for the CPLD chip
* convert the NAND driver
* enable the mikroSD slot
* enable more LEDs
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22863 3c298f89-4303-0410-b956-a3cf2f4a3e73
hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway
switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested
fixes#7563
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22675 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds in-flash mac-addresses and calibration data for the Senao
EAP7660D board.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22187 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Senao EAP7660D board to trunk.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21837 3c298f89-4303-0410-b956-a3cf2f4a3e73
