eliminate the asterisk from the switch port configuration and set it
automatically on the first vlan, this aligns the broadcom vlan config
with the swconfig format
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@19909 3c298f89-4303-0410-b956-a3cf2f4a3e73
Here is support for the compact Asus WL-330gE. It uses that all-in-one
5354 Broadcom chip that's also in the WL-520gU, so I assume USB
support can be soldered on. I've yet to open up the device, though.
Initial flashing is done through the CFE failsafe mode like on other
Asus devices, where you boot holding the reset button, the power LED
flashes, and you tftp an image.
Signed-off-by: David Cooper <dave@kupesoft.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@14624 3c298f89-4303-0410-b956-a3cf2f4a3e73
make mtd refresh based config append optional (leave enabled on x86)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@12657 3c298f89-4303-0410-b956-a3cf2f4a3e73
re-based against 2.4.35 and repaired for obvious breakage (didn't use
its device table, etc.).
Changes from Linksys tree:
- Remove 'vendor' and 'product' parameters; these aren't used in the
mainstream driver and seem to only have served to break it.
- Remove bogus 'sierra_device_ids' table, used with above.
- Changed references to 'sierra_device_ids' back to id_table
- Changed non-standard CONFIG_USB_SERIAL_SIERRA_3G (line 886) to
current module standard CONFIG_USB_SERIAL_SIERRAWIRELESS
- Added #include to enable pl2303 hack to remain until I can figure
out if it's still necessary.
Signed-off-by: RB <aoz.syn@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11899 3c298f89-4303-0410-b956-a3cf2f4a3e73
supported platforms (WRT54G3G) by adding direct support for the Sierra
Wireless 3G modems.
Signed-off-by: RB <aoz.syn@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11898 3c298f89-4303-0410-b956-a3cf2f4a3e73
I noticed my wrt350n would not reliably reboot after entering
the reboot command. I found this code in the source for the
wrt600n. It corrects the problem, and the wrt350n reboots
reliably now.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11470 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch allows the bcm57xx module to work correctly with failsafe mode.
insmod doesn't return an error when a module loads but doesn't detect a switch.
I added the check_module function to load the module, then make sure
it doesn't just exit immediately. This allows preinit to only attempt to
load the bcm57xx module when switch-robo and switch-adm dont detect a switch.
The activate_gpio parameter to bcm57xx simply instructs the module to attempt
to activate the switch via gpio before probing for the switch.
Tested on wrt350n.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11468 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the netconfig script to support boardtype 0x478. I've tested this
on the wrt350n, hopefully it will match the 600n as well.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11467 3c298f89-4303-0410-b956-a3cf2f4a3e73
