juhosg
302dc3a936
ar71xx: ar71xx_wdt: add shutdown handler
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29705 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-11 09:14:11 +00:00
juhosg
c63a29ee7f
ar71xx: fix sections mismatch warnings in the nand drivers
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29667 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-05 18:08:33 +00:00
juhosg
b042bd4e4d
ar71xx: ag71xx: implement get_port_{link,stats} callbacks
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29626 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-31 15:02:26 +00:00
nbd
2ca2cb6c37
ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29598 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-22 05:43:53 +00:00
juhosg
8e8e3fdde7
ar71xx: ag71xx: fix switch port setup for AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29554 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 22:25:32 +00:00
juhosg
07d1bcb923
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29553 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 22:25:30 +00:00
juhosg
cb5f456a33
ar71xx: ag71xx: setup switch interface mode on AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29552 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 22:25:29 +00:00
juhosg
f97a00297e
ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29551 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 22:25:28 +00:00
juhosg
812763d48e
ar71xx: introduce ar71xx_switch_data
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29549 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 22:25:11 +00:00
juhosg
57705b7a08
ar71xx: tplinkpart: allow to detect JFFS2 as well
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29543 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 22:03:40 +00:00
juhosg
08d268c8a7
ar71xx: ag71xx: check PHY IDs before accessing the switch registers
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29541 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 13:25:23 +00:00
juhosg
a82d9221c9
ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29540 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 13:25:21 +00:00
juhosg
ba116ade9e
ar71xx: ag71xx: nuke ar7240sw_init
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29539 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-15 13:25:20 +00:00
juhosg
35606f14a3
ar71xx: check squashfs signature in TP-Link mtd parser
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29446 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:52:33 +00:00
juhosg
17c2fb2fc8
ar71xx: add mtd partition parser for the TP-Link boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29415 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:27 +00:00
juhosg
73b96446ee
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29123 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:11 +00:00
juhosg
d9b73ec674
ar71xx: merge nand scan patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29122 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:10 +00:00
juhosg
3095cc8090
ar71xx: ag71xx: add support for getting switch port link status
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29017 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:04 +00:00
juhosg
451654dc3a
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29015 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:01 +00:00
juhosg
749767a552
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29014 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:00 +00:00
juhosg
228681e328
ar71xx: set MII interface speed from the set_speed callbacks
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29013 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:59 +00:00
juhosg
7571fae3ab
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29012 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:57 +00:00
juhosg
95d3699b73
ar71xx: ag71xx: remove MII interface setup code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:56 +00:00
juhosg
3cd36281d9
ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28977 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:16 +00:00
nbd
33f4cde7a9
ar71xx: remove dead code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28851 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:33:20 +00:00
nbd
4677737b0a
ar71xx: on ar7240, exclude ports from their own port vlan destination mask
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28850 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:33:15 +00:00
jogo
d066413d5d
ag71xx: close a race between the phy state machine and link state
...
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.
Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28380 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-08 11:37:14 +00:00
nbd
3c978d1604
ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28213 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-11 17:44:12 +00:00
nbd
db5c8f65ca
ar71xx: add some code to detect DMA stuck conditions on ar7240
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27975 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-13 22:30:14 +00:00
nbd
5051a6677f
ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27973 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-13 21:49:46 +00:00
nbd
571d12ab3a
ar71xx: fix ethernet FIFO state corruption on ar7240
...
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689 , #9405
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27896 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-04 17:36:31 +00:00
nbd
27818ae524
ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop
...
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27895 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-04 17:36:27 +00:00
nbd
3fe5c4149b
ar71xx: fix MAC/MDIO reset mask handling
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27894 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-04 17:36:23 +00:00
nbd
3bad82d2e7
ar71xx: reinitialize global switch settings after reset on ar7240
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27705 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20 14:39:47 +00:00
nbd
340551c062
ar71xx: configure address aging on ar7240
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27704 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20 14:39:42 +00:00
nbd
8ea4f149b0
ar71xx: reset the phy in the ethernet init on ar724x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27703 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20 12:04:34 +00:00
nbd
96c14099ce
ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27702 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20 12:04:29 +00:00
nbd
9dfcd7e5e2
ar71xx: increase the delay after the ethernet MAC reset
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27701 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20 12:04:25 +00:00
nbd
db4cd49d62
ar71xx: fix an unused variable warning
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27700 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-20 12:04:20 +00:00
nbd
ec8e57edd9
ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27568 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-09 06:30:13 +00:00
nbd
cc32100390
ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27567 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-09 06:29:46 +00:00
juhosg
5c047f9906
ar71xx: merge 2.6.39 patches
...
Also remove the old UART driver for ar933x.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27314 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29 08:57:37 +00:00
juhosg
da1bd2aad6
ar71xx: add 2.6.39 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27310 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-29 08:57:32 +00:00
juhosg
8738d0666a
ar71xx: cleanup AR933X UART driver
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27222 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19 13:17:51 +00:00
juhosg
63dccaf23b
ar71xx: use ar933x_uart.h in the AR933X serial driver
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27166 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-13 08:12:40 +00:00
juhosg
377e161817
ar71xx: setup wdt_clock for AR913X to avoid a kernel bug
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27102 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-04 12:30:10 +00:00
nbd
480dfda6ec
Revert "ar71xx: only enable the rx engine after the link is up..."
...
It messes up the DMA state when the link goes down
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27088 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-01 18:15:43 +00:00
juhosg
1c869e33cc
ar71xx: add serial driver for the AR933X UART
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27065 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:40 +00:00
juhosg
c7eb38661b
ar71xx: the watchdog uses the reference clock on the AR933x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27060 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:34 +00:00
juhosg
eaa759a8e5
ar71xx: Fix header offset for newer WRT160NL models
...
Newer WRT160NLs have a flash chip with 4K erase blocks instead of 64K,
resulting in miscalculated partition sizes.
Since the actual sizes did not change, hardcode them to their current
sizes, and make sure they are at least one erase block big (in case Cisco
decides to start to use chips with 128K erase blocks).
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:20 +00:00