qi-hardware/openwrt-xburst
1
0
Fork 0
mirror of git://projects.qi-hardware.com/openwrt-xburst.git synced 2024-11-28 14:48:27 +02:00
Code
21,710 Commits 13 Branches 0 Tags 117 MiB
7ea3800d31
Commit Graph

227 Commits

Author SHA1 Message Date
juhosg
451654dc3a ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29015 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-13 11:27:01 +00:00
juhosg
749767a552 ar71xx: ag71xx: remove unused mii_cfg related functions and defines 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29014 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-13 11:27:00 +00:00
juhosg
228681e328 ar71xx: set MII interface speed from the set_speed callbacks 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29013 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-13 11:26:59 +00:00
juhosg
7571fae3ab ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data 
Also rename the corresponding callback functions.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29012 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-13 11:26:57 +00:00
juhosg
95d3699b73 ar71xx: ag71xx: remove MII interface setup code 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29011 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-13 11:26:56 +00:00
juhosg
3cd36281d9 ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28977 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-12 10:54:16 +00:00
nbd
33f4cde7a9 ar71xx: remove dead code 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28851 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-08 00:33:20 +00:00
nbd
4677737b0a ar71xx: on ar7240, exclude ports from their own port vlan destination mask 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28850 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-11-08 00:33:15 +00:00
jogo
d066413d5d ag71xx: close a race between the phy state machine and link state 
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.

Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28380 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-10-08 11:37:14 +00:00
nbd
3c978d1604 ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins) 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28213 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-09-11 17:44:12 +00:00
nbd
db5c8f65ca ar71xx: add some code to detect DMA stuck conditions on ar7240 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27975 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-08-13 22:30:14 +00:00
nbd
5051a6677f ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27973 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-08-13 21:49:46 +00:00
nbd
571d12ab3a ar71xx: fix ethernet FIFO state corruption on ar7240 
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689, #9405

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27896 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-08-04 17:36:31 +00:00
nbd
27818ae524 ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop 
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27895 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-08-04 17:36:27 +00:00
nbd
3fe5c4149b ar71xx: fix MAC/MDIO reset mask handling 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27894 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-08-04 17:36:23 +00:00
nbd
3bad82d2e7 ar71xx: reinitialize global switch settings after reset on ar7240 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27705 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-20 14:39:47 +00:00
nbd
340551c062 ar71xx: configure address aging on ar7240 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27704 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-20 14:39:42 +00:00
nbd
8ea4f149b0 ar71xx: reset the phy in the ethernet init on ar724x 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27703 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-20 12:04:34 +00:00
nbd
96c14099ce ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27702 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-20 12:04:29 +00:00
nbd
9dfcd7e5e2 ar71xx: increase the delay after the ethernet MAC reset 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27701 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-20 12:04:25 +00:00
nbd
db4cd49d62 ar71xx: fix an unused variable warning 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27700 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-20 12:04:20 +00:00
nbd
ec8e57edd9 ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27568 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-09 06:30:13 +00:00
nbd
cc32100390 ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27567 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-07-09 06:29:46 +00:00
juhosg
5c047f9906 ar71xx: merge 2.6.39 patches 
Also remove the old UART driver for ar933x.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27314 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-06-29 08:57:37 +00:00
juhosg
da1bd2aad6 ar71xx: add 2.6.39 support 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27310 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-06-29 08:57:32 +00:00
juhosg
8738d0666a ar71xx: cleanup AR933X UART driver 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27222 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-06-19 13:17:51 +00:00
juhosg
63dccaf23b ar71xx: use ar933x_uart.h in the AR933X serial driver 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27166 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-06-13 08:12:40 +00:00
juhosg
377e161817 ar71xx: setup wdt_clock for AR913X to avoid a kernel bug 
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27102 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-06-04 12:30:10 +00:00
nbd
480dfda6ec Revert "ar71xx: only enable the rx engine after the link is up..." 
It messes up the DMA state when the link goes down

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27088 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-06-01 18:15:43 +00:00
juhosg
1c869e33cc ar71xx: add serial driver for the AR933X UART 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27065 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-31 22:53:40 +00:00
juhosg
c7eb38661b ar71xx: the watchdog uses the reference clock on the AR933x SoCs 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27060 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-31 22:53:34 +00:00
juhosg
eaa759a8e5 ar71xx: Fix header offset for newer WRT160NL models 
Newer WRT160NLs have a flash chip with 4K erase blocks instead of 64K,
resulting in miscalculated partition sizes.
Since the actual sizes did not change, hardcode them to their current
sizes, and make sure they are at least one erase block big (in case Cisco
decides to start to use chips with 128K erase blocks).

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27049 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-31 22:53:20 +00:00
juhosg
75e1476cce ar71xx: ag71xx: make ring sizes configurable via ethtool 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27041 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-31 22:53:10 +00:00
juhosg
a137dec884 ar71xx: ag71xx: prepare to make ring sizes configurable 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27040 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-31 22:53:09 +00:00
juhosg
940317dc35 ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define 
Reported-by: Dave Täht <dave.taht@gmail.com>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27039 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-31 22:53:07 +00:00
nbd
debcf79f90 ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo) 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27035 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-30 23:08:01 +00:00
nbd
20aef6d6fc ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27034 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-30 23:07:57 +00:00
matteo
483991c363 ar71xx: detect link on LAN ports 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26922 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-17 11:12:56 +00:00
matteo
51053e7640 use correct macros and frame size in ag71xx 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26890 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-14 23:10:06 +00:00
juhosg
bb14a2f07c ar71xx: ag71xx: make switch register access atomic 
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.

This is easily noticable during an iperf session:

...
[  3] 52.0-53.0 sec  11.3 MBytes  94.4 Mbits/sec
[  3] 53.0-54.0 sec  11.4 MBytes  95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[  3] 54.0-55.0 sec  6.75 MBytes  56.6 Mbits/sec
[  3] 55.0-56.0 sec  0.00 Bytes  0.00 bits/sec
[  3] 56.0-57.0 sec  10.5 MBytes  88.1 Mbits/sec
...
[  3] 169.0-170.0 sec  11.4 MBytes  95.4 Mbits/sec
[  3] 170.0-171.0 sec  11.4 MBytes  95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[  3] 171.0-172.0 sec  7.63 MBytes  64.0 Mbits/sec
[  3] 172.0-173.0 sec  9.38 MBytes  78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[  3] 173.0-174.0 sec  11.3 MBytes  94.4 Mbits/sec
[  3] 174.0-175.0 sec  11.4 MBytes  95.4 Mbits/sec

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26856 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-08 16:32:53 +00:00
juhosg
0511a7adf1 ar71xx: ag71xx: fix section mismatch warnings 
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.

The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26855 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-08 13:30:36 +00:00
juhosg
14088891b0 ar71xx: ag71xx: fix build error if debugfs is enabled 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26854 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-08 13:30:26 +00:00
juhosg
e5061b1935 ar71xx: ag71xx: add debugfs entry for [rt]x_ring 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26845 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-07 12:40:34 +00:00
juhosg
5155342ee7 ar71xx: ag71xx: add timestamps to ag71xx_buf 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26844 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-07 12:40:28 +00:00
juhosg
5e10b16d95 ar71xx: ag71xx: use dynamically allocated buffer for napi_stats 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26843 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-07 12:40:26 +00:00
juhosg
f6816e49d9 ar71xx: ag71xx: use debugfs_remove_recursive 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26842 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-05-07 12:40:25 +00:00
juhosg
f2a69b10a8 ar71xx: rename ar934x_ref_freq to ar71xx_ref_freq 
Also initialize that for each SoC and print its value along with the
other frequencies.

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26561 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-04-09 18:47:52 +00:00
juhosg
7072aeaf32 ar71xx: add support for the watchdog of the AR934x SoCs 
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26516 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-04-07 20:53:10 +00:00
nbd
7569a2e88f ar71xx: only allow internal access to the ar7240 switch, export the MDIO bus behind the switch instead 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26393 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-04-02 00:47:29 +00:00
nbd
fd5cb87889 ar71xx: frequent ethernet mac resets upset the MDIO bus on ar7240, so do not run them on every device open, only on tx timeouts 
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26392 3c298f89-4303-0410-b956-a3cf2f4a3e73
 2011-04-02 00:47:25 +00:00