Merge most fixes from #8677:
- add basic hardware detection of Livebox Blue 5g revisions
- register leds and gpio buttons
- fix boot address location
- properly parse mac addresses
Plus some more fixes:
- make board_livebox.c more in line with board_bcm963xx.c
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32087 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some new board definitions were added within the #ifdef CONFIG_CPU_6338
section while some other were added within #ifdef CONFIG_CPU_6345, fix this
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32060 3c298f89-4303-0410-b956-a3cf2f4a3e73
It uses spi_register_board_info() from linux/spi/spi.h but does not include it
explicitely.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32058 3c298f89-4303-0410-b956-a3cf2f4a3e73
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32004 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add led devices for D-Link DIR-300-B1 WAN LED.
Note that the GPIO state is also ANDed with the esw switch port 4
LED state, which is why I've set the amber LED to default-on.
Closes: https://dev.openwrt.org/ticket/11326
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
[ juhosg:
- fix comment style in mach-dir-300-revb.c,
- remove the PPP specific LED setup, not everyone uses a PPP connection
on the WAN interface]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31989 3c298f89-4303-0410-b956-a3cf2f4a3e73
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31910 3c298f89-4303-0410-b956-a3cf2f4a3e73
moves the linux partition, removes the config partition and the
buttons settings have small adjustments.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31909 3c298f89-4303-0410-b956-a3cf2f4a3e73