This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29973 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29972 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29914 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29912 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29905 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29904 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reading from the flash chip on the TL-WR2543ND seems buggy.
If the SPI flash driver tries to read too much data in one
SPI transfer, the flash chip returns bogus values. This can
be caused by a buggy flash chip on my board, or it can
be a bug in our SPI driver.
Add a workaround to the m25p80 driver until I find out the
root cause of the problem. The patch allows to specify the
maximum numner of bytes which can be read safely withint
one SPI transfer.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29679 3c298f89-4303-0410-b956-a3cf2f4a3e73
