It was originally tristate, but was changed to bool to prevent a build
breakage in an earlier patch revision (for a new syscall). The actual
commit[1] changed it in a way this isn't needed anymore, but
accidentially left the EXPORTFS change in. There's no reason for it
not being buildable as a module, so changing it back to tristate is
fine.
see: https://patchwork.kernel.org/patch/812832/
Thank you Jonas Gorski for the patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27011 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Add missing config symbols
* Update package/kernel for 2.6.39
CONFIG_BT_L2CAP=y and CONFIG_BT_SCO=y are set to build them into the bluetooth module.
Thank you Jonas Gorski for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27010 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add md5sum for kernel
* add some missing config symbols
* add some ssb patches to make compat-wireless compile
Thank you Peter Wagner for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27009 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes for the following warnings:
drivers/mtd/devices/block2mtd.c: In function '_open_bdev':
drivers/mtd/devices/block2mtd.c:272:3: warning: ISO C90 forbids mixed declarations and code
drivers/mtd/devices/block2mtd.c: In function 'add_device':
drivers/mtd/devices/block2mtd.c:399:13: warning: assignment discards qualifiers from pointer target type
In the case of 442-block2mtd_probe.patch, it's not until the insertion of a executable statement before the definition that causes a warning, so I've chosen to resolve the issue here by splitting the definition and the initialization into a definition and a statement (and assignment) instead.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27007 3c298f89-4303-0410-b956-a3cf2f4a3e73
The flash driver code should be cleaned up and the broad detection code should be placed into arch code and used here.
This fixes#9323
Thank you Will Holmes for the patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27005 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a missing dependency to kmod-crypto-iv. chainiv.ko and eseqiv.ko
from kmod-crypto-iv depend on crypto_blkcipher.ko from
kmod-crypto-manager.
Signed-off-by: Lars Hjersted <lars@hjersted.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26984 3c298f89-4303-0410-b956-a3cf2f4a3e73
The attached patch for dnsmasq.init allows to assign a hostname to a
particular mac-address. It's useful to override the client supplied
hostname, especially if the client does not supply a hostname at all.
It corresponds to the following example in dnsmasq.conf.example:
# Always set the name of the host with hardware address
# 11:22:33:44:55:66 to be "fred"
#dhcp-host=11:22:33:44:55:66,fred
Regards
Mathias
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26983 3c298f89-4303-0410-b956-a3cf2f4a3e73
Otherwise cmake programs try to link with host ld.so
Signed-off-by: Jan Willies <jan@willies.info>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26963 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for D-Link's DVA-G3810BN/TL product.
Signed-off-by: Roman Dumycz <roman@secureas.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26956 3c298f89-4303-0410-b956-a3cf2f4a3e73
broadcom-wl driver bound to ssb device with ssb driver probe
have osh handle struct pdev pointer value initialized with
ssb_device pointer. Later on pdev is used with legacy pci
dma api as pci_dev thus causing oops sometimes.
The patch replaces legacy pci dma api and pass relevant
device struct pointer to avoid crashes.
Signed-off-by: George Kashperko <george@znau.edu.ua>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26949 3c298f89-4303-0410-b956-a3cf2f4a3e73
It was causing an occasional kernel oops.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26948 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi,
the attached patch makes ipcalc.sh accept IP/Netmask combinations in
CIDR notation. Before you could only do:
# sh ipcalc.sh 192.168.0.0 255.255.255.0 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
with this patch you can also execute it with:
sh ipcalc.sh 192.168.0.0/24 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
The patch is based on #1260 [1], i just changed one line to calculate
the START end END ips right. I wonder why that never got included. If
there is no reason not to do i would like to ask you to commit that
patch, because its a functionality i (and probably others) miss quite often.
Btw, i also fixed 4 useless tabs, that might look a bit strange in the
patch.
Regards, Manuel
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26930 3c298f89-4303-0410-b956-a3cf2f4a3e73
* adds support for Artec Thincan
Signed-of-By: Lauri Võsandi <lauri.vosandi@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26919 3c298f89-4303-0410-b956-a3cf2f4a3e73
