Fixes for the solos-pci driver.
- Corrects calculation of headroom for padding.
- Removes pointless debug messages.
- Expose Bis A and Bis M annex capabilities.
- Expose hardware revision.
Signed-off-by: Philip Prindeville <philipp_subx@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30541 3c298f89-4303-0410-b956-a3cf2f4a3e73
Submitted upstream to netdev by Chas Williams on linux-atm.
Signed-off-by: Philip Prindeville <philipp_subx@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30540 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a new wireless config parameter short_preamble=0|1 to enable
usage of short preambles. Default is to only allow long preambles
as before.
Even if short_preamble is set to 1 hostapd will take care that
short preambles are disabled as soon as a STA associates that
cannot handle short preambles.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30539 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for a kernel module package for SLIP. We needed it forusing tunslip6 from Contiki OS for 6LoWPAN communications.
Signed-off-by: Markus Becker <mab@comnets.uni-bremen.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30538 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30537 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update e2fsprogs to the last upstream version 1.42.
blkid works fine without 100_add_missing_libpthread_for_blkid.patch.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30535 3c298f89-4303-0410-b956-a3cf2f4a3e73
While the disadvantage is less available flash space, it's easy and
safe to flash without opening the device.
Going back to the original firmware is also possible.
This patch add two firmware utilities, mkbrncmdline and mkbrnboot.
mkbrncmdline patches the uncompressed kernel so the registeres a0 to
a3 are initialized and the memory size is passed in.
mkbrnboot takes the lzma compressed kernel and squashfs images and
creates a firmware image that can be flashed using the BRN-BOOT
recovery kernel, which is booted by holding both buttons when
powering up the device and will listen on http://192.168.2.1.
The firmware file from bin/lantiq/ to use is
openwrt-lantiq-danube-ARV4525PW-BRNDTW502-brnImage
The BRN-BOOT recovery kernel does size-check the image, so if it's
too big to fit into flash it will complain accordingly.
A second patch is needed to make the wired network interface work
since there is no u-boot to pre-initialise it.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30532 3c298f89-4303-0410-b956-a3cf2f4a3e73
We want the `_start's symbols to be at the very beginning of the `stage2'
binary's `.text' section. However, nothing enforces this requirement. With
recent binutils (ie. post 2.19.1), this results in a corrupt binary, as ld(1)
puts another symbol (eg. `journal_init') at the beginning of the section.
Fix this by providing a stripped down version of the default linker script
where we enforces the position of `_start' in the `.text' section.
Patch by Arnaud Lacombe (#10444)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30484 3c298f89-4303-0410-b956-a3cf2f4a3e73
