This patch adds the option to enable jumbo frames on the rtl8366s
switch. This is almost exactly the same as the first patch at
https://dev.openwrt.org/ticket/7977 and it has been requested
in a comment there.
I have tested this and it successfully allows devices on the switch
using jumbo frames to communicate.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28267 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Ed Wildgoose's alix platform driver plus my
enhancement to add GPIO soft button support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28081 3c298f89-4303-0410-b956-a3cf2f4a3e73
on some platforms, erase suspend leads to data corruption and lockups when write
ops collide with erase ops. this has been observed on the buffalo wzr-hp-g300nh.
rather than play whack-a-mole with a hard to reproduce issue on a variety of devices,
simply disable erase suspend, as it will usually not produce any useful gain on
the small filesystems used on embedded hardware.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27984 3c298f89-4303-0410-b956-a3cf2f4a3e73
KanjiMonster did the right patch, I was just confused because of linux-3.0 and linux-2.6.30
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27954 3c298f89-4303-0410-b956-a3cf2f4a3e73
find_task_by_vpid is already exported by the kernel without any patches needed.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27953 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is breaking some devices out there such as Winchiphead CH341 adapters (#9601)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27885 3c298f89-4303-0410-b956-a3cf2f4a3e73
The old ieee1394 stack was removed in 2.6.37. The new firewire stack is
available for all kernel versions, but experimental for the older one, so
make both available where appropriate.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27874 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also make switches available under a generic name "switch<num>" for device
name agnostic access. The old device name is used as an alias for backward
compatibility.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27800 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some config symbols for kernel 3.0.
Thank you realopty for the patch.
This is from #9719.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27775 3c298f89-4303-0410-b956-a3cf2f4a3e73
Issue map read after Write Buffer Load command to ensure chip is ready
to receive data.
Signed-off-by: George Kashperko <george@znau.edu.ua>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27760 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes problem with TFM allocation in cryptosoft.c
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Hauke:
* remove ubsec_ssb package and take it from ocf-linux
* use patches from ocf-linux package
* refresh all patches
* readd some build fixes for OpenWrt.
* readd CRYPTO_MANAGER dependency
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27753 3c298f89-4303-0410-b956-a3cf2f4a3e73
jow
jogo
cshore
acoul
juhosg
kaloz
florian
hauke
nbd