Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
(the GPIODEV code has been removed, the sysfs interface
can be used to control the GPIO lines instead - juhosg)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23165 3c298f89-4303-0410-b956-a3cf2f4a3e73
LAN (eth0) is behind a switch and the fixed speed/duplex was
supposed to be for it, not WAN (eth1).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23147 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this change ath9k can handle the wireless chip on the TL-WR841N v7
board which is based on the AR7241 SoC.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23130 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is still preliminary and not really tested much. Anyway, this
version seems to be enough to get both wired and wireless
interfaces working. Buttons and leds are also working.
mach-ap96.c is based on mach-wndr3700.c.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23125 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add a new SPI controller driver
* add SPI driver for the CPLD chip
* convert the NAND driver
* enable the mikroSD slot
* enable more LEDs
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22863 3c298f89-4303-0410-b956-a3cf2f4a3e73
hooks directly into the ethernet driver, as MAC resets also require switch reinitializations and the switch is part of the cpu core anyway
switch only tl-wr741nd (and other devices using this board file, such as tl-wr841nd) over to using this by default, as other devices are still untested
fixes#7563
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22675 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds in-flash mac-addresses and calibration data for the Senao
EAP7660D board.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22187 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Senao EAP7660D board to trunk.
Signed-off-by: Daniel Golle <daniel.golle@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21837 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the NBG460N/550N/550NH mtd partitions.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21443 3c298f89-4303-0410-b956-a3cf2f4a3e73
when we receive a pci/ahb interrupt, we need to flush pending data for dma
from the device, otherwise the tx path may get stuck if the completion flag
of the dma descriptor is not updated at the time the tx interrupt arrives.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21143 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the zyxel nbg460n/550n/550nh routers.
Currently this only works if a second stage bootloader is also flashed,
as the used switch needs extra initialization.
Signed-off-by: Michael Kurz <michi.kurz@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20990 3c298f89-4303-0410-b956-a3cf2f4a3e73
- on ar724x, rx buffers can be aligned with an offset of 2, which keeps the ip header aligned
- alignment offset is only added if the ar8216 workaround is not active and the phy driver does not advertise its own packet alignment
- ar71xx and ar91xx can not handle rx alignment offsets, however taking a hit on unaligned exceptions seems to have less overhead than re-aligning the data for large packets
- use memmove to re-align small packets, if necessary
tested on ar9132, ar7240 and ar7242 based devices without ar8216 headers
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20892 3c298f89-4303-0410-b956-a3cf2f4a3e73
This avoids probing of the AR8216 chip on the eth0 interface.
Cc: backfire@openwrt.org
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20754 3c298f89-4303-0410-b956-a3cf2f4a3e73
