mirror of
git://projects.qi-hardware.com/wernermisc.git
synced 2024-11-24 23:37:31 +02:00
68 lines
2.6 KiB
Plaintext
68 lines
2.6 KiB
Plaintext
M1pre-rc4 vs. shorted USB
|
|
=========================
|
|
|
|
These are the results of supplying an M1 equipped with a
|
|
current-limiting power switch from a lab supply and shorting or
|
|
(over)loading one USB port. Note that this test involved only
|
|
resistive loads.
|
|
|
|
Source Input J21/J3 Boot Short USB Load USB (2 Ohm)
|
|
------- --------------- --------------- ------- --------------- ---------------
|
|
4.50 - - No - -
|
|
4.60 4.41/4.46/4.50 4.03/4.20/4.33 Unstbl. Reset 4.04/4.09/4.33
|
|
4.70 4.51/4.57/4.60 4.15/4.31/4.43 Unstbl. Reset 4.16/4.22/4.43
|
|
4.80 4.61/4.66/4.70 4.22/4.40/4.52 Yes Reset 4.25/4.32/4.53
|
|
4.90 4.71/4.76/4.80 4.29/4.47/4.60 Yes Reset 4.39/4.46/4.62
|
|
5.00 * 4.81/4.86/4.90 4.47/4.62/4.72 Yes Reset [1,2] 4.48/4.55/4.72
|
|
5.10 - - Yes Reset - [3]
|
|
5.20 - - Yes Reset -
|
|
5.30 5.10/5.16/5.19 4.61/4.86/4.99 Yes Unstbl. -
|
|
5.40 - 4.85/5.01/5.10 Yes 4.89/5.01/5.11 [4] -
|
|
|
|
* Voltage at source: 4.99/5.01/5.01 V
|
|
|
|
- not measure either because measurement was not applicable or
|
|
because the result would have been of limited interest.
|
|
|
|
All voltage measurements min/avg/max, over 3000 samples. Flickernose
|
|
was rendering "The Tunnel" at the time. The M1pre-rc4 was running
|
|
the vanilla 2011-07-13 installation.
|
|
|
|
"Source" is the nominal supply voltage, from a Leaptronix mPP-3040D,
|
|
with current limit set to 3.0 A.
|
|
|
|
"Input" is the voltage measured on the supply cables near the M1's
|
|
DC input.
|
|
|
|
"J21/J3" is the voltage on the internal 5 V rail measured across
|
|
J21.1 and J3.14, with a Fluke 8845A with averaging set to 1 PLC.
|
|
[5] shows the measurement configuration.
|
|
|
|
"Boot" indicates whether the M1 can boot out of standby with the
|
|
respective voltage and current limit. If only unstable operation
|
|
was achieved, M1 only sometimes booted or reset after running for
|
|
some minutes.
|
|
|
|
"Short USB" indicates what happens if one USB port is shorted
|
|
through labsw. In all most, the voltage drop on the 5 V rail was
|
|
sufficiently large to cause a reset. [1] and [2] show the internal
|
|
5 V rail in channel 1, and the external VBUS on channel 2. Note
|
|
that the resistive probes used have a few percent of linear error.
|
|
[6] shows the external setup on the USB port.
|
|
|
|
If setting a supply voltage well above the nominal 5.0 V, even
|
|
shorts on USB can be survived. At 5.30 V and 5.40 V, resets still
|
|
occurred frequently. [4] shows the 5 V rail (barely) escaping a
|
|
reset.
|
|
|
|
"Load USB (2 Ohm)" repeats the same experiment with a 2 Ohm series
|
|
resistor added. [3] shows the response. Occasional resets occurred
|
|
at nominal voltages of 4.80 V or below.
|
|
|
|
[1] usb-short-100us.png
|
|
[2] usb-short-10us.png
|
|
[3] usb-2R-200us.png
|
|
[4] usb-short-5V4.png
|
|
[5] tap-j21j3.jpg
|
|
[6] tap-usb.jpg
|