- atusd.brd: rotated crystal by 90 degrees
- atusd.brd: increased density of digital signal lines by making them "hug"
each other
- atusd.brd: reduced board length by 1.4 mm
- atusd.brd: chamfered upper left corner
- atusd.brd: removed "8:10 CARD" to make room for more important text
- atusd.brd: added "CC-BY-SA"
- atusd.brd: added silk screen text: "802.15.4", "qi-hw.com", "CC-BY-SA",
and "by Werner Almesberger"
- atusd.brd: updated version to 20110116
- lib/atusd.c: renamed CLK to SLP_TR
- lib/atusd.c (atusd_cycle, atusd_cycle, atusd_open, atusd_close):
#ifdef'ed all uses of CLK and changed them to SLP_TR (along with the
change in function)
- atrf-txrx/atrf-txrx.c (init_txrx): always use the crystal oscillator
Known bug: didn't connect SLP_TR.
- atusd.sch, atusd.brd: replaced external clock with crystal
- atusd.sch, atusd.brd: increased version number to 20110115
- atusd.brd: changed "ATUSD" text on PCB to "8:10 CARD"
According to the data sheet, it has to be enabled. The Software Model
doesn't mention it. Experiments show that it's indeed useless and just
adds noise.
- atrf-txrx.c (usage, main): added option -C mhz to enable the CLKM output
and to set its frequency
- atrf-txrx.c (init_txrx): if requested, enable CLKM and set to maximum
drive strength
- atusd.sch (R1): removed useless 0R resistor in clock path
- atusd.sch (R2): renamed to R1
- atusd.cmp, atusd.brd: updated for above resistor change
- atusd.sch, atusd.brd: set version number to 20110109
- atrf-txrx.c (init_txrx): unmask all interrupts for 231 compatibilit,
where masked interrupts are now indicated in IRQ_STATUS
- atrf-txrx.c (init_txrx): on the 231, wait for (and clear) the CCA_ED_DONE
interrupt when entering TRX_OFF after reset
- tools/Makefile (upload): make destinastion host name ("ben" or "jlime")
depend on TARGET
- tools/Makefile.common (CC_ben, CFLAGS_ben, LDLIBS_ben, MACROS_ben):
renamed to *_openwrt and added *_jlime equivalents
- tools/atrf-rssi/Makefile: added settings to use SDL_gfx on Jlime
- tools/lib/Makefile (OBJS_ben): renamed to OBJS_ben_openwrt and added
OBJS_ben_jlime
- atrf-txrx.c (test_mode): moved test mode setup to enter_test_mode_230
- atrf-txrx.c (enter_test_mode_231): enter test mode on AT86RF231 (untested)
- atrf-txrx.c (test_mode): reset AT86RF231 register 0x1c when leaving
- at86rf230.h (REG_BATMON): address is 0x11, not 0x10
- at86rf230.h (TRX_CMD_MASK): width is 5 bits, not 3
- at86rf230.h (CLKM_CTRL_MASK): width is 3 bits, not 2
- at86rf230.h (PA_EXT_EN, IRQ_2_EXT_EN, TX_AUTO_CRC_ON_231): shifted by one
bit
- at86rf230.h (RX_BL_CTRL, AACK_DIS_ACK): added missing field
- at86rf230.h: added fields PA_BUF_LT and PA_LT
- at86rf230.h (ANT_DIV): added fields of this register
- at86rf230.h (NATMON_VTH_SHIFT, NATMON_VTH_MASK): corrected typo
- atrf-txrx.c (tx_pwr, tx_pwr_230, tx_pwr_231, set_power): table of power
values depends on chip
- atrf-txrx.c (set_power): location of TX_AUTO_CRC_ON and use of
REG_PHY_TX_PWR depends on chip
- tools/lib/atrf.h, tools/lib/atrf.c (atrf_identify): added chip
identification function to library
- tools/atrf-id/atrf-id.c (show_info): print information returned by
atrf_identify
- tools/atrf-id/atrf-id.c (show_info): decode JEDEC manufacturer ID
- atusd.brd: moved antenna by 20 mil to make more room for vias
- atusd.brd: increased RF via density to up to 50-60 mil per via
- atusd.brd: increased zone clearance to 10 mil, to make board easier to
solder
- atusd.pro: changed ../components/at86rf230 to ../components/at86rf231
- atusd.sch (U1): set to AT86RF231
- atusd.sch: moved clock input from pin 29 to pin 28 (still XTAL1)
- atusd.sch: changed version to 20110104
- atrf.sch: replaced the AT86RF230 with the AT86RF231
- atusb.sch, usb.sch, atrf.sch: removed TST signal
- atrf.sch: grounded former TST pin
- atusb.brd: updated for TST removal
- atusb.brd: increased space between SLP_TR and nRST_RF vias
- atusb.brd: connect U2 pin 6 to ground pad
- atusb.sch, usb.sch, atrf.sch, atusb.brd: changed version to 20110104
- BOOKSHELF (at86rf231): the AT86RF231, successor of the AT86RF230
- BOOKSHELF (avt2027, aes): the AT86RF231's AES module
- BOOKSHELF: moved the aliases "transceiver", "txrx", and "atrf" from the
AT86RF230 to the AT86RF231
- BOOKSHELF: added aliases "rf230" and "rf231" for the transceivers
- bom/atrf.equ, bom/dk/digi-key.equ: added the AT86RF231(-ZU)
