iris/mips/nanonote/jz4740.hhp

#pypp 0
// Iris: micro-kernel for a capability-based operating system.
// nanonote/jz4740.ccp: Chip features.  Most of this file is
// 	copied from the Linux source files include/asm-mips/jz4740/{ops,regs}.h,
// 	which don't have a copyright statement or license in the header.
// Copyright 2009 Bas Wijnen <wijnen@debian.org>
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program.  If not, see <http://www.gnu.org/licenses/>.

#ifndef __JZ4740_HH__
#define __JZ4740_HH__

// Main clock, for cpu, serial port, and with divisors for most other hardware
#define JZ_EXTAL	12000000   /* 12 MHz */
// RTC clock
#define RTC_CLOCK	32768     /* 32.768 KHz */
// Interrupt source used for system timer
#define TIMER_INTERRUPT	IRQ_TCU0

// Physical addresses are where they really are.
#define	CPM_PHYSICAL	0x10000000
#define	INTC_PHYSICAL	0x10001000
#define	TCU_PHYSICAL	0x10002000
#define	WDT_PHYSICAL	0x10002000
#define	RTC_PHYSICAL	0x10003000
#define	GPIO_PHYSICAL	0x10010000
#define	AIC_PHYSICAL	0x10020000
#define	MSC_PHYSICAL	0x10021000
#define	UART0_PHYSICAL	0x10030000
#define	I2C_PHYSICAL	0x10042000
#define	SSI_PHYSICAL	0x10043000
#define	SADC_PHYSICAL	0x10070000
#define	EMC_PHYSICAL	0x13010000
#define	DMAC_PHYSICAL	0x13020000
#define	UHC_PHYSICAL	0x13030000
#define	UDC_PHYSICAL	0x13040000
#define	LCD_PHYSICAL	0x13050000
#define	SLCD_PHYSICAL	0x13050000
#define	CIM_PHYSICAL	0x13060000
#define	ETH_PHYSICAL	0x13100000

#ifdef __KERNEL__
// In kernel space you need to add 0xa0000000 to see them unmapped uncached in kseg2.
#define	CPM_BASE	(0xa0000000 + CPM_PHYSICAL)
#define	INTC_BASE	(0xa0000000 + INTC_PHYSICAL)
#define	TCU_BASE	(0xa0000000 + TCU_PHYSICAL)
#define	WDT_BASE	(0xa0000000 + WDT_PHYSICAL)
#define	RTC_BASE	(0xa0000000 + RTC_PHYSICAL)
#define	GPIO_BASE	(0xa0000000 + GPIO_PHYSICAL)
#define	AIC_BASE	(0xa0000000 + AIC_PHYSICAL)
#define	MSC_BASE	(0xa0000000 + MSC_PHYSICAL)
#define	UART0_BASE	(0xa0000000 + UART0_PHYSICAL)
#define	I2C_BASE	(0xa0000000 + I2C_PHYSICAL)
#define	SSI_BASE	(0xa0000000 + SSI_PHYSICAL)
#define	SADC_BASE	(0xa0000000 + SADC_PHYSICAL)
#define	EMC_BASE	(0xa0000000 + EMC_PHYSICAL)
#define	DMAC_BASE	(0xa0000000 + DMAC_PHYSICAL)
#define	UHC_BASE	(0xa0000000 + UHC_PHYSICAL)
#define	UDC_BASE	(0xa0000000 + UDC_PHYSICAL)
#define	LCD_BASE	(0xa0000000 + LCD_PHYSICAL)
#define	SLCD_BASE	(0xa0000000 + SLCD_PHYSICAL)
#define	CIM_BASE	(0xa0000000 + CIM_PHYSICAL)
#define	ETH_BASE	(0xa0000000 + ETH_PHYSICAL)

// udelay should not be called from the kernel.
#define udelay(x) dpanic (x, "udelay called")

#else
// In user space, they just need a mapping.
#define	UNMAPPED_BASE	0x00000000

#define	CPM_BASE	0x00001000
#define	INTC_BASE	0x00002000
#define	TCU_BASE	0x00003000
#define	WDT_BASE	0x00004000
#define	RTC_BASE	0x00005000
#define	GPIO_BASE	0x00006000
#define	AIC_BASE	0x00007000
#define	MSC_BASE	0x00008000
#define	UART0_BASE	0x00009000
#define	I2C_BASE	0x0000a000
#define	SSI_BASE	0x0000b000
#define	SADC_BASE	0x0000c000
#define	EMC_BASE	0x0000d000
#define	DMAC_BASE	0x0000e000
#define	UHC_BASE	0x0000f000
#define	UDC_BASE	0x00010000
#define	LCD_BASE	0x00011000
#define	SLCD_BASE	0x00012000
#define	CIM_BASE	0x00013000
#define	ETH_BASE	0x00014000

// Default lcd framebuffer mapping space.
#define LCD_FRAMEBUFFER_BASE ((unsigned *)0x00015000)

// Map IO memory (requires a priviledged Iris::my_thread capability).
#include <iris.hh>
static void __map_io (unsigned physical, unsigned mapping):
	Iris::Page p = Iris::my_memory.create_page ()
	// false means not cachable; false means don't free when done.
	p.alloc_physical (physical, false, false)
	Iris::my_memory.map (p, mapping)
	Iris::free_cap (p)

#define	map_cpm() do { __map_io (CPM_PHYSICAL, CPM_BASE); } while (0)
#define	map_intc() do { __map_io (INTC_PHYSICAL, INTC_BASE); } while (0)
#define	map_tcu() do { __map_io (TCU_PHYSICAL, TCU_BASE); } while (0)
#define	map_wdt() do { __map_io (WDT_PHYSICAL, WDT_BASE); } while (0)
#define	map_rtc() do { __map_io (RTC_PHYSICAL, RTC_BASE); } while (0)
#define	map_gpio() do { __map_io (GPIO_PHYSICAL, GPIO_BASE); } while (0)
#define	map_aic() do { __map_io (AIC_PHYSICAL, AIC_BASE); } while (0)
#define	map_msc() do { __map_io (MSC_PHYSICAL, MSC_BASE); } while (0)
#define	map_uart0() do { __map_io (UART0_PHYSICAL, UART0_BASE); } while (0)
#define	map_i2c() do { __map_io (I2C_PHYSICAL, I2C_BASE); } while (0)
#define	map_ssi() do { __map_io (SSI_PHYSICAL, SSI_BASE); } while (0)
#define	map_sadc() do { __map_io (SADC_PHYSICAL, SADC_BASE); } while (0)
#define	map_emc() do { __map_io (EMC_PHYSICAL, EMC_BASE); } while (0)
#define	map_dmac() do { __map_io (DMAC_PHYSICAL, DMAC_BASE); } while (0)
#define	map_uhc() do { __map_io (UHC_PHYSICAL, UHC_BASE); } while (0)
#define	map_udc() do { __map_io (UDC_PHYSICAL, UDC_BASE); } while (0)
#define	map_lcd() do { __map_io (LCD_PHYSICAL, LCD_BASE); } while (0)
#define	map_slcd() do { __map_io (SLCD_PHYSICAL, SLCD_BASE); } while (0)
#define	map_cim() do { __map_io (CIM_PHYSICAL, CIM_BASE); } while (0)
#define	map_eth() do { __map_io (ETH_PHYSICAL, ETH_BASE); } while (0)

// udelay implementation
void cdelay (unsigned cs):
	Iris::my_receiver.set_alarm (cs + 1)
	Iris::Cap ().call ()

#endif

#define REG8(x) (*(volatile unsigned char *)(x))
#define REG16(x) (*(volatile unsigned short *)(x))
#define REG32(x) (*(volatile unsigned *)(x))

//************************************************************************
// INTC (Interrupt Controller)
//************************************************************************
#define INTC_ISR	REG32 (INTC_BASE + 0x00)
#define INTC_IMR	REG32 (INTC_BASE + 0x04)
#define INTC_IMSR	REG32 (INTC_BASE + 0x08)
#define INTC_IMCR	REG32 (INTC_BASE + 0x0c)
#define INTC_IPR	REG32 (INTC_BASE + 0x10)

#define IRQ_I2C		1
#define IRQ_UHC		3
#define IRQ_UART0	9
#define IRQ_SADC	12
#define IRQ_MSC		14
#define IRQ_RTC		15
#define IRQ_SSI		16
#define IRQ_CIM		17
#define IRQ_AIC		18
#define IRQ_DMAC	20
#define IRQ_TCU2	21
#define IRQ_TCU1	22
#define IRQ_TCU0	23
#define IRQ_UDC 	24
#define IRQ_GPIO3	25
#define IRQ_GPIO2	26
#define IRQ_GPIO1	27
#define IRQ_GPIO0	28
#define IRQ_IPU		29
#define IRQ_LCD		30


//************************************************************************
// RTC
//************************************************************************
#define RTC_RCR		REG32 (RTC_BASE + 0x00) // RTC Control Register
#define RTC_RSR		REG32 (RTC_BASE + 0x04) // RTC Second Register
#define RTC_RSAR	REG32 (RTC_BASE + 0x08) // RTC Second Alarm Register
#define RTC_RGR		REG32 (RTC_BASE + 0x0c) // RTC Regulator Register

#define RTC_HCR		REG32 (RTC_BASE + 0x20) // Hibernate Control Register
#define RTC_HWFCR	REG32 (RTC_BASE + 0x24) // Hibernate Wakeup Filter Counter Reg
#define RTC_HRCR	REG32 (RTC_BASE + 0x28) // Hibernate Reset Counter Register
#define RTC_HWCR	REG32 (RTC_BASE + 0x2c) // Hibernate Wakeup Control Register
#define RTC_HWRSR	REG32 (RTC_BASE + 0x30) // Hibernate Wakeup Status Register
#define RTC_HSPR	REG32 (RTC_BASE + 0x34) // Hibernate Scratch Pattern Register

// RTC Control Register
#define RTC_RCR_WRDY_BIT 7
#define RTC_RCR_WRDY	(1 << 7)  // Write Ready Flag
#define RTC_RCR_1HZ_BIT	6
#define RTC_RCR_1HZ	(1 << RTC_RCR_1HZ_BIT)  // 1Hz Flag
#define RTC_RCR_1HZIE	(1 << 5)  // 1Hz Interrupt Enable
#define RTC_RCR_AF_BIT	4
#define RTC_RCR_AF	(1 << RTC_RCR_AF_BIT)  // Alarm Flag
#define RTC_RCR_AIE	(1 << 3)  // Alarm Interrupt Enable
#define RTC_RCR_AE	(1 << 2)  // Alarm Enable
#define RTC_RCR_RTCE	(1 << 0)  // RTC Enable

// RTC Regulator Register
#define RTC_RGR_LOCK		(1 << 31) // Lock Bit
#define RTC_RGR_ADJC_BIT	16
#define RTC_RGR_ADJC_MASK	(0x3ff << RTC_RGR_ADJC_BIT)
#define RTC_RGR_NC1HZ_BIT	0
#define RTC_RGR_NC1HZ_MASK	(0xffff << RTC_RGR_NC1HZ_BIT)

// Hibernate Control Register
#define RTC_HCR_PD		(1 << 0)  // Power Down

// Hibernate Wakeup Filter Counter Register
#define RTC_HWFCR_BIT		5
#define RTC_HWFCR_MASK		(0x7ff << RTC_HWFCR_BIT)

// Hibernate Reset Counter Register
#define RTC_HRCR_BIT		5
#define RTC_HRCR_MASK		(0x7f << RTC_HRCR_BIT)

// Hibernate Wakeup Control Register
#define RTC_HWCR_EALM		(1 << 0)  // RTC alarm wakeup enable

// Hibernate Wakeup Status Register
#define RTC_HWRSR_HR		(1 << 5)  // Hibernate reset
#define RTC_HWRSR_PPR		(1 << 4)  // PPR reset
#define RTC_HWRSR_PIN		(1 << 1)  // Wakeup pin status bit
#define RTC_HWRSR_ALM		(1 << 0)  // RTC alarm status bit


//************************************************************************
// CPM (Clock reset and Power control Management)
//************************************************************************
#define CPM_CPCCR	REG32 (CPM_BASE+0x00)
#define CPM_CPPCR	REG32 (CPM_BASE+0x10)
#define CPM_I2SCDR	REG32 (CPM_BASE+0x60)
#define CPM_LPCDR	REG32 (CPM_BASE+0x64)
#define CPM_MSCCDR	REG32 (CPM_BASE+0x68)
#define CPM_UHCCDR	REG32 (CPM_BASE+0x6C)
#define CPM_SSICDR	REG32 (CPM_BASE+0x74)

#define CPM_LCR		REG32 (CPM_BASE+0x04)
#define CPM_CLKGR	REG32 (CPM_BASE+0x20)
#define CPM_SCR		REG32 (CPM_BASE+0x24)

#define CPM_HCR		REG32 (CPM_BASE+0x30)
#define CPM_HWFCR	REG32 (CPM_BASE+0x34)
#define CPM_HRCR	REG32 (CPM_BASE+0x38)
#define CPM_HWCR	REG32 (CPM_BASE+0x3c)
#define CPM_HWSR	REG32 (CPM_BASE+0x40)
#define CPM_HSPR	REG32 (CPM_BASE+0x44)

#define CPM_RSR		REG32 (CPM_BASE+0x08)


// Clock Control Register
#define CPM_CPCCR_I2CS		(1 << 31)
#define CPM_CPCCR_CLKOEN	(1 << 30)
#define CPM_CPCCR_UCS		(1 << 29)
#define CPM_CPCCR_UDIV_BIT	23
#define CPM_CPCCR_UDIV_MASK	(0x3f << CPM_CPCCR_UDIV_BIT)
#define CPM_CPCCR_CE		(1 << 22)
#define CPM_CPCCR_PCS		(1 << 21)
#define CPM_CPCCR_LDIV_BIT	16
#define CPM_CPCCR_LDIV_MASK	(0x1f << CPM_CPCCR_LDIV_BIT)
#define CPM_CPCCR_MDIV_BIT	12
#define CPM_CPCCR_MDIV_MASK	(0x0f << CPM_CPCCR_MDIV_BIT)
#define CPM_CPCCR_PDIV_BIT	8
#define CPM_CPCCR_PDIV_MASK	(0x0f << CPM_CPCCR_PDIV_BIT)
#define CPM_CPCCR_HDIV_BIT	4
#define CPM_CPCCR_HDIV_MASK	(0x0f << CPM_CPCCR_HDIV_BIT)
#define CPM_CPCCR_CDIV_BIT	0
#define CPM_CPCCR_CDIV_MASK	(0x0f << CPM_CPCCR_CDIV_BIT)

// I2S Clock Divider Register
#define CPM_I2SCDR_I2SDIV_BIT	0
#define CPM_I2SCDR_I2SDIV_MASK	(0x1ff << CPM_I2SCDR_I2SDIV_BIT)

// LCD Pixel Clock Divider Register
#define CPM_LPCDR_PIXDIV_BIT	0
#define CPM_LPCDR_PIXDIV_MASK	(0x1ff << CPM_LPCDR_PIXDIV_BIT)

// MSC Clock Divider Register
#define CPM_MSCCDR_MSCDIV_BIT	0
#define CPM_MSCCDR_MSCDIV_MASK	(0x1f << CPM_MSCCDR_MSCDIV_BIT)

// UHC Clock Divider Register
#define CPM_UHCCDR_UHCDIV_BIT	0
#define CPM_UHCCDR_UHCDIV_MASK	(0xf << CPM_UHCCDR_UHCDIV_BIT)

// SSI Clock Divider Register
#define CPM_SSICDR_SCS		(1<<31) // SSI clock source selection, 0:EXCLK, 1: PLL
#define CPM_SSICDR_SSIDIV_BIT	0
#define CPM_SSICDR_SSIDIV_MASK	(0xf << CPM_SSICDR_SSIDIV_BIT)

// PLL Control Register
#define CPM_CPPCR_PLLM_BIT	23
#define CPM_CPPCR_PLLM_MASK	(0x1ff << CPM_CPPCR_PLLM_BIT)
#define CPM_CPPCR_PLLN_BIT	18
#define CPM_CPPCR_PLLN_MASK	(0x1f << CPM_CPPCR_PLLN_BIT)
#define CPM_CPPCR_PLLOD_BIT	16
#define CPM_CPPCR_PLLOD_MASK	(0x03 << CPM_CPPCR_PLLOD_BIT)
#define CPM_CPPCR_PLLS		(1 << 10)
#define CPM_CPPCR_PLLBP		(1 << 9)
#define CPM_CPPCR_PLLEN		(1 << 8)
#define CPM_CPPCR_PLLST_BIT	0
#define CPM_CPPCR_PLLST_MASK	(0xff << CPM_CPPCR_PLLST_BIT)

// Low Power Control Register
#define CPM_LCR_DOZE_DUTY_BIT 	3
#define CPM_LCR_DOZE_DUTY_MASK 	(0x1f << CPM_LCR_DOZE_DUTY_BIT)
#define CPM_LCR_DOZE_ON		(1 << 2)
#define CPM_LCR_LPM_BIT		0
#define CPM_LCR_LPM_MASK	(0x3 << CPM_LCR_LPM_BIT)
  #define CPM_LCR_LPM_IDLE	(0x0 << CPM_LCR_LPM_BIT)
  #define CPM_LCR_LPM_SLEEP	(0x1 << CPM_LCR_LPM_BIT)

// Clock Gate Register
#define CPM_CLKGR_UART1		(1 << 15)
#define CPM_CLKGR_UHC		(1 << 14)
#define CPM_CLKGR_IPU		(1 << 13)
#define CPM_CLKGR_DMAC		(1 << 12)
#define CPM_CLKGR_UDC		(1 << 11)
#define CPM_CLKGR_LCD		(1 << 10)
#define CPM_CLKGR_CIM		(1 << 9)
#define CPM_CLKGR_SADC		(1 << 8)
#define CPM_CLKGR_MSC		(1 << 7)
#define CPM_CLKGR_AIC1		(1 << 6)
#define CPM_CLKGR_AIC2		(1 << 5)
#define CPM_CLKGR_SSI		(1 << 4)
#define CPM_CLKGR_I2C		(1 << 3)
#define CPM_CLKGR_RTC		(1 << 2)
#define CPM_CLKGR_TCU		(1 << 1)
#define CPM_CLKGR_UART0		(1 << 0)

// Sleep Control Register
#define CPM_SCR_O1ST_BIT	8
#define CPM_SCR_O1ST_MASK	(0xff << CPM_SCR_O1ST_BIT)
#define CPM_SCR_USBPHY_ENABLE	(1 << 6)
#define CPM_SCR_OSC_ENABLE	(1 << 4)

// Hibernate Control Register
#define CPM_HCR_PD		(1 << 0)

// Wakeup Filter Counter Register in Hibernate Mode
#define CPM_HWFCR_TIME_BIT	0
#define CPM_HWFCR_TIME_MASK	(0x3ff << CPM_HWFCR_TIME_BIT)

// Reset Counter Register in Hibernate Mode
#define CPM_HRCR_TIME_BIT	0
#define CPM_HRCR_TIME_MASK	(0x7f << CPM_HRCR_TIME_BIT)

// Wakeup Control Register in Hibernate Mode
#define CPM_HWCR_WLE_LOW	(0 << 2)
#define CPM_HWCR_WLE_HIGH	(1 << 2)
#define CPM_HWCR_PIN_WAKEUP	(1 << 1)
#define CPM_HWCR_RTC_WAKEUP	(1 << 0)

// Wakeup Status Register in Hibernate Mode
#define CPM_HWSR_WSR_PIN	(1 << 1)
#define CPM_HWSR_WSR_RTC	(1 << 0)

// Reset Status Register
#define CPM_RSR_HR		(1 << 2)
#define CPM_RSR_WR		(1 << 1)
#define CPM_RSR_PR		(1 << 0)


//************************************************************************
// TCU (Timer Counter Unit)
//************************************************************************
#define TCU_TSR		REG32 (TCU_BASE + 0x1C) // Timer Stop Register
#define TCU_TSSR	REG32 (TCU_BASE + 0x2C) // Timer Stop Set Register
#define TCU_TSCR	REG32 (TCU_BASE + 0x3C) // Timer Stop Clear Register
#define TCU_TER		REG8 (TCU_BASE + 0x10) // Timer Counter Enable Register
#define TCU_TESR	REG8 (TCU_BASE + 0x14) // Timer Counter Enable Set Register
#define TCU_TECR	REG8 (TCU_BASE + 0x18) // Timer Counter Enable Clear Register
#define TCU_TFR		REG32 (TCU_BASE + 0x20) // Timer Flag Register
#define TCU_TFSR	REG32 (TCU_BASE + 0x24) // Timer Flag Set Register
#define TCU_TFCR	REG32 (TCU_BASE + 0x28) // Timer Flag Clear Register
#define TCU_TMR		REG32 (TCU_BASE + 0x30) // Timer Mask Register
#define TCU_TMSR	REG32 (TCU_BASE + 0x34) // Timer Mask Set Register
#define TCU_TMCR	REG32 (TCU_BASE + 0x38) // Timer Mask Clear Register

// n = 0,1,2,3,4,5
#define TCU_TDFR(n)	REG16 (TCU_BASE + (0x40 + (n)*0x10)) // Timer Data Full Reg
#define TCU_TDHR(n)	REG16 (TCU_BASE + (0x44 + (n)*0x10)) // Timer Data Half Reg
#define TCU_TCNT(n)	REG16 (TCU_BASE + (0x48 + (n)*0x10)) // Timer Counter Reg
#define TCU_TCSR(n)	REG16 (TCU_BASE + (0x4C + (n)*0x10)) // Timer Control Reg

// Register definitions
#define TCU_TCSR_PWM_SD		(1 << 9)
#define TCU_TCSR_PWM_INITL_HIGH	(1 << 8)
#define TCU_TCSR_PWM_EN		(1 << 7)
#define TCU_TCSR_PRESCALE_BIT	3
#define TCU_TCSR_PRESCALE_MASK	(0x7 << TCU_TCSR_PRESCALE_BIT)
  #define TCU_TCSR_PRESCALE1	(0x0 << TCU_TCSR_PRESCALE_BIT)
  #define TCU_TCSR_PRESCALE4	(0x1 << TCU_TCSR_PRESCALE_BIT)
  #define TCU_TCSR_PRESCALE16	(0x2 << TCU_TCSR_PRESCALE_BIT)
  #define TCU_TCSR_PRESCALE64	(0x3 << TCU_TCSR_PRESCALE_BIT)
  #define TCU_TCSR_PRESCALE256	(0x4 << TCU_TCSR_PRESCALE_BIT)
  #define TCU_TCSR_PRESCALE1024	(0x5 << TCU_TCSR_PRESCALE_BIT)
#define TCU_TCSR_EXT_EN		(1 << 2)
#define TCU_TCSR_RTC_EN		(1 << 1)
#define TCU_TCSR_PCK_EN		(1 << 0)

#define TCU_TER_TCEN(n)		(1 << (n))
#define TCU_TESR_TCST(n)	(1 << (n))
#define TCU_TECR_TCCL(n)	(1 << (n))
#define TCU_TFR_HFLAG(n)	(1 << ((n) + 16))
#define TCU_TFR_FFLAG(n)	(1 << (n))
#define TCU_TFSR_HFLAG(n)	(1 << ((n) + 16))
#define TCU_TFSR_FFLAG(n)	(1 << (n))
#define TCU_TFCR_HFLAG(n)	(1 << ((n) + 16))
#define TCU_TFCR_FFLAG(n)	(1 << (n))
#define TCU_TMR_HMASK(n)	(1 << ((n) + 16))
#define TCU_TMR_FMASK(n)	(1 << (n))
#define TCU_TMSR_HMST(n)	(1 << ((n) + 16))
#define TCU_TMSR_FMST(n)	(1 << (n))
#define TCU_TMCR_HMCL(n)	(1 << ((n) + 16))
#define TCU_TMCR_FMCL(n)	(1 << (n))
#define TCU_TSR_WDTS		(1 << 16)
#define TCU_TSR_STOP(n)		(1 << (n))
#define TCU_TSSR_WDTSS		(1 << 16)
#define TCU_TSSR_STPS(n)	(1 << (n))
#define TCU_TSSR_WDTSC		(1 << 16)
#define TCU_TSSR_STPC(n)	(1 << (n))


//************************************************************************
// WDT (WatchDog Timer)
//************************************************************************
#define WDT_TDR		REG16 (WDT_BASE + 0x00)
#define WDT_TCER	REG8 (WDT_BASE + 0x04)
#define WDT_TCNT	REG16 (WDT_BASE + 0x08)
#define WDT_TCSR	REG16 (WDT_BASE + 0x0C)

// Register definition
#define WDT_TCSR_PRESCALE_BIT	3
#define WDT_TCSR_PRESCALE_MASK	(0x7 << WDT_TCSR_PRESCALE_BIT)
  #define WDT_TCSR_PRESCALE1	(0x0 << WDT_TCSR_PRESCALE_BIT)
  #define WDT_TCSR_PRESCALE4	(0x1 << WDT_TCSR_PRESCALE_BIT)
  #define WDT_TCSR_PRESCALE16	(0x2 << WDT_TCSR_PRESCALE_BIT)
  #define WDT_TCSR_PRESCALE64	(0x3 << WDT_TCSR_PRESCALE_BIT)
  #define WDT_TCSR_PRESCALE256	(0x4 << WDT_TCSR_PRESCALE_BIT)
  #define WDT_TCSR_PRESCALE1024	(0x5 << WDT_TCSR_PRESCALE_BIT)
#define WDT_TCSR_EXT_EN		(1 << 2)
#define WDT_TCSR_RTC_EN		(1 << 1)
#define WDT_TCSR_PCK_EN		(1 << 0)

#define WDT_TCER_TCEN		(1 << 0)


//************************************************************************
// DMAC (DMA Controller)
//************************************************************************

#define MAX_DMA_NUM	6  // max 6 channels

#define DMAC_DSAR(n)	REG32 (DMAC_BASE + (0x00 + (n) * 0x20)) // DMA source address
#define DMAC_DTAR(n)	REG32 (DMAC_BASE + (0x04 + (n) * 0x20)) // DMA target address
#define DMAC_DTCR(n)	REG32 (DMAC_BASE + (0x08 + (n) * 0x20)) // DMA transfer count
#define DMAC_DRSR(n)	REG32 (DMAC_BASE + (0x0c + (n) * 0x20)) // DMA request source
#define DMAC_DCCSR(n)	REG32 (DMAC_BASE + (0x10 + (n) * 0x20)) // DMA control/status
#define DMAC_DCMD(n)	REG32 (DMAC_BASE + (0x14 + (n) * 0x20)) // DMA command
#define DMAC_DDA(n)	REG32 (DMAC_BASE + (0x18 + (n) * 0x20)) // DMA descriptor address
#define DMAC_DMACR	REG32 (DMAC_BASE + 0x0300)              // DMA control register
#define DMAC_DMAIPR	REG32 (DMAC_BASE + 0x0304)              // DMA interrupt pending
#define DMAC_DMADBR	REG32 (DMAC_BASE + 0x0308)              // DMA doorbell
#define DMAC_DMADBSR	REG32 (DMAC_BASE + 0x030C)              // DMA doorbell set

// DMA request source register
#define DMAC_DRSR_RS_BIT	0
#define DMAC_DRSR_RS_MASK	(0x1f << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_AUTO	(8 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_UART0OUT	(20 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_UART0IN	(21 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_SSIOUT	(22 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_SSIIN	(23 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_AICOUT	(24 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_AICIN	(25 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_MSCOUT	(26 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_MSCIN	(27 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_TCU	(28 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_SADC	(29 << DMAC_DRSR_RS_BIT)
  #define DMAC_DRSR_RS_SLCD	(30 << DMAC_DRSR_RS_BIT)

// DMA channel control/status register
#define DMAC_DCCSR_NDES		(1 << 31) // descriptor (0) or not (1) ?
#define DMAC_DCCSR_CDOA_BIT	16        // copy of DMA offset address
#define DMAC_DCCSR_CDOA_MASK	(0xff << DMAC_DCCSR_CDOA_BIT)
#define DMAC_DCCSR_INV		(1 << 6)  // descriptor invalid
#define DMAC_DCCSR_AR		(1 << 4)  // address error
#define DMAC_DCCSR_TT		(1 << 3)  // transfer terminated
#define DMAC_DCCSR_HLT		(1 << 2)  // DMA halted
#define DMAC_DCCSR_CT		(1 << 1)  // count terminated
#define DMAC_DCCSR_EN		(1 << 0)  // channel enable bit

// DMA channel command register 
#define DMAC_DCMD_SAI		(1 << 23) // source address increment
#define DMAC_DCMD_DAI		(1 << 22) // dest address increment
#define DMAC_DCMD_RDIL_BIT	16        // request detection interval length
#define DMAC_DCMD_RDIL_MASK	(0x0f << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_IGN	(0 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_2	(1 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_4	(2 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_8	(3 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_12	(4 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_16	(5 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_20	(6 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_24	(7 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_28	(8 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_32	(9 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_48	(10 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_60	(11 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_64	(12 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_124	(13 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_128	(14 << DMAC_DCMD_RDIL_BIT)
  #define DMAC_DCMD_RDIL_200	(15 << DMAC_DCMD_RDIL_BIT)
#define DMAC_DCMD_SWDH_BIT	14  // source port width
#define DMAC_DCMD_SWDH_MASK	(0x03 << DMAC_DCMD_SWDH_BIT)
  #define DMAC_DCMD_SWDH_32	(0 << DMAC_DCMD_SWDH_BIT)
  #define DMAC_DCMD_SWDH_8	(1 << DMAC_DCMD_SWDH_BIT)
  #define DMAC_DCMD_SWDH_16	(2 << DMAC_DCMD_SWDH_BIT)
#define DMAC_DCMD_DWDH_BIT	12  // dest port width
#define DMAC_DCMD_DWDH_MASK	(0x03 << DMAC_DCMD_DWDH_BIT)
  #define DMAC_DCMD_DWDH_32	(0 << DMAC_DCMD_DWDH_BIT)
  #define DMAC_DCMD_DWDH_8	(1 << DMAC_DCMD_DWDH_BIT)
  #define DMAC_DCMD_DWDH_16	(2 << DMAC_DCMD_DWDH_BIT)
#define DMAC_DCMD_DS_BIT	8  // transfer data size of a data unit
#define DMAC_DCMD_DS_MASK	(0x07 << DMAC_DCMD_DS_BIT)
  #define DMAC_DCMD_DS_32BIT	(0 << DMAC_DCMD_DS_BIT)
  #define DMAC_DCMD_DS_8BIT	(1 << DMAC_DCMD_DS_BIT)
  #define DMAC_DCMD_DS_16BIT	(2 << DMAC_DCMD_DS_BIT)
  #define DMAC_DCMD_DS_16BYTE	(3 << DMAC_DCMD_DS_BIT)
  #define DMAC_DCMD_DS_32BYTE	(4 << DMAC_DCMD_DS_BIT)
#define DMAC_DCMD_TM		(1 << 7)  // transfer mode: 0-single 1-block
#define DMAC_DCMD_DES_V		(1 << 4)  // descriptor valid flag
#define DMAC_DCMD_DES_VM	(1 << 3)  // descriptor valid mask: 1:support V-bit
#define DMAC_DCMD_DES_VIE	(1 << 2)  // DMA valid error interrupt enable
#define DMAC_DCMD_TIE		(1 << 1)  // DMA transfer interrupt enable
#define DMAC_DCMD_LINK		(1 << 0)  // descriptor link enable

// DMA descriptor address register
#define DMAC_DDA_BASE_BIT	12  // descriptor base address
#define DMAC_DDA_BASE_MASK	(0x0fffff << DMAC_DDA_BASE_BIT)
#define DMAC_DDA_OFFSET_BIT	4  // descriptor offset address
#define DMAC_DDA_OFFSET_MASK	(0x0ff << DMAC_DDA_OFFSET_BIT)

// DMA control register
#define DMAC_DMACR_PR_BIT	8  // channel priority mode
#define DMAC_DMACR_PR_MASK	(0x03 << DMAC_DMACR_PR_BIT)
  #define DMAC_DMACR_PR_012345	(0 << DMAC_DMACR_PR_BIT)
  #define DMAC_DMACR_PR_023145	(1 << DMAC_DMACR_PR_BIT)
  #define DMAC_DMACR_PR_201345	(2 << DMAC_DMACR_PR_BIT)
  #define DMAC_DMACR_PR_RR	(3 << DMAC_DMACR_PR_BIT) // round robin
#define DMAC_DMACR_HLT		(1 << 3)  // DMA halt flag
#define DMAC_DMACR_AR		(1 << 2)  // address error flag
#define DMAC_DMACR_DMAE		(1 << 0)  // DMA enable bit
#define DMAC_DMADBR_DB		(1 << 5)  // doorbell
#define DMAC_DMADBSR_DBS	(1 << 5)  // enable doorbell
#define DMAC_DMAIPR_CIRQ(n)	(1 << n)  // irq pending status for channel n


//************************************************************************
// GPIO (General-Purpose I/O Ports)
//************************************************************************
#define MAX_GPIO_NUM	128

//n = 0,1,2,3
#define GPIO_PXPIN(n)	REG32 (GPIO_BASE + (0x00 + (n)*0x100)) // PIN Level Register
#define GPIO_PXDAT(n)	REG32 (GPIO_BASE + (0x10 + (n)*0x100)) // Port Data Register 		1: interrupt pending
#define GPIO_PXDATS(n)	REG32 (GPIO_BASE + (0x14 + (n)*0x100)) // Port Data Set Register
#define GPIO_PXDATC(n)	REG32 (GPIO_BASE + (0x18 + (n)*0x100)) // Port Data Clear Register
#define GPIO_PXIM(n)	REG32 (GPIO_BASE + (0x20 + (n)*0x100)) // Interrupt Mask Register	1: mask pin interrupt
#define GPIO_PXIMS(n)	REG32 (GPIO_BASE + (0x24 + (n)*0x100)) // Interrupt Mask Set Reg
#define GPIO_PXIMC(n)	REG32 (GPIO_BASE + (0x28 + (n)*0x100)) // Interrupt Mask Clear Reg
#define GPIO_PXPE(n)	REG32 (GPIO_BASE + (0x30 + (n)*0x100)) // Pull Enable Register		1: disable pull up/down
#define GPIO_PXPES(n)	REG32 (GPIO_BASE + (0x34 + (n)*0x100)) // Pull Enable Set Reg.
#define GPIO_PXPEC(n)	REG32 (GPIO_BASE + (0x38 + (n)*0x100)) // Pull Enable Clear Reg.
#define GPIO_PXFUN(n)	REG32 (GPIO_BASE + (0x40 + (n)*0x100)) // Function Register		0: gpio; 1: function
#define GPIO_PXFUNS(n)	REG32 (GPIO_BASE + (0x44 + (n)*0x100)) // Function Set Register
#define GPIO_PXFUNC(n)	REG32 (GPIO_BASE + (0x48 + (n)*0x100)) // Function Clear Register
#define GPIO_PXSEL(n)	REG32 (GPIO_BASE + (0x50 + (n)*0x100)) // Select Register		0: gpio/fun0; 1: intr/fun1
#define GPIO_PXSELS(n)	REG32 (GPIO_BASE + (0x54 + (n)*0x100)) // Select Set Register
#define GPIO_PXSELC(n)	REG32 (GPIO_BASE + (0x58 + (n)*0x100)) // Select Clear Register
#define GPIO_PXDIR(n)	REG32 (GPIO_BASE + (0x60 + (n)*0x100)) // Direction Register		0:input/low-level-trig/falling-edge-trig, 1:output/high-level-trig/rising-edge-trig
#define GPIO_PXDIRS(n)	REG32 (GPIO_BASE + (0x64 + (n)*0x100)) // Direction Set Register
#define GPIO_PXDIRC(n)	REG32 (GPIO_BASE + (0x68 + (n)*0x100)) // Direction Clear Register
#define GPIO_PXTRG(n)	REG32 (GPIO_BASE + (0x70 + (n)*0x100)) // Trigger Register		0:level-trigger, 1:edge-trigger
#define GPIO_PXTRGS(n)	REG32 (GPIO_BASE + (0x74 + (n)*0x100)) // Trigger Set Register
#define GPIO_PXTRGC(n)	REG32 (GPIO_BASE + (0x78 + (n)*0x100)) // Trigger Set Register
#define GPIO_PXFLG(n)	REG32 (GPIO_BASE + (0x80 + (n)*0x100)) // Port Flag Register		interrupt flag
#define GPIO_PXFLGC(n)	REG32 (GPIO_BASE + (0x14 + (n)*0x100)) // Port Flag Clear Register


//************************************************************************
// UART
//************************************************************************

#define IRDA_BASE	UART0_BASE
#define UART_BASE	UART0_BASE
#define UART_OFF	0x1000

// Register Offset
#define OFF_RDR		(0x00)	// R  8b H'xx
#define OFF_TDR		(0x00)	// W  8b H'xx
#define OFF_DLLR	(0x00)	// RW 8b H'00
#define OFF_DLHR	(0x04)	// RW 8b H'00
#define OFF_IER		(0x04)	// RW 8b H'00
#define OFF_ISR		(0x08)	// R  8b H'01
#define OFF_FCR		(0x08)	// W  8b H'00
#define OFF_LCR		(0x0C)	// RW 8b H'00
#define OFF_MCR		(0x10)	// RW 8b H'00
#define OFF_LSR		(0x14)	// R  8b H'00
#define OFF_MSR		(0x18)	// R  8b H'00
#define OFF_SPR		(0x1C)	// RW 8b H'00
#define OFF_SIRCR	(0x20)	// RW 8b H'00, UART0
#define OFF_UMR		(0x24)	// RW 8b H'00, UART M Register
#define OFF_UACR	(0x28)	// RW 8b H'00, UART Add Cycle Register

// Register Address
#define UART0_RDR	REG8 (UART0_BASE + OFF_RDR)
#define UART0_TDR	REG8 (UART0_BASE + OFF_TDR)
#define UART0_DLLR	REG8 (UART0_BASE + OFF_DLLR)
#define UART0_DLHR	REG8 (UART0_BASE + OFF_DLHR)
#define UART0_IER	REG8 (UART0_BASE + OFF_IER)
#define UART0_ISR	REG8 (UART0_BASE + OFF_ISR)
#define UART0_FCR	REG8 (UART0_BASE + OFF_FCR)
#define UART0_LCR	REG8 (UART0_BASE + OFF_LCR)
#define UART0_MCR	REG8 (UART0_BASE + OFF_MCR)
#define UART0_LSR	REG8 (UART0_BASE + OFF_LSR)
#define UART0_MSR	REG8 (UART0_BASE + OFF_MSR)
#define UART0_SPR	REG8 (UART0_BASE + OFF_SPR)
#define UART0_SIRCR	REG8 (UART0_BASE + OFF_SIRCR)
#define UART0_UMR	REG8 (UART0_BASE + OFF_UMR)
#define UART0_UACR	REG8 (UART0_BASE + OFF_UACR)

// UART Interrupt Enable Register
#define UARTIER_RIE	(1 << 0)	// 0: receive fifo full interrupt disable
#define UARTIER_TIE	(1 << 1)	// 0: transmit fifo empty interrupt disable
#define UARTIER_RLIE	(1 << 2)	// 0: receive line status interrupt disable
#define UARTIER_MIE	(1 << 3)	// 0: modem status interrupt disable
#define UARTIER_RTIE	(1 << 4)	// 0: receive timeout interrupt disable

// UART Interrupt Status Register
#define UARTISR_IP	(1 << 0)	// 0: interrupt is pending  1: no interrupt
#define UARTISR_IID	(7 << 1)	// Source of Interrupt
#define UARTISR_IID_MSI		(0 << 1)  // Modem status interrupt
#define UARTISR_IID_THRI	(1 << 1)  // Transmitter holding register empty
#define UARTISR_IID_RDI		(2 << 1)  // Receiver data interrupt
#define UARTISR_IID_RLSI	(3 << 1)  // Receiver line status interrupt
#define UARTISR_IID_RTO		(6 << 1)  // Receive timeout
#define UARTISR_FFMS		(3 << 6)  // FIFO mode select, set when UARTFCR.FE is set to 1
#define UARTISR_FFMS_NO_FIFO	(0 << 6)
#define UARTISR_FFMS_FIFO_MODE	(3 << 6)

// UART FIFO Control Register
#define UARTFCR_FE	(1 << 0)	// 0: non-FIFO mode  1: FIFO mode
#define UARTFCR_RFLS	(1 << 1)	// write 1 to flush receive FIFO
#define UARTFCR_TFLS	(1 << 2)	// write 1 to flush transmit FIFO
#define UARTFCR_DMS	(1 << 3)	// 0: disable DMA mode
#define UARTFCR_UUE	(1 << 4)	// 0: disable UART
#define UARTFCR_RTRG	(3 << 6)	// Receive FIFO Data Trigger
#define UARTFCR_RTRG_1	(0 << 6)
#define UARTFCR_RTRG_4	(1 << 6)
#define UARTFCR_RTRG_8	(2 << 6)
#define UARTFCR_RTRG_15	(3 << 6)

// UART Line Control Register
#define UARTLCR_WLEN	(3 << 0)	// word length
#define UARTLCR_WLEN_5	(0 << 0)
#define UARTLCR_WLEN_6	(1 << 0)
#define UARTLCR_WLEN_7	(2 << 0)
#define UARTLCR_WLEN_8	(3 << 0)
#define UARTLCR_STOP	(1 << 2)	// 0: 1 stop bit when word length is 5,6,7,8	 1: 1.5 stop bits when 5; 2 stop bits when 6,7,8
#define UARTLCR_STOP1	(0 << 2)
#define UARTLCR_STOP2	(1 << 2)
#define UARTLCR_PE	(1 << 3)	// 0: parity disable
#define UARTLCR_PROE	(1 << 4)	// 0: even parity  1: odd parity
#define UARTLCR_SPAR	(1 << 5)	// 0: sticky parity disable
#define UARTLCR_SBRK	(1 << 6)	// write 0 normal, write 1 send break
#define UARTLCR_DLAB	(1 << 7)	// 0: access UARTRDR/TDR/IER  1: access UARTDLLR/DLHR

// UART Line Status Register
#define UARTLSR_DR	(1 << 0)	// 0: receive FIFO is empty  1: receive data is ready
#define UARTLSR_ORER	(1 << 1)	// 0: no overrun error
#define UARTLSR_PER	(1 << 2)	// 0: no parity error
#define UARTLSR_FER	(1 << 3)	// 0; no framing error
#define UARTLSR_BRK	(1 << 4)	// 0: no break detected  1: receive a break signal
#define UARTLSR_TDRQ	(1 << 5)	// 1: transmit FIFO half "empty"
#define UARTLSR_TEMT	(1 << 6)	// 1: transmit FIFO and shift registers empty
#define UARTLSR_RFER	(1 << 7)	// 0: no receive error  1: receive error in FIFO mode

// UART Modem Control Register
#define UARTMCR_RTS	(1 << 1)	// 0: RTS_ output high, 1: RTS_ output low
#define UARTMCR_LOOP	(1 << 4)	// 0: normal  1: loopback mode
#define UARTMCR_MCE	(1 << 7)	// 0: modem function is disable

// UART Modem Status Register
#define UARTMSR_CCTS	(1 << 0)        // 1: a change on CTS_ pin
#define UARTMSR_CTS	(1 << 4)	// 0: CTS_ pin is high

// Slow IrDA Control Register
#define SIRCR_TSIRE	(1 << 0)  // 0: transmitter is in UART mode  1: SIR mode
#define SIRCR_RSIRE	(1 << 1)  // 0: receiver is in UART mode  1: SIR mode
#define SIRCR_TPWS	(1 << 2)  // 0: transmit 0 pulse width is 3/16 of bit length	1: 0 pulse width is 1.6us for 115.2Kbps
#define SIRCR_TDPL	(1 << 3)  // 0: encoder generates a positive pulse for 0
#define SIRCR_RDPL	(1 << 4)  // 0: decoder interprets positive pulse as 0


//************************************************************************
// AIC (AC97/I2S Controller)
//************************************************************************
#define	AIC_FR			REG32 (AIC_BASE + 0x000)
#define	AIC_CR			REG32 (AIC_BASE + 0x004)
#define	AIC_ACCR1		REG32 (AIC_BASE + 0x008)
#define	AIC_ACCR2		REG32 (AIC_BASE + 0x00C)
#define	AIC_I2SCR		REG32 (AIC_BASE + 0x010)
#define	AIC_SR			REG32 (AIC_BASE + 0x014)
#define	AIC_ACSR		REG32 (AIC_BASE + 0x018)
#define	AIC_I2SSR		REG32 (AIC_BASE + 0x01C)
#define	AIC_ACCAR		REG32 (AIC_BASE + 0x020)
#define	AIC_ACCDR		REG32 (AIC_BASE + 0x024)
#define	AIC_ACSAR		REG32 (AIC_BASE + 0x028)
#define	AIC_ACSDR		REG32 (AIC_BASE + 0x02C)
#define	AIC_I2SDIV		REG32 (AIC_BASE + 0x030)
#define	AIC_DR			REG32 (AIC_BASE + 0x034)

// AIC Controller Configuration Register (AIC_FR)

#define	AIC_FR_RFTH_BIT		12        // Receive FIFO Threshold
#define	AIC_FR_RFTH_MASK	(0xf << AIC_FR_RFTH_BIT)
#define	AIC_FR_TFTH_BIT		8         // Transmit FIFO Threshold
#define	AIC_FR_TFTH_MASK	(0xf << AIC_FR_TFTH_BIT)
#define	AIC_FR_LSMP		(1 << 6)  // Play Zero sample or last sample
#define	AIC_FR_ICDC		(1 << 5)  // External(0) or Internal CODEC(1)
#define	AIC_FR_AUSEL		(1 << 4)  // AC97(0) or I2S/MSB-justified(1)
#define	AIC_FR_RST		(1 << 3)  // AIC registers reset
#define	AIC_FR_BCKD		(1 << 2)  // I2S BIT_CLK direction, 0:input,1:output
#define	AIC_FR_SYNCD		(1 << 1)  // I2S SYNC direction, 0:input,1:output
#define	AIC_FR_ENB		(1 << 0)  // AIC enable bit

// AIC Controller Common Control Register (AIC_CR)

#define	AIC_CR_OSS_BIT		19  // Output Sample Size from memory (AIC V2 only)
#define	AIC_CR_OSS_MASK		(0x7 << AIC_CR_OSS_BIT)
  #define AIC_CR_OSS_8BIT	(0x0 << AIC_CR_OSS_BIT)
  #define AIC_CR_OSS_16BIT	(0x1 << AIC_CR_OSS_BIT)
  #define AIC_CR_OSS_18BIT	(0x2 << AIC_CR_OSS_BIT)
  #define AIC_CR_OSS_20BIT	(0x3 << AIC_CR_OSS_BIT)
  #define AIC_CR_OSS_24BIT	(0x4 << AIC_CR_OSS_BIT)
#define	AIC_CR_ISS_BIT		16  // Input Sample Size from memory (AIC V2 only)
#define	AIC_CR_ISS_MASK		(0x7 << AIC_CR_ISS_BIT)
  #define AIC_CR_ISS_8BIT	(0x0 << AIC_CR_ISS_BIT)
  #define AIC_CR_ISS_16BIT	(0x1 << AIC_CR_ISS_BIT)
  #define AIC_CR_ISS_18BIT	(0x2 << AIC_CR_ISS_BIT)
  #define AIC_CR_ISS_20BIT	(0x3 << AIC_CR_ISS_BIT)
  #define AIC_CR_ISS_24BIT	(0x4 << AIC_CR_ISS_BIT)
#define	AIC_CR_RDMS		(1 << 15)  // Receive DMA enable
#define	AIC_CR_TDMS		(1 << 14)  // Transmit DMA enable
#define	AIC_CR_M2S		(1 << 11)  // Mono to Stereo enable
#define	AIC_CR_ENDSW		(1 << 10)  // Endian switch enable
#define	AIC_CR_AVSTSU		(1 << 9)   // Signed <-> Unsigned toggle enable
#define	AIC_CR_FLUSH		(1 << 8)   // Flush FIFO
#define	AIC_CR_EROR		(1 << 6)   // Enable ROR interrupt
#define	AIC_CR_ETUR		(1 << 5)   // Enable TUR interrupt
#define	AIC_CR_ERFS		(1 << 4)   // Enable RFS interrupt
#define	AIC_CR_ETFS		(1 << 3)   // Enable TFS interrupt
#define	AIC_CR_ENLBF		(1 << 2)   // Enable Loopback Function
#define	AIC_CR_ERPL		(1 << 1)   // Enable Playback Function
#define	AIC_CR_EREC		(1 << 0)   // Enable Record Function

// AIC Controller AC-link Control Register 1 (AIC_ACCR1)

#define	AIC_ACCR1_RS_BIT	16          // Receive Valid Slots
#define	AIC_ACCR1_RS_MASK	(0x3ff << AIC_ACCR1_RS_BIT)
  #define AIC_ACCR1_RS_SLOT12	  (1 << 25) // Slot 12 valid bit
  #define AIC_ACCR1_RS_SLOT11	  (1 << 24) // Slot 11 valid bit
  #define AIC_ACCR1_RS_SLOT10	  (1 << 23) // Slot 10 valid bit
  #define AIC_ACCR1_RS_SLOT9	  (1 << 22) // Slot 9 valid bit, LFE
  #define AIC_ACCR1_RS_SLOT8	  (1 << 21) // Slot 8 valid bit, Surround Right
  #define AIC_ACCR1_RS_SLOT7	  (1 << 20) // Slot 7 valid bit, Surround Left
  #define AIC_ACCR1_RS_SLOT6	  (1 << 19) // Slot 6 valid bit, PCM Center
  #define AIC_ACCR1_RS_SLOT5	  (1 << 18) // Slot 5 valid bit
  #define AIC_ACCR1_RS_SLOT4	  (1 << 17) // Slot 4 valid bit, PCM Right
  #define AIC_ACCR1_RS_SLOT3	  (1 << 16) // Slot 3 valid bit, PCM Left
#define	AIC_ACCR1_XS_BIT	0          // Transmit Valid Slots
#define	AIC_ACCR1_XS_MASK	(0x3ff << AIC_ACCR1_XS_BIT)
  #define AIC_ACCR1_XS_SLOT12	  (1 << 9) // Slot 12 valid bit
  #define AIC_ACCR1_XS_SLOT11	  (1 << 8) // Slot 11 valid bit
  #define AIC_ACCR1_XS_SLOT10	  (1 << 7) // Slot 10 valid bit
  #define AIC_ACCR1_XS_SLOT9	  (1 << 6) // Slot 9 valid bit, LFE
  #define AIC_ACCR1_XS_SLOT8	  (1 << 5) // Slot 8 valid bit, Surround Right
  #define AIC_ACCR1_XS_SLOT7	  (1 << 4) // Slot 7 valid bit, Surround Left
  #define AIC_ACCR1_XS_SLOT6	  (1 << 3) // Slot 6 valid bit, PCM Center
  #define AIC_ACCR1_XS_SLOT5	  (1 << 2) // Slot 5 valid bit
  #define AIC_ACCR1_XS_SLOT4	  (1 << 1) // Slot 4 valid bit, PCM Right
  #define AIC_ACCR1_XS_SLOT3	  (1 << 0) // Slot 3 valid bit, PCM Left

// AIC Controller AC-link Control Register 2 (AIC_ACCR2)

#define	AIC_ACCR2_ERSTO		(1 << 18) // Enable RSTO interrupt
#define	AIC_ACCR2_ESADR		(1 << 17) // Enable SADR interrupt
#define	AIC_ACCR2_ECADT		(1 << 16) // Enable CADT interrupt
#define	AIC_ACCR2_OASS_BIT	8  // Output Sample Size for AC-link
#define	AIC_ACCR2_OASS_MASK	(0x3 << AIC_ACCR2_OASS_BIT)
  #define AIC_ACCR2_OASS_20BIT	  (0 << AIC_ACCR2_OASS_BIT) // Output Audio Sample Size is 20-bit
  #define AIC_ACCR2_OASS_18BIT	  (1 << AIC_ACCR2_OASS_BIT) // Output Audio Sample Size is 18-bit
  #define AIC_ACCR2_OASS_16BIT	  (2 << AIC_ACCR2_OASS_BIT) // Output Audio Sample Size is 16-bit
  #define AIC_ACCR2_OASS_8BIT	  (3 << AIC_ACCR2_OASS_BIT) // Output Audio Sample Size is 8-bit
#define	AIC_ACCR2_IASS_BIT	6  // Output Sample Size for AC-link
#define	AIC_ACCR2_IASS_MASK	(0x3 << AIC_ACCR2_IASS_BIT)
  #define AIC_ACCR2_IASS_20BIT	  (0 << AIC_ACCR2_IASS_BIT) // Input Audio Sample Size is 20-bit
  #define AIC_ACCR2_IASS_18BIT	  (1 << AIC_ACCR2_IASS_BIT) // Input Audio Sample Size is 18-bit
  #define AIC_ACCR2_IASS_16BIT	  (2 << AIC_ACCR2_IASS_BIT) // Input Audio Sample Size is 16-bit
  #define AIC_ACCR2_IASS_8BIT	  (3 << AIC_ACCR2_IASS_BIT) // Input Audio Sample Size is 8-bit
#define	AIC_ACCR2_SO		(1 << 3)  // SDATA_OUT output value
#define	AIC_ACCR2_SR		(1 << 2)  // RESET# pin level
#define	AIC_ACCR2_SS		(1 << 1)  // SYNC pin level
#define	AIC_ACCR2_SA		(1 << 0)  // SYNC and SDATA_OUT alternation

// AIC Controller I2S/MSB-justified Control Register (AIC_I2SCR)

#define	AIC_I2SCR_STPBK		(1 << 12) // Stop BIT_CLK for I2S/MSB-justified
#define	AIC_I2SCR_WL_BIT	1  // Input/Output Sample Size for I2S/MSB-justified
#define	AIC_I2SCR_WL_MASK	(0x7 << AIC_I2SCR_WL_BIT)
  #define AIC_I2SCR_WL_24BIT	  (0 << AIC_I2SCR_WL_BIT) // Word Length is 24 bit
  #define AIC_I2SCR_WL_20BIT	  (1 << AIC_I2SCR_WL_BIT) // Word Length is 20 bit
  #define AIC_I2SCR_WL_18BIT	  (2 << AIC_I2SCR_WL_BIT) // Word Length is 18 bit
  #define AIC_I2SCR_WL_16BIT	  (3 << AIC_I2SCR_WL_BIT) // Word Length is 16 bit
  #define AIC_I2SCR_WL_8BIT	  (4 << AIC_I2SCR_WL_BIT) // Word Length is 8 bit
#define	AIC_I2SCR_AMSL		(1 << 0) // 0:I2S, 1:MSB-justified

// AIC Controller FIFO Status Register (AIC_SR)

#define	AIC_SR_RFL_BIT		24  // Receive FIFO Level
#define	AIC_SR_RFL_MASK		(0x3f << AIC_SR_RFL_BIT)
#define	AIC_SR_TFL_BIT		8   // Transmit FIFO level
#define	AIC_SR_TFL_MASK		(0x3f << AIC_SR_TFL_BIT)
#define	AIC_SR_ROR		(1 << 6) // Receive FIFO Overrun
#define	AIC_SR_TUR		(1 << 5) // Transmit FIFO Underrun
#define	AIC_SR_RFS		(1 << 4) // Receive FIFO Service Request
#define	AIC_SR_TFS		(1 << 3) // Transmit FIFO Service Request

// AIC Controller AC-link Status Register (AIC_ACSR)

#define	AIC_ACSR_SLTERR		(1 << 21) // Slot Error Flag
#define	AIC_ACSR_CRDY		(1 << 20) // External CODEC Ready Flag
#define	AIC_ACSR_CLPM		(1 << 19) // External CODEC low power mode flag
#define	AIC_ACSR_RSTO		(1 << 18) // External CODEC regs read status timeout
#define	AIC_ACSR_SADR		(1 << 17) // External CODEC regs status addr and data received
#define	AIC_ACSR_CADT		(1 << 16) // Command Address and Data Transmitted

// AIC Controller I2S/MSB-justified Status Register (AIC_I2SSR)

#define	AIC_I2SSR_BSY		(1 << 2)  // AIC Busy in I2S/MSB-justified format

// AIC Controller AC97 codec Command Address Register (AIC_ACCAR)

#define	AIC_ACCAR_CAR_BIT	0
#define	AIC_ACCAR_CAR_MASK	(0xfffff << AIC_ACCAR_CAR_BIT)

// AIC Controller AC97 codec Command Data Register (AIC_ACCDR)

#define	AIC_ACCDR_CDR_BIT	0
#define	AIC_ACCDR_CDR_MASK	(0xfffff << AIC_ACCDR_CDR_BIT)

// AIC Controller AC97 codec Status Address Register (AIC_ACSAR)

#define	AIC_ACSAR_SAR_BIT	0
#define	AIC_ACSAR_SAR_MASK	(0xfffff << AIC_ACSAR_SAR_BIT)

// AIC Controller AC97 codec Status Data Register (AIC_ACSDR)

#define	AIC_ACSDR_SDR_BIT	0
#define	AIC_ACSDR_SDR_MASK	(0xfffff << AIC_ACSDR_SDR_BIT)

// AIC Controller I2S/MSB-justified Clock Divider Register (AIC_I2SDIV)

#define	AIC_I2SDIV_DIV_BIT	0
#define	AIC_I2SDIV_DIV_MASK	(0x7f << AIC_I2SDIV_DIV_BIT)
  #define AIC_I2SDIV_BITCLK_3072KHZ	(0x0C << AIC_I2SDIV_DIV_BIT) // BIT_CLK of 3.072MHz
  #define AIC_I2SDIV_BITCLK_2836KHZ	(0x0D << AIC_I2SDIV_DIV_BIT) // BIT_CLK of 2.836MHz
  #define AIC_I2SDIV_BITCLK_1418KHZ	(0x1A << AIC_I2SDIV_DIV_BIT) // BIT_CLK of 1.418MHz
  #define AIC_I2SDIV_BITCLK_1024KHZ	(0x24 << AIC_I2SDIV_DIV_BIT) // BIT_CLK of 1.024MHz
  #define AIC_I2SDIV_BITCLK_7089KHZ	(0x34 << AIC_I2SDIV_DIV_BIT) // BIT_CLK of 708.92KHz
  #define AIC_I2SDIV_BITCLK_512KHZ	(0x48 << AIC_I2SDIV_DIV_BIT) // BIT_CLK of 512.00KHz


//************************************************************************
// ICDC (Internal CODEC)
//************************************************************************
#define	ICDC_CR			REG32 (ICDC_BASE + 0x0400)  // ICDC Control Register
#define	ICDC_APWAIT		REG32 (ICDC_BASE + 0x0404)  // Anti-Pop WAIT Stage Timing Control Register
#define	ICDC_APPRE		REG32 (ICDC_BASE + 0x0408)  // Anti-Pop HPEN-PRE Stage Timing Control Register
#define	ICDC_APHPEN		REG32 (ICDC_BASE + 0x040C)  // Anti-Pop HPEN Stage Timing Control Register
#define	ICDC_APSR		REG32 (ICDC_BASE + 0x0410)  // Anti-Pop Status Register
#define ICDC_CDCCR1		REG32 (ICDC_BASE + 0x0080)
#define ICDC_CDCCR2		REG32 (ICDC_BASE + 0x0084)

// ICDC Control Register
#define	ICDC_CR_LINVOL_BIT	24 // LINE Input Volume Gain: GAIN=LINVOL*1.5-34.5
#define	ICDC_CR_LINVOL_MASK	(0x1f << ICDC_CR_LINVOL_BIT)
#define	ICDC_CR_ASRATE_BIT	20 // Audio Sample Rate
#define	ICDC_CR_ASRATE_MASK	(0x0f << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_8000	(0x0 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_11025	(0x1 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_12000	(0x2 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_16000	(0x3 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_22050	(0x4 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_24000	(0x5 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_32000	(0x6 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_44100	(0x7 << ICDC_CR_ASRATE_BIT)
  #define ICDC_CR_ASRATE_48000	(0x8 << ICDC_CR_ASRATE_BIT)
#define	ICDC_CR_MICBG_BIT	18 // MIC Boost Gain
#define	ICDC_CR_MICBG_MASK	(0x3 << ICDC_CR_MICBG_BIT)
  #define ICDC_CR_MICBG_0DB	(0x0 << ICDC_CR_MICBG_BIT)
  #define ICDC_CR_MICBG_6DB	(0x1 << ICDC_CR_MICBG_BIT)
  #define ICDC_CR_MICBG_12DB	(0x2 << ICDC_CR_MICBG_BIT)
  #define ICDC_CR_MICBG_20DB	(0x3 << ICDC_CR_MICBG_BIT)
#define	ICDC_CR_HPVOL_BIT	16 // Headphone Volume Gain
#define	ICDC_CR_HPVOL_MASK	(0x3 << ICDC_CR_HPVOL_BIT)
  #define ICDC_CR_HPVOL_0DB	(0x0 << ICDC_CR_HPVOL_BIT)
  #define ICDC_CR_HPVOL_2DB	(0x1 << ICDC_CR_HPVOL_BIT)
  #define ICDC_CR_HPVOL_4DB	(0x2 << ICDC_CR_HPVOL_BIT)
  #define ICDC_CR_HPVOL_6DB	(0x3 << ICDC_CR_HPVOL_BIT)
#define ICDC_CR_ELINEIN		(1 << 13) // Enable LINE Input
#define ICDC_CR_EMIC		(1 << 12) // Enable MIC Input
#define ICDC_CR_SW1ON		(1 << 11) // Switch 1 in CODEC is on
#define ICDC_CR_EADC		(1 << 10) // Enable ADC
#define ICDC_CR_SW2ON		(1 << 9)  // Switch 2 in CODEC is on
#define ICDC_CR_EDAC		(1 << 8)  // Enable DAC
#define ICDC_CR_HPMUTE		(1 << 5)  // Headphone Mute
#define ICDC_CR_HPTON		(1 << 4)  // Headphone Amplifier Trun On
#define ICDC_CR_HPTOFF		(1 << 3)  // Headphone Amplifier Trun Off
#define ICDC_CR_TAAP		(1 << 2)  // Turn Around of the Anti-Pop Procedure
#define ICDC_CR_EAP		(1 << 1)  // Enable Anti-Pop Procedure
#define ICDC_CR_SUSPD		(1 << 0)  // CODEC Suspend

// Anti-Pop WAIT Stage Timing Control Register
#define	ICDC_APWAIT_WAITSN_BIT	0
#define	ICDC_APWAIT_WAITSN_MASK	(0x7ff << ICDC_APWAIT_WAITSN_BIT)

// Anti-Pop HPEN-PRE Stage Timing Control Register
#define	ICDC_APPRE_PRESN_BIT	0
#define	ICDC_APPRE_PRESN_MASK	(0x1ff << ICDC_APPRE_PRESN_BIT)

// Anti-Pop HPEN Stage Timing Control Register
#define	ICDC_APHPEN_HPENSN_BIT	0
#define	ICDC_APHPEN_HPENSN_MASK	(0x3fff << ICDC_APHPEN_HPENSN_BIT)

// Anti-Pop Status Register
#define	ICDC_SR_HPST_BIT	14  // Headphone Amplifier State
#define	ICDC_SR_HPST_MASK	(0x7 << ICDC_SR_HPST_BIT)
#define ICDC_SR_HPST_HP_OFF	 (0x0 << ICDC_SR_HPST_BIT) // HP amplifier is off
#define ICDC_SR_HPST_TON_WAIT	 (0x1 << ICDC_SR_HPST_BIT) // wait state in turn-on
  #define ICDC_SR_HPST_TON_PRE	 (0x2 << ICDC_SR_HPST_BIT) // pre-enable state in turn-on
#define ICDC_SR_HPST_TON_HPEN	 (0x3 << ICDC_SR_HPST_BIT) // HP enable state in turn-on
  #define ICDC_SR_HPST_TOFF_HPEN (0x4 << ICDC_SR_HPST_BIT) // HP enable state in turn-off
  #define ICDC_SR_HPST_TOFF_PRE  (0x5 << ICDC_SR_HPST_BIT) // pre-enable state in turn-off
  #define ICDC_SR_HPST_TOFF_WAIT (0x6 << ICDC_SR_HPST_BIT) // wait state in turn-off
  #define ICDC_SR_HPST_HP_ON	 (0x7 << ICDC_SR_HPST_BIT) // HP amplifier is on
#define	ICDC_SR_SNCNT_BIT	0  // Sample Number Counter
#define	ICDC_SR_SNCNT_MASK	(0x3fff << ICDC_SR_SNCNT_BIT)


//************************************************************************
// I2C
//************************************************************************
#define	I2C_DR			REG8 (I2C_BASE + 0x000)
#define	I2C_CR			REG8 (I2C_BASE + 0x004)
#define	I2C_SR			REG8 (I2C_BASE + 0x008)
#define	I2C_GR			REG16 (I2C_BASE + 0x00C)

// I2C Control Register (I2C_CR)

#define I2C_CR_IEN		(1 << 4)
#define I2C_CR_STA		(1 << 3)
#define I2C_CR_STO		(1 << 2)
#define I2C_CR_AC		(1 << 1)
#define I2C_CR_I2CE		(1 << 0)

// I2C Status Register (I2C_SR)

#define I2C_SR_STX		(1 << 4)
#define I2C_SR_BUSY		(1 << 3)
#define I2C_SR_TEND		(1 << 2)
#define I2C_SR_DRF		(1 << 1)
#define I2C_SR_ACKF		(1 << 0)


//************************************************************************
// SSI
//************************************************************************
#define	SSI_DR			REG32 (SSI_BASE + 0x000)
#define	SSI_CR0			REG16 (SSI_BASE + 0x004)
#define	SSI_CR1			REG32 (SSI_BASE + 0x008)
#define	SSI_SR			REG32 (SSI_BASE + 0x00C)
#define	SSI_ITR			REG16 (SSI_BASE + 0x010)
#define	SSI_ICR			REG8 (SSI_BASE + 0x014)
#define	SSI_GR			REG16 (SSI_BASE + 0x018)

// SSI Data Register (SSI_DR)

#define	SSI_DR_GPC_BIT		0
#define	SSI_DR_GPC_MASK		(0x1ff << SSI_DR_GPC_BIT)

// SSI Control Register 0 (SSI_CR0)

#define SSI_CR0_SSIE		(1 << 15)
#define SSI_CR0_TIE		(1 << 14)
#define SSI_CR0_RIE		(1 << 13)
#define SSI_CR0_TEIE		(1 << 12)
#define SSI_CR0_REIE		(1 << 11)
#define SSI_CR0_LOOP		(1 << 10)
#define SSI_CR0_RFINE		(1 << 9)
#define SSI_CR0_RFINC		(1 << 8)
#define SSI_CR0_FSEL		(1 << 6)
#define SSI_CR0_TFLUSH		(1 << 2)
#define SSI_CR0_RFLUSH		(1 << 1)
#define SSI_CR0_DISREV		(1 << 0)

// SSI Control Register 1 (SSI_CR1)

#define SSI_CR1_FRMHL_BIT	30
#define SSI_CR1_FRMHL_MASK	(0x3 << SSI_CR1_FRMHL_BIT)
  #define SSI_CR1_FRMHL_CELOW_CE2LOW	(0 << SSI_CR1_FRMHL_BIT) // SSI_CE_ is low valid and SSI_CE2_ is low valid
  #define SSI_CR1_FRMHL_CEHIGH_CE2LOW	(1 << SSI_CR1_FRMHL_BIT) // SSI_CE_ is high valid and SSI_CE2_ is low valid
  #define SSI_CR1_FRMHL_CELOW_CE2HIGH	(2 << SSI_CR1_FRMHL_BIT) // SSI_CE_ is low valid  and SSI_CE2_ is high valid
  #define SSI_CR1_FRMHL_CEHIGH_CE2HIGH	(3 << SSI_CR1_FRMHL_BIT) // SSI_CE_ is high valid and SSI_CE2_ is high valid
#define SSI_CR1_TFVCK_BIT	28
#define SSI_CR1_TFVCK_MASK	(0x3 << SSI_CR1_TFVCK_BIT)
  #define SSI_CR1_TFVCK_0	  (0 << SSI_CR1_TFVCK_BIT)
  #define SSI_CR1_TFVCK_1	  (1 << SSI_CR1_TFVCK_BIT)
  #define SSI_CR1_TFVCK_2	  (2 << SSI_CR1_TFVCK_BIT)
  #define SSI_CR1_TFVCK_3	  (3 << SSI_CR1_TFVCK_BIT)
#define SSI_CR1_TCKFI_BIT	26
#define SSI_CR1_TCKFI_MASK	(0x3 << SSI_CR1_TCKFI_BIT)
  #define SSI_CR1_TCKFI_0	  (0 << SSI_CR1_TCKFI_BIT)
  #define SSI_CR1_TCKFI_1	  (1 << SSI_CR1_TCKFI_BIT)
  #define SSI_CR1_TCKFI_2	  (2 << SSI_CR1_TCKFI_BIT)
  #define SSI_CR1_TCKFI_3	  (3 << SSI_CR1_TCKFI_BIT)
#define SSI_CR1_LFST		(1 << 25)
#define SSI_CR1_ITFRM		(1 << 24)
#define SSI_CR1_UNFIN		(1 << 23)
#define SSI_CR1_MULTS		(1 << 22)
#define SSI_CR1_FMAT_BIT	20
#define SSI_CR1_FMAT_MASK	(0x3 << SSI_CR1_FMAT_BIT)
  #define SSI_CR1_FMAT_SPI	  (0 << SSI_CR1_FMAT_BIT) // Motorola's SPI format
  #define SSI_CR1_FMAT_SSP	  (1 << SSI_CR1_FMAT_BIT) // TI's SSP format
  #define SSI_CR1_FMAT_MW1	  (2 << SSI_CR1_FMAT_BIT) // National Microwire 1 format
  #define SSI_CR1_FMAT_MW2	  (3 << SSI_CR1_FMAT_BIT) // National Microwire 2 format
#define SSI_CR1_TTRG_BIT	16
#define SSI_CR1_TTRG_MASK	(0xf << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_1	  (0 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_8	  (1 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_16	  (2 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_24	  (3 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_32	  (4 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_40	  (5 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_48	  (6 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_56	  (7 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_64	  (8 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_72	  (9 << SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_80	  (10<< SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_88	  (11<< SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_96	  (12<< SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_104	  (13<< SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_112	  (14<< SSI_CR1_TTRG_BIT)
  #define SSI_CR1_TTRG_120	  (15<< SSI_CR1_TTRG_BIT)
#define SSI_CR1_MCOM_BIT	12
#define SSI_CR1_MCOM_MASK	(0xf << SSI_CR1_MCOM_BIT)
  #define SSI_CR1_MCOM_1BIT	  (0x0 << SSI_CR1_MCOM_BIT) // 1-bit command selected
  #define SSI_CR1_MCOM_2BIT	  (0x1 << SSI_CR1_MCOM_BIT) // 2-bit command selected
  #define SSI_CR1_MCOM_3BIT	  (0x2 << SSI_CR1_MCOM_BIT) // 3-bit command selected
  #define SSI_CR1_MCOM_4BIT	  (0x3 << SSI_CR1_MCOM_BIT) // 4-bit command selected
  #define SSI_CR1_MCOM_5BIT	  (0x4 << SSI_CR1_MCOM_BIT) // 5-bit command selected
  #define SSI_CR1_MCOM_6BIT	  (0x5 << SSI_CR1_MCOM_BIT) // 6-bit command selected
  #define SSI_CR1_MCOM_7BIT	  (0x6 << SSI_CR1_MCOM_BIT) // 7-bit command selected
  #define SSI_CR1_MCOM_8BIT	  (0x7 << SSI_CR1_MCOM_BIT) // 8-bit command selected
  #define SSI_CR1_MCOM_9BIT	  (0x8 << SSI_CR1_MCOM_BIT) // 9-bit command selected
  #define SSI_CR1_MCOM_10BIT	  (0x9 << SSI_CR1_MCOM_BIT) // 10-bit command selected
  #define SSI_CR1_MCOM_11BIT	  (0xA << SSI_CR1_MCOM_BIT) // 11-bit command selected
  #define SSI_CR1_MCOM_12BIT	  (0xB << SSI_CR1_MCOM_BIT) // 12-bit command selected
  #define SSI_CR1_MCOM_13BIT	  (0xC << SSI_CR1_MCOM_BIT) // 13-bit command selected
  #define SSI_CR1_MCOM_14BIT	  (0xD << SSI_CR1_MCOM_BIT) // 14-bit command selected
  #define SSI_CR1_MCOM_15BIT	  (0xE << SSI_CR1_MCOM_BIT) // 15-bit command selected
  #define SSI_CR1_MCOM_16BIT	  (0xF << SSI_CR1_MCOM_BIT) // 16-bit command selected
#define SSI_CR1_RTRG_BIT	8
#define SSI_CR1_RTRG_MASK	(0xf << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_1	  (0 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_8	  (1 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_16	  (2 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_24	  (3 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_32	  (4 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_40	  (5 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_48	  (6 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_56	  (7 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_64	  (8 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_72	  (9 << SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_80	  (10<< SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_88	  (11<< SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_96	  (12<< SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_104	  (13<< SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_112	  (14<< SSI_CR1_RTRG_BIT)
  #define SSI_CR1_RTRG_120	  (15<< SSI_CR1_RTRG_BIT)
#define SSI_CR1_FLEN_BIT	4
#define SSI_CR1_FLEN_MASK	(0xf << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_2BIT	  (0x0 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_3BIT	  (0x1 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_4BIT	  (0x2 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_5BIT	  (0x3 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_6BIT	  (0x4 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_7BIT	  (0x5 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_8BIT	  (0x6 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_9BIT	  (0x7 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_10BIT	  (0x8 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_11BIT	  (0x9 << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_12BIT	  (0xA << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_13BIT	  (0xB << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_14BIT	  (0xC << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_15BIT	  (0xD << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_16BIT	  (0xE << SSI_CR1_FLEN_BIT)
  #define SSI_CR1_FLEN_17BIT	  (0xF << SSI_CR1_FLEN_BIT)
#define SSI_CR1_PHA		(1 << 1)
#define SSI_CR1_POL		(1 << 0)

// SSI Status Register (SSI_SR)

#define SSI_SR_TFIFONUM_BIT	16
#define SSI_SR_TFIFONUM_MASK	(0xff << SSI_SR_TFIFONUM_BIT)
#define SSI_SR_RFIFONUM_BIT	8
#define SSI_SR_RFIFONUM_MASK	(0xff << SSI_SR_RFIFONUM_BIT)
#define SSI_SR_END		(1 << 7)
#define SSI_SR_BUSY		(1 << 6)
#define SSI_SR_TFF		(1 << 5)
#define SSI_SR_RFE		(1 << 4)
#define SSI_SR_TFHE		(1 << 3)
#define SSI_SR_RFHF		(1 << 2)
#define SSI_SR_UNDR		(1 << 1)
#define SSI_SR_OVER		(1 << 0)

// SSI Interval Time Control Register (SSI_ITR)

#define	SSI_ITR_CNTCLK		(1 << 15)
#define SSI_ITR_IVLTM_BIT	0
#define SSI_ITR_IVLTM_MASK	(0x7fff << SSI_ITR_IVLTM_BIT)


//************************************************************************
// MSC
//************************************************************************
#define	MSC_STRPCL		REG16 (MSC_BASE + 0x000)
#define	MSC_STAT		REG32 (MSC_BASE + 0x004)
#define	MSC_CLKRT		REG16 (MSC_BASE + 0x008)
#define	MSC_CMDAT		REG32 (MSC_BASE + 0x00C)
#define	MSC_RESTO		REG16 (MSC_BASE + 0x010)
#define	MSC_RDTO		REG16 (MSC_BASE + 0x014)
#define	MSC_BLKLEN		REG16 (MSC_BASE + 0x018)
#define	MSC_NOB			REG16 (MSC_BASE + 0x01C)
#define	MSC_SNOB		REG16 (MSC_BASE + 0x020)
#define	MSC_IMASK		REG16 (MSC_BASE + 0x024)
#define	MSC_IREG		REG16 (MSC_BASE + 0x028)
#define	MSC_CMD			REG8 (MSC_BASE + 0x02C)
#define	MSC_ARG			REG32 (MSC_BASE + 0x030)
#define	MSC_RES			REG16 (MSC_BASE + 0x034)
#define	MSC_RXFIFO		REG32 (MSC_BASE + 0x038)
#define	MSC_TXFIFO		REG32 (MSC_BASE + 0x03C)

// MSC Clock and Control Register (MSC_STRPCL)

#define MSC_STRPCL_EXIT_MULTIPLE	(1 << 7)
#define MSC_STRPCL_EXIT_TRANSFER	(1 << 6)
#define MSC_STRPCL_START_READWAIT	(1 << 5)
#define MSC_STRPCL_STOP_READWAIT	(1 << 4)
#define MSC_STRPCL_RESET		(1 << 3)
#define MSC_STRPCL_START_OP		(1 << 2)
#define MSC_STRPCL_CLOCK_CONTROL_BIT	0
#define MSC_STRPCL_CLOCK_CONTROL_MASK	(0x3 << MSC_STRPCL_CLOCK_CONTROL_BIT)
  #define MSC_STRPCL_CLOCK_CONTROL_STOP	  (0x1 << MSC_STRPCL_CLOCK_CONTROL_BIT) // Stop MMC/SD clock
  #define MSC_STRPCL_CLOCK_CONTROL_START  (0x2 << MSC_STRPCL_CLOCK_CONTROL_BIT) // Start MMC/SD clock

// MSC Status Register (MSC_STAT)

#define MSC_STAT_IS_RESETTING		(1 << 15)
#define MSC_STAT_SDIO_INT_ACTIVE	(1 << 14)
#define MSC_STAT_PRG_DONE		(1 << 13)
#define MSC_STAT_DATA_TRAN_DONE		(1 << 12)
#define MSC_STAT_END_CMD_RES		(1 << 11)
#define MSC_STAT_DATA_FIFO_AFULL	(1 << 10)
#define MSC_STAT_IS_READWAIT		(1 << 9)
#define MSC_STAT_CLK_EN			(1 << 8)
#define MSC_STAT_DATA_FIFO_FULL		(1 << 7)
#define MSC_STAT_DATA_FIFO_EMPTY	(1 << 6)
#define MSC_STAT_CRC_RES_ERR		(1 << 5)
#define MSC_STAT_CRC_READ_ERROR		(1 << 4)
#define MSC_STAT_CRC_WRITE_ERROR_BIT	2
#define MSC_STAT_CRC_WRITE_ERROR_MASK	(0x3 << MSC_STAT_CRC_WRITE_ERROR_BIT)
  #define MSC_STAT_CRC_WRITE_ERROR_NO		(0 << MSC_STAT_CRC_WRITE_ERROR_BIT) // No error on transmission of data
  #define MSC_STAT_CRC_WRITE_ERROR		(1 << MSC_STAT_CRC_WRITE_ERROR_BIT) // Card observed erroneous transmission of data
  #define MSC_STAT_CRC_WRITE_ERROR_NOSTS	(2 << MSC_STAT_CRC_WRITE_ERROR_BIT) // No CRC status is sent back
#define MSC_STAT_TIME_OUT_RES		(1 << 1)
#define MSC_STAT_TIME_OUT_READ		(1 << 0)

// MSC Bus Clock Control Register (MSC_CLKRT)

#define	MSC_CLKRT_CLK_RATE_BIT		0
#define	MSC_CLKRT_CLK_RATE_MASK		(0x7 << MSC_CLKRT_CLK_RATE_BIT)
  #define MSC_CLKRT_CLK_RATE_DIV_1	  (0x0 << MSC_CLKRT_CLK_RATE_BIT) // CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_2	  (0x1 << MSC_CLKRT_CLK_RATE_BIT) // 1/2 of CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_4	  (0x2 << MSC_CLKRT_CLK_RATE_BIT) // 1/4 of CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_8	  (0x3 << MSC_CLKRT_CLK_RATE_BIT) // 1/8 of CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_16	  (0x4 << MSC_CLKRT_CLK_RATE_BIT) // 1/16 of CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_32	  (0x5 << MSC_CLKRT_CLK_RATE_BIT) // 1/32 of CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_64	  (0x6 << MSC_CLKRT_CLK_RATE_BIT) // 1/64 of CLK_SRC
  #define MSC_CLKRT_CLK_RATE_DIV_128	  (0x7 << MSC_CLKRT_CLK_RATE_BIT) // 1/128 of CLK_SRC

// MSC Command Sequence Control Register (MSC_CMDAT)

#define	MSC_CMDAT_IO_ABORT		(1 << 11)
#define	MSC_CMDAT_BUS_WIDTH_BIT		9
#define	MSC_CMDAT_BUS_WIDTH_MASK	(0x3 << MSC_CMDAT_BUS_WIDTH_BIT)
  #define MSC_CMDAT_BUS_WIDTH_1BIT	  (0x0 << MSC_CMDAT_BUS_WIDTH_BIT) // 1-bit data bus
  #define MSC_CMDAT_BUS_WIDTH_4BIT	  (0x2 << MSC_CMDAT_BUS_WIDTH_BIT) // 4-bit data bus
#define	MSC_CMDAT_DMA_EN		(1 << 8)
#define	MSC_CMDAT_INIT			(1 << 7)
#define	MSC_CMDAT_BUSY			(1 << 6)
#define	MSC_CMDAT_STREAM_BLOCK		(1 << 5)
#define	MSC_CMDAT_WRITE			(1 << 4)
#define	MSC_CMDAT_READ			(0 << 4)
#define	MSC_CMDAT_DATA_EN		(1 << 3)
#define	MSC_CMDAT_RESPONSE_BIT	0
#define	MSC_CMDAT_RESPONSE_MASK	(0x7 << MSC_CMDAT_RESPONSE_BIT)
  #define MSC_CMDAT_RESPONSE_NONE  (0x0 << MSC_CMDAT_RESPONSE_BIT) // No response
  #define MSC_CMDAT_RESPONSE_R1	  (0x1 << MSC_CMDAT_RESPONSE_BIT) // Format R1 and R1b
  #define MSC_CMDAT_RESPONSE_R2	  (0x2 << MSC_CMDAT_RESPONSE_BIT) // Format R2
  #define MSC_CMDAT_RESPONSE_R3	  (0x3 << MSC_CMDAT_RESPONSE_BIT) // Format R3
  #define MSC_CMDAT_RESPONSE_R4	  (0x4 << MSC_CMDAT_RESPONSE_BIT) // Format R4
  #define MSC_CMDAT_RESPONSE_R5	  (0x5 << MSC_CMDAT_RESPONSE_BIT) // Format R5
  #define MSC_CMDAT_RESPONSE_R6	  (0x6 << MSC_CMDAT_RESPONSE_BIT) // Format R6
  #define MSC_CMDAT_RESPONSE_R7	  (0x7 << MSC_CMDAT_RESPONSE_BIT) // Format R7

#define	MSC_CMDAT_DMA_EN	(1 << 8)
#define	MSC_CMDAT_INIT		(1 << 7)
#define	MSC_CMDAT_BUSY		(1 << 6)
#define	MSC_CMDAT_STREAM	(1 << 5)
#define	MSC_CMDAT_WRITE		(1 << 4)
#define	MSC_CMDAT_DATA_EN	(1 << 3)

// MSC Interrupts Mask Register (MSC_IMASK)

#define	MSC_IMASK_SDIO			(1 << 7)
#define	MSC_IMASK_TXFIFO_WR_REQ		(1 << 6)
#define	MSC_IMASK_RXFIFO_RD_REQ		(1 << 5)
#define	MSC_IMASK_END_CMD_RES		(1 << 2)
#define	MSC_IMASK_PRG_DONE		(1 << 1)
#define	MSC_IMASK_DATA_TRAN_DONE	(1 << 0)


// MSC Interrupts Status Register (MSC_IREG)

#define	MSC_IREG_SDIO			(1 << 7)
#define	MSC_IREG_TXFIFO_WR_REQ		(1 << 6)
#define	MSC_IREG_RXFIFO_RD_REQ		(1 << 5)
#define	MSC_IREG_END_CMD_RES		(1 << 2)
#define	MSC_IREG_PRG_DONE		(1 << 1)
#define	MSC_IREG_DATA_TRAN_DONE		(1 << 0)


//************************************************************************
// EMC (External Memory Controller)
//************************************************************************
#define EMC_SMCR(n)	REG32 (EMC_BASE + 0x10 + 4 * (n))  // Static Memory Control Register n (n = 0,1,2,3,4)
#define EMC_SACR(n)	REG32 (EMC_BASE + 0x30 + 4 * (n))  // Static Memory Bank n Addr Config Reg (n = 0,1,2,3,4)

#define EMC_NFCSR	REG32 (EMC_BASE + 0x050) // NAND Flash Control/Status Register
#define EMC_NFECR	REG32 (EMC_BASE + 0x100) // NAND Flash ECC Control Register
#define EMC_NFECC	REG32 (EMC_BASE + 0x104) // NAND Flash ECC Data Register
#define EMC_NFPAR(n)	REG32 (EMC_BASE + 0x108 + 4 * (n)) // NAND Flash RS Parity n Register (n = 0,1,2)
#define EMC_NFINTS	REG32 (EMC_BASE + 0x114) // NAND Flash Interrupt Status Register
#define EMC_NFINTE	REG32 (EMC_BASE + 0x118) // NAND Flash Interrupt Enable Register
#define EMC_NFERR(n)	REG32 (EMC_BASE + 0x11c + 4 * (n)) // NAND Flash RS Error Report n Register (n = 0,1,2,3)

#define EMC_DMCR	REG32 (EMC_BASE + 0x80)  // DRAM Control Register
#define EMC_RTCSR	REG16 (EMC_BASE + 0x84)  // Refresh Time Control/Status Register
#define EMC_RTCNT	REG16 (EMC_BASE + 0x88)  // Refresh Timer Counter
#define EMC_RTCOR	REG16 (EMC_BASE + 0x8c)  // Refresh Time Constant Register
#define EMC_DMAR0	REG32 (EMC_BASE + 0x90)  // SDRAM Bank 0 Addr Config Register
#define EMC_SDMR0	(EMC_BASE + 0xa000) // Mode Register of SDRAM bank 0.  Very weird: uses address bus for data.  Data bus is ignored, thus no REG
#define EMC_BCR		REG32 (EMC_BASE + 0x00)	// Bus Control Register

// Static Memory Control Register
#define EMC_SMCR_STRV_BIT	24
#define EMC_SMCR_STRV_MASK	(0x0f << EMC_SMCR_STRV_BIT)
#define EMC_SMCR_TAW_BIT	20
#define EMC_SMCR_TAW_MASK	(0x0f << EMC_SMCR_TAW_BIT)
#define EMC_SMCR_TBP_BIT	16
#define EMC_SMCR_TBP_MASK	(0x0f << EMC_SMCR_TBP_BIT)
#define EMC_SMCR_TAH_BIT	12
#define EMC_SMCR_TAH_MASK	(0x07 << EMC_SMCR_TAH_BIT)
#define EMC_SMCR_TAS_BIT	8
#define EMC_SMCR_TAS_MASK	(0x07 << EMC_SMCR_TAS_BIT)
#define EMC_SMCR_BW_BIT		6
#define EMC_SMCR_BW_MASK	(0x03 << EMC_SMCR_BW_BIT)
  #define EMC_SMCR_BW_8BIT	(0 << EMC_SMCR_BW_BIT)
  #define EMC_SMCR_BW_16BIT	(1 << EMC_SMCR_BW_BIT)
  #define EMC_SMCR_BW_32BIT	(2 << EMC_SMCR_BW_BIT)
#define EMC_SMCR_BCM		(1 << 3)
#define EMC_SMCR_BL_BIT		1
#define EMC_SMCR_BL_MASK	(0x03 << EMC_SMCR_BL_BIT)
  #define EMC_SMCR_BL_4		(0 << EMC_SMCR_BL_BIT)
  #define EMC_SMCR_BL_8		(1 << EMC_SMCR_BL_BIT)
  #define EMC_SMCR_BL_16	(2 << EMC_SMCR_BL_BIT)
  #define EMC_SMCR_BL_32	(3 << EMC_SMCR_BL_BIT)
#define EMC_SMCR_SMT		(1 << 0)

// Static Memory Bank Addr Config Reg
#define EMC_SACR_BASE_BIT	8
#define EMC_SACR_BASE_MASK	(0xff << EMC_SACR_BASE_BIT)
#define EMC_SACR_MASK_BIT	0
#define EMC_SACR_MASK_MASK	(0xff << EMC_SACR_MASK_BIT)

// NAND Flash Control/Status Register
#define EMC_NFCSR_NFCE4		(1 << 7) // NAND Flash Enable
#define EMC_NFCSR_NFE4		(1 << 6) // NAND Flash FCE# Assertion Enable
#define EMC_NFCSR_NFCE3		(1 << 5)
#define EMC_NFCSR_NFE3		(1 << 4)
#define EMC_NFCSR_NFCE2		(1 << 3)
#define EMC_NFCSR_NFE2		(1 << 2)
#define EMC_NFCSR_NFCE1		(1 << 1)
#define EMC_NFCSR_NFE1		(1 << 0)

// NAND Flash ECC Control Register
#define EMC_NFECR_PRDY		(1 << 4) // Parity Ready
#define EMC_NFECR_RS_DECODING	(0 << 3) // RS is in decoding phase
#define EMC_NFECR_RS_ENCODING	(1 << 3) // RS is in encoding phase
#define EMC_NFECR_HAMMING	(0 << 2) // Select HAMMING Correction Algorithm
#define EMC_NFECR_RS		(1 << 2) // Select RS Correction Algorithm
#define EMC_NFECR_ERST		(1 << 1) // ECC Reset
#define EMC_NFECR_ECCE		(1 << 0) // ECC Enable

// NAND Flash ECC Data Register
#define EMC_NFECC_ECC2_BIT	16
#define EMC_NFECC_ECC2_MASK	(0xff << EMC_NFECC_ECC2_BIT)
#define EMC_NFECC_ECC1_BIT	8
#define EMC_NFECC_ECC1_MASK	(0xff << EMC_NFECC_ECC1_BIT)
#define EMC_NFECC_ECC0_BIT	0
#define EMC_NFECC_ECC0_MASK	(0xff << EMC_NFECC_ECC0_BIT)

// NAND Flash Interrupt Status Register
#define EMC_NFINTS_ERRCNT_BIT	29       // Error Count
#define EMC_NFINTS_ERRCNT_MASK	(0x7 << EMC_NFINTS_ERRCNT_BIT)
#define EMC_NFINTS_PADF		(1 << 4) // Padding Finished
#define EMC_NFINTS_DECF		(1 << 3) // Decoding Finished
#define EMC_NFINTS_ENCF		(1 << 2) // Encoding Finished
#define EMC_NFINTS_UNCOR	(1 << 1) // Uncorrectable Error Occurred
#define EMC_NFINTS_ERR		(1 << 0) // Error Occurred

// NAND Flash Interrupt Enable Register
#define EMC_NFINTE_PADFE	(1 << 4) // Padding Finished Interrupt Enable
#define EMC_NFINTE_DECFE	(1 << 3) // Decoding Finished Interrupt Enable
#define EMC_NFINTE_ENCFE	(1 << 2) // Encoding Finished Interrupt Enable
#define EMC_NFINTE_UNCORE	(1 << 1) // Uncorrectable Error Occurred Intr Enable
#define EMC_NFINTE_ERRE		(1 << 0) // Error Occurred Interrupt

// NAND Flash RS Error Report Register
#define EMC_NFERR_INDEX_BIT	16       // Error Symbol Index
#define EMC_NFERR_INDEX_MASK	(0x1ff << EMC_NFERR_INDEX_BIT)
#define EMC_NFERR_MASK_BIT	0        // Error Symbol Value
#define EMC_NFERR_MASK_MASK	(0x1ff << EMC_NFERR_MASK_BIT)


// DRAM Control Register
#define EMC_DMCR_BW_BIT		31
#define EMC_DMCR_BW		(1 << EMC_DMCR_BW_BIT)
#define EMC_DMCR_CA_BIT		26
#define EMC_DMCR_CA_MASK	(0x07 << EMC_DMCR_CA_BIT)
  #define EMC_DMCR_CA_8		(0 << EMC_DMCR_CA_BIT)
  #define EMC_DMCR_CA_9		(1 << EMC_DMCR_CA_BIT)
  #define EMC_DMCR_CA_10	(2 << EMC_DMCR_CA_BIT)
  #define EMC_DMCR_CA_11	(3 << EMC_DMCR_CA_BIT)
  #define EMC_DMCR_CA_12	(4 << EMC_DMCR_CA_BIT)
#define EMC_DMCR_RMODE		(1 << 25)
#define EMC_DMCR_RFSH		(1 << 24)
#define EMC_DMCR_MRSET		(1 << 23)
#define EMC_DMCR_RA_BIT		20
#define EMC_DMCR_RA_MASK	(0x03 << EMC_DMCR_RA_BIT)
  #define EMC_DMCR_RA_11	(0 << EMC_DMCR_RA_BIT)
  #define EMC_DMCR_RA_12	(1 << EMC_DMCR_RA_BIT)
  #define EMC_DMCR_RA_13	(2 << EMC_DMCR_RA_BIT)
#define EMC_DMCR_BA_BIT		19
#define EMC_DMCR_BA		(1 << EMC_DMCR_BA_BIT)
#define EMC_DMCR_PDM		(1 << 18)
#define EMC_DMCR_EPIN		(1 << 17)
#define EMC_DMCR_TRAS_BIT	13
#define EMC_DMCR_TRAS_MASK	(0x07 << EMC_DMCR_TRAS_BIT)
#define EMC_DMCR_RCD_BIT	11
#define EMC_DMCR_RCD_MASK	(0x03 << EMC_DMCR_RCD_BIT)
#define EMC_DMCR_TPC_BIT	8
#define EMC_DMCR_TPC_MASK	(0x07 << EMC_DMCR_TPC_BIT)
#define EMC_DMCR_TRWL_BIT	5
#define EMC_DMCR_TRWL_MASK	(0x03 << EMC_DMCR_TRWL_BIT)
#define EMC_DMCR_TRC_BIT	2
#define EMC_DMCR_TRC_MASK	(0x07 << EMC_DMCR_TRC_BIT)
#define EMC_DMCR_TCL_BIT	0
#define EMC_DMCR_TCL_MASK	(0x03 << EMC_DMCR_TCL_BIT)

// Refresh Time Control/Status Register
#define EMC_RTCSR_CMF		(1 << 7)
#define EMC_RTCSR_CKS_BIT	0
#define EMC_RTCSR_CKS_MASK	(0x07 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_DISABLE	(0 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_4	(1 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_16	(2 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_64	(3 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_256	(4 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_1024	(5 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_2048	(6 << EMC_RTCSR_CKS_BIT)
  #define EMC_RTCSR_CKS_4096	(7 << EMC_RTCSR_CKS_BIT)

// SDRAM Bank Address Configuration Register
#define EMC_DMAR_BASE_BIT	8
#define EMC_DMAR_BASE_MASK	(0xff << EMC_DMAR_BASE_BIT)
#define EMC_DMAR_MASK_BIT	0
#define EMC_DMAR_MASK_MASK	(0xff << EMC_DMAR_MASK_BIT)

// Mode Register of SDRAM bank 0
#define EMC_SDMR_BM		(1 << 9) // Write Burst Mode
#define EMC_SDMR_OM_BIT		7        // Operating Mode
#define EMC_SDMR_OM_MASK	(3 << EMC_SDMR_OM_BIT)
  #define EMC_SDMR_OM_NORMAL	(0 << EMC_SDMR_OM_BIT)
#define EMC_SDMR_CAS_BIT	4        // CAS Latency
#define EMC_SDMR_CAS_MASK	(7 << EMC_SDMR_CAS_BIT)
  #define EMC_SDMR_CAS_1	(1 << EMC_SDMR_CAS_BIT)
  #define EMC_SDMR_CAS_2	(2 << EMC_SDMR_CAS_BIT)
  #define EMC_SDMR_CAS_3	(3 << EMC_SDMR_CAS_BIT)
#define EMC_SDMR_BT_BIT		3        // Burst Type
#define EMC_SDMR_BT_MASK	(1 << EMC_SDMR_BT_BIT)
  #define EMC_SDMR_BT_SEQ	(0 << EMC_SDMR_BT_BIT) // Sequential
  #define EMC_SDMR_BT_INT	(1 << EMC_SDMR_BT_BIT) // Interleave
#define EMC_SDMR_BL_BIT		0        // Burst Length
#define EMC_SDMR_BL_MASK	(7 << EMC_SDMR_BL_BIT)
  #define EMC_SDMR_BL_1		(0 << EMC_SDMR_BL_BIT)
  #define EMC_SDMR_BL_2		(1 << EMC_SDMR_BL_BIT)
  #define EMC_SDMR_BL_4		(2 << EMC_SDMR_BL_BIT)
  #define EMC_SDMR_BL_8		(3 << EMC_SDMR_BL_BIT)

#define EMC_SDMR_CAS2_16BIT (EMC_SDMR_CAS_2 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_2)
#define EMC_SDMR_CAS2_32BIT (EMC_SDMR_CAS_2 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_4)
#define EMC_SDMR_CAS3_16BIT (EMC_SDMR_CAS_3 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_2)
#define EMC_SDMR_CAS3_32BIT (EMC_SDMR_CAS_3 | EMC_SDMR_BT_SEQ | EMC_SDMR_BL_4)


//************************************************************************
// CIM
//************************************************************************
#define	CIM_CFG			REG32 (CIM_BASE + 0x0000)
#define	CIM_CTRL		REG32 (CIM_BASE + 0x0004)
#define	CIM_STATE		REG32 (CIM_BASE + 0x0008)
#define	CIM_IID			REG32 (CIM_BASE + 0x000C)
#define	CIM_RXFIFO		REG32 (CIM_BASE + 0x0010)
#define	CIM_DA			REG32 (CIM_BASE + 0x0020)
#define	CIM_FA			REG32 (CIM_BASE + 0x0024)
#define	CIM_FID			REG32 (CIM_BASE + 0x0028)
#define	CIM_CMD			REG32 (CIM_BASE + 0x002C)

// CIM Configuration Register  (CIM_CFG)

#define	CIM_CFG_INV_DAT		(1 << 15)
#define	CIM_CFG_VSP		(1 << 14)
#define	CIM_CFG_HSP		(1 << 13)
#define	CIM_CFG_PCP		(1 << 12)
#define	CIM_CFG_DUMMY_ZERO	(1 << 9)
#define	CIM_CFG_EXT_VSYNC	(1 << 8)
#define	CIM_CFG_PACK_BIT	4
#define	CIM_CFG_PACK_MASK	(0x7 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_0	  (0 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_1	  (1 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_2	  (2 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_3	  (3 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_4	  (4 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_5	  (5 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_6	  (6 << CIM_CFG_PACK_BIT)
  #define CIM_CFG_PACK_7	  (7 << CIM_CFG_PACK_BIT)
#define	CIM_CFG_DSM_BIT		0
#define	CIM_CFG_DSM_MASK	(0x3 << CIM_CFG_DSM_BIT)
  #define CIM_CFG_DSM_CPM	  (0 << CIM_CFG_DSM_BIT) // CCIR656 Progressive Mode
  #define CIM_CFG_DSM_CIM	  (1 << CIM_CFG_DSM_BIT) // CCIR656 Interlace Mode
  #define CIM_CFG_DSM_GCM	  (2 << CIM_CFG_DSM_BIT) // Gated Clock Mode
  #define CIM_CFG_DSM_NGCM	  (3 << CIM_CFG_DSM_BIT) // Non-Gated Clock Mode

// CIM Control Register  (CIM_CTRL)

#define	CIM_CTRL_MCLKDIV_BIT	24
#define	CIM_CTRL_MCLKDIV_MASK	(0xff << CIM_CTRL_MCLKDIV_BIT)
#define	CIM_CTRL_FRC_BIT	16
#define	CIM_CTRL_FRC_MASK	(0xf << CIM_CTRL_FRC_BIT)
  #define CIM_CTRL_FRC_1	  (0x0 << CIM_CTRL_FRC_BIT) // Sample every frame
  #define CIM_CTRL_FRC_2	  (0x1 << CIM_CTRL_FRC_BIT) // Sample 1/2 frame
  #define CIM_CTRL_FRC_3	  (0x2 << CIM_CTRL_FRC_BIT) // Sample 1/3 frame
  #define CIM_CTRL_FRC_4	  (0x3 << CIM_CTRL_FRC_BIT) // Sample 1/4 frame
  #define CIM_CTRL_FRC_5	  (0x4 << CIM_CTRL_FRC_BIT) // Sample 1/5 frame
  #define CIM_CTRL_FRC_6	  (0x5 << CIM_CTRL_FRC_BIT) // Sample 1/6 frame
  #define CIM_CTRL_FRC_7	  (0x6 << CIM_CTRL_FRC_BIT) // Sample 1/7 frame
  #define CIM_CTRL_FRC_8	  (0x7 << CIM_CTRL_FRC_BIT) // Sample 1/8 frame
  #define CIM_CTRL_FRC_9	  (0x8 << CIM_CTRL_FRC_BIT) // Sample 1/9 frame
  #define CIM_CTRL_FRC_10	  (0x9 << CIM_CTRL_FRC_BIT) // Sample 1/10 frame
  #define CIM_CTRL_FRC_11	  (0xA << CIM_CTRL_FRC_BIT) // Sample 1/11 frame
  #define CIM_CTRL_FRC_12	  (0xB << CIM_CTRL_FRC_BIT) // Sample 1/12 frame
  #define CIM_CTRL_FRC_13	  (0xC << CIM_CTRL_FRC_BIT) // Sample 1/13 frame
  #define CIM_CTRL_FRC_14	  (0xD << CIM_CTRL_FRC_BIT) // Sample 1/14 frame
  #define CIM_CTRL_FRC_15	  (0xE << CIM_CTRL_FRC_BIT) // Sample 1/15 frame
  #define CIM_CTRL_FRC_16	  (0xF << CIM_CTRL_FRC_BIT) // Sample 1/16 frame
#define	CIM_CTRL_VDDM		(1 << 13)
#define	CIM_CTRL_DMA_SOFM	(1 << 12)
#define	CIM_CTRL_DMA_EOFM	(1 << 11)
#define	CIM_CTRL_DMA_STOPM	(1 << 10)
#define	CIM_CTRL_RXF_TRIGM	(1 << 9)
#define	CIM_CTRL_RXF_OFM	(1 << 8)
#define	CIM_CTRL_RXF_TRIG_BIT	4
#define	CIM_CTRL_RXF_TRIG_MASK	(0x7 << CIM_CTRL_RXF_TRIG_BIT)
  #define CIM_CTRL_RXF_TRIG_4	  (0 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 4
  #define CIM_CTRL_RXF_TRIG_8	  (1 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 8
  #define CIM_CTRL_RXF_TRIG_12	  (2 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 12
  #define CIM_CTRL_RXF_TRIG_16	  (3 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 16
  #define CIM_CTRL_RXF_TRIG_20	  (4 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 20
  #define CIM_CTRL_RXF_TRIG_24	  (5 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 24
  #define CIM_CTRL_RXF_TRIG_28	  (6 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 28
  #define CIM_CTRL_RXF_TRIG_32	  (7 << CIM_CTRL_RXF_TRIG_BIT) // RXFIFO Trigger Value is 32
#define	CIM_CTRL_DMA_EN		(1 << 2)
#define	CIM_CTRL_RXF_RST	(1 << 1)
#define	CIM_CTRL_ENA		(1 << 0)

// CIM State Register  (CIM_STATE)

#define	CIM_STATE_DMA_SOF	(1 << 6)
#define	CIM_STATE_DMA_EOF	(1 << 5)
#define	CIM_STATE_DMA_STOP	(1 << 4)
#define	CIM_STATE_RXF_OF	(1 << 3)
#define	CIM_STATE_RXF_TRIG	(1 << 2)
#define	CIM_STATE_RXF_EMPTY	(1 << 1)
#define	CIM_STATE_VDD		(1 << 0)

// CIM DMA Command Register (CIM_CMD)

#define	CIM_CMD_SOFINT		(1 << 31)
#define	CIM_CMD_EOFINT		(1 << 30)
#define	CIM_CMD_STOP		(1 << 28)
#define	CIM_CMD_LEN_BIT		0
#define	CIM_CMD_LEN_MASK	(0xffffff << CIM_CMD_LEN_BIT)


//************************************************************************
// SADC (Smart A/D Controller)
//************************************************************************

#define SADC_ENA	REG8 (SADC_BASE + 0x00)  // ADC Enable Register
#define SADC_CFG	REG32 (SADC_BASE + 0x04)  // ADC Configure Register
#define SADC_CTRL	REG8 (SADC_BASE + 0x08)  // ADC Control Register
#define SADC_STATE	REG8 (SADC_BASE + 0x0C)  // ADC Status Register*/
#define SADC_SAMETIME	REG16 (SADC_BASE + 0x10)  // ADC Same Point Time Register
#define SADC_WAITTIME	REG16 (SADC_BASE + 0x14)  // ADC Wait Time Register
#define SADC_TSDAT	REG32 (SADC_BASE + 0x18)  // ADC Touch Screen Data Register
#define SADC_BATDAT	REG16 (SADC_BASE + 0x1C)  // ADC PBAT Data Register
#define SADC_SADDAT	REG16 (SADC_BASE + 0x20)  // ADC SADCIN Data Register

// ADC Enable Register
#define SADC_ENA_ADEN		(1 << 7)  // Touch Screen Enable
#define SADC_ENA_TSEN		(1 << 2)  // Touch Screen Enable
#define SADC_ENA_PBATEN		(1 << 1)  // PBAT Enable
#define SADC_ENA_SADCINEN	(1 << 0)  // SADCIN Enable

// ADC Configure Register
#define SADC_CFG_EXIN           (1 << 30)
#define SADC_CFG_CLKOUT_NUM_BIT	16
#define SADC_CFG_CLKOUT_NUM_MASK (0x7 << SADC_CFG_CLKOUT_NUM_BIT)
#define SADC_CFG_TS_DMA		(1 << 15)  // Touch Screen DMA Enable
#define SADC_CFG_XYZ_BIT	13  // XYZ selection
#define SADC_CFG_XYZ_MASK	(0x3 << SADC_CFG_XYZ_BIT)
  #define SADC_CFG_XY		(0 << SADC_CFG_XYZ_BIT)
  #define SADC_CFG_XYZ		(1 << SADC_CFG_XYZ_BIT)
  #define SADC_CFG_XYZ1Z2	(2 << SADC_CFG_XYZ_BIT)
#define SADC_CFG_SNUM_BIT	10  // Sample Number
#define SADC_CFG_SNUM_MASK	(0x7 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_1	(0x0 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_2	(0x1 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_3	(0x2 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_4	(0x3 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_5	(0x4 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_6	(0x5 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_8	(0x6 << SADC_CFG_SNUM_BIT)
  #define SADC_CFG_SNUM_9	(0x7 << SADC_CFG_SNUM_BIT)
#define SADC_CFG_CLKDIV_BIT	5  // AD Converter frequency clock divider
#define SADC_CFG_CLKDIV_MASK	(0x1f << SADC_CFG_CLKDIV_BIT)
#define SADC_CFG_PBAT_HIGH	(0 << 4)  // PBAT >= 2.5V
#define SADC_CFG_PBAT_LOW	(1 << 4)  // PBAT < 2.5V
#define SADC_CFG_CMD_BIT	0  // ADC Command
#define SADC_CFG_CMD_MASK	(0xf << SADC_CFG_CMD_BIT)
  #define SADC_CFG_CMD_X_SE	(0x0 << SADC_CFG_CMD_BIT) // X Single-End
  #define SADC_CFG_CMD_Y_SE	(0x1 << SADC_CFG_CMD_BIT) // Y Single-End
  #define SADC_CFG_CMD_X_DIFF	(0x2 << SADC_CFG_CMD_BIT) // X Differential
  #define SADC_CFG_CMD_Y_DIFF	(0x3 << SADC_CFG_CMD_BIT) // Y Differential
  #define SADC_CFG_CMD_Z1_DIFF	(0x4 << SADC_CFG_CMD_BIT) // Z1 Differential
  #define SADC_CFG_CMD_Z2_DIFF	(0x5 << SADC_CFG_CMD_BIT) // Z2 Differential
  #define SADC_CFG_CMD_Z3_DIFF	(0x6 << SADC_CFG_CMD_BIT) // Z3 Differential
  #define SADC_CFG_CMD_Z4_DIFF	(0x7 << SADC_CFG_CMD_BIT) // Z4 Differential
  #define SADC_CFG_CMD_TP_SE	(0x8 << SADC_CFG_CMD_BIT) // Touch Pressure
  #define SADC_CFG_CMD_PBATH_SE	(0x9 << SADC_CFG_CMD_BIT) // PBAT >= 2.5V
  #define SADC_CFG_CMD_PBATL_SE	(0xa << SADC_CFG_CMD_BIT) // PBAT < 2.5V
  #define SADC_CFG_CMD_SADCIN_SE (0xb << SADC_CFG_CMD_BIT) // Measure SADCIN
  #define SADC_CFG_CMD_INT_PEN	(0xc << SADC_CFG_CMD_BIT) // INT_PEN Enable

// ADC Control Register
#define SADC_CTRL_PENDM		(1 << 4)  // Pen Down Interrupt Mask
#define SADC_CTRL_PENUM		(1 << 3)  // Pen Up Interrupt Mask
#define SADC_CTRL_TSRDYM	(1 << 2)  // Touch Screen Data Ready Interrupt Mask
#define SADC_CTRL_PBATRDYM	(1 << 1)  // PBAT Data Ready Interrupt Mask
#define SADC_CTRL_SRDYM		(1 << 0)  // SADCIN Data Ready Interrupt Mask

// ADC Status Register
#define SADC_STATE_TSBUSY	(1 << 7)  // TS A/D is working
#define SADC_STATE_PBATBUSY	(1 << 6)  // PBAT A/D is working
#define SADC_STATE_SBUSY	(1 << 5)  // SADCIN A/D is working
#define SADC_STATE_PEND		(1 << 4)  // Pen Down Interrupt Flag
#define SADC_STATE_PENU		(1 << 3)  // Pen Up Interrupt Flag
#define SADC_STATE_TSRDY	(1 << 2)  // Touch Screen Data Ready Interrupt Flag
#define SADC_STATE_PBATRDY	(1 << 1)  // PBAT Data Ready Interrupt Flag
#define SADC_STATE_SRDY		(1 << 0)  // SADCIN Data Ready Interrupt Flag

// ADC Touch Screen Data Register
#define SADC_TSDAT_DATA0_BIT	0
#define SADC_TSDAT_DATA0_MASK	(0xfff << SADC_TSDAT_DATA0_BIT)
#define SADC_TSDAT_TYPE0	(1 << 15)
#define SADC_TSDAT_DATA1_BIT	16
#define SADC_TSDAT_DATA1_MASK	(0xfff << SADC_TSDAT_DATA1_BIT)
#define SADC_TSDAT_TYPE1	(1 << 31)


//************************************************************************
// SLCD (Smart LCD Controller)
//************************************************************************

#define SLCD_CFG	REG32 (SLCD_BASE + 0xA0)  // SLCD Configure Register
#define SLCD_CTRL	REG8 (SLCD_BASE + 0xA4)  // SLCD Control Register
#define SLCD_STATE	REG8 (SLCD_BASE + 0xA8)  // SLCD Status Register
#define SLCD_DATA	REG32 (SLCD_BASE + 0xAC)  // SLCD Data Register
#define SLCD_FIFO	REG32 (SLCD_BASE + 0xB0)  // SLCD FIFO Register

// SLCD Configure Register
#define SLCD_CFG_BURST_BIT	14
#define SLCD_CFG_BURST_MASK	(0x3 << SLCD_CFG_BURST_BIT)
  #define SLCD_CFG_BURST_4_WORD	(0 << SLCD_CFG_BURST_BIT)
  #define SLCD_CFG_BURST_8_WORD	(1 << SLCD_CFG_BURST_BIT)
#define SLCD_CFG_DWIDTH_BIT	10
#define SLCD_CFG_DWIDTH_MASK	(0x7 << SLCD_CFG_DWIDTH_BIT)
  #define SLCD_CFG_DWIDTH_18	(0 << SLCD_CFG_DWIDTH_BIT)
  #define SLCD_CFG_DWIDTH_16	(1 << SLCD_CFG_DWIDTH_BIT)
  #define SLCD_CFG_DWIDTH_8_x3	(2 << SLCD_CFG_DWIDTH_BIT)
  #define SLCD_CFG_DWIDTH_8_x2	(3 << SLCD_CFG_DWIDTH_BIT)
  #define SLCD_CFG_DWIDTH_9_x2	(4 << SLCD_CFG_DWIDTH_BIT)
#define SLCD_CFG_CWIDTH_16BIT	(0 << 8)
#define SLCD_CFG_CWIDTH_8BIT	(1 << 8)
#define SLCD_CFG_CS_ACTIVE_LOW	(0 << 4)
#define SLCD_CFG_CS_ACTIVE_HIGH	(1 << 4)
#define SLCD_CFG_RS_CMD_LOW	(0 << 3)
#define SLCD_CFG_RS_CMD_HIGH	(1 << 3)
#define SLCD_CFG_CLK_ACTIVE_FALLING	(0 << 1)
#define SLCD_CFG_CLK_ACTIVE_RISING	(1 << 1)
#define SLCD_CFG_TYPE_PARALLEL	(0 << 0)
#define SLCD_CFG_TYPE_SERIAL	(1 << 0)

// SLCD Control Register
#define SLCD_CTRL_DMA_EN	(1 << 0)

// SLCD Status Register
#define SLCD_STATE_BUSY		(1 << 0)

// SLCD Data Register
#define SLCD_DATA_RS_DATA	(0 << 31)
#define SLCD_DATA_RS_COMMAND	(1 << 31)

// SLCD FIFO Register
#define SLCD_FIFO_RS_DATA	(0 << 31)
#define SLCD_FIFO_RS_COMMAND	(1 << 31)


//************************************************************************
// LCD (LCD Controller)
//************************************************************************
#define LCD_CFG		REG32 (LCD_BASE + 0x00) // LCD Configure Register
#define LCD_VSYNC	REG32 (LCD_BASE + 0x04) // Vertical Synchronize Register
#define LCD_HSYNC	REG32 (LCD_BASE + 0x08) // Horizontal Synchronize Register
#define LCD_VAT		REG32 (LCD_BASE + 0x0c) // Virtual Area Setting Register
#define LCD_DAH		REG32 (LCD_BASE + 0x10) // Display Area Horizontal Start/End Point
#define LCD_DAV		REG32 (LCD_BASE + 0x14) // Display Area Vertical Start/End Point
#define LCD_PS		REG32 (LCD_BASE + 0x18) // PS Signal Setting
#define LCD_CLS		REG32 (LCD_BASE + 0x1c) // CLS Signal Setting
#define LCD_SPL		REG32 (LCD_BASE + 0x20) // SPL Signal Setting
#define LCD_REV		REG32 (LCD_BASE + 0x24) // REV Signal Setting
#define LCD_CTRL	REG32 (LCD_BASE + 0x30) // LCD Control Register
#define LCD_STATE	REG32 (LCD_BASE + 0x34) // LCD Status Register
#define LCD_IID		REG32 (LCD_BASE + 0x38) // Interrupt ID Register
#define LCD_DA0		REG32 (LCD_BASE + 0x40) // Descriptor Address Register 0
#define LCD_SA0		REG32 (LCD_BASE + 0x44) // Source Address Register 0
#define LCD_FID0	REG32 (LCD_BASE + 0x48) // Frame ID Register 0
#define LCD_CMD0	REG32 (LCD_BASE + 0x4c) // DMA Command Register 0
#define LCD_DA1		REG32 (LCD_BASE + 0x50) // Descriptor Address Register 1
#define LCD_SA1		REG32 (LCD_BASE + 0x54) // Source Address Register 1
#define LCD_FID1	REG32 (LCD_BASE + 0x58) // Frame ID Register 1
#define LCD_CMD1	REG32 (LCD_BASE + 0x5c) // DMA Command Register 1

// LCD Configure Register
#define LCD_CFG_LCDPIN_BIT	31  // LCD pins selection
#define LCD_CFG_LCDPIN_MASK	(0x1 << LCD_CFG_LCDPIN_BIT)
  #define LCD_CFG_LCDPIN_LCD	(0x0 << LCD_CFG_LCDPIN_BIT)
  #define LCD_CFG_LCDPIN_SLCD	(0x1 << LCD_CFG_LCDPIN_BIT)
#define LCD_CFG_PSM		(1 << 23) // PS signal mode
#define LCD_CFG_CLSM		(1 << 22) // CLS signal mode
#define LCD_CFG_SPLM		(1 << 21) // SPL signal mode
#define LCD_CFG_REVM		(1 << 20) // REV signal mode
#define LCD_CFG_HSYNM		(1 << 19) // HSYNC signal mode
#define LCD_CFG_PCLKM		(1 << 18) // PCLK signal mode
#define LCD_CFG_INVDAT		(1 << 17) // Inverse output data
#define LCD_CFG_SYNDIR_IN	(1 << 16) // VSYNC&HSYNC direction
#define LCD_CFG_PSP		(1 << 15) // PS pin reset state
#define LCD_CFG_CLSP		(1 << 14) // CLS pin reset state
#define LCD_CFG_SPLP		(1 << 13) // SPL pin reset state
#define LCD_CFG_REVP		(1 << 12) // REV pin reset state
#define LCD_CFG_HSP		(1 << 11) // HSYNC pority:0-active high,1-active low
#define LCD_CFG_PCP		(1 << 10) // PCLK pority:0-rising,1-falling
#define LCD_CFG_DEP		(1 << 9)  // DE pority:0-active high,1-active low
#define LCD_CFG_VSP		(1 << 8)  // VSYNC pority:0-rising,1-falling
#define LCD_CFG_PDW_BIT		4  // STN pins utilization
#define LCD_CFG_PDW_MASK	(0x3 << LCD_DEV_PDW_BIT)
#define LCD_CFG_PDW_1		(0 << LCD_CFG_PDW_BIT) // LCD_D[0]
  #define LCD_CFG_PDW_2		(1 << LCD_CFG_PDW_BIT) // LCD_D[0:1]
  #define LCD_CFG_PDW_4		(2 << LCD_CFG_PDW_BIT) // LCD_D[0:3]/LCD_D[8:11]
  #define LCD_CFG_PDW_8		(3 << LCD_CFG_PDW_BIT) // LCD_D[0:7]/LCD_D[8:15]
#define LCD_CFG_MODE_BIT	0  // Display Device Mode Select
#define LCD_CFG_MODE_MASK	(0x0f << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_GENERIC_TFT	(0 << LCD_CFG_MODE_BIT) // 16,18 bit TFT
  #define LCD_CFG_MODE_SPECIAL_TFT_1	(1 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_SPECIAL_TFT_2	(2 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_SPECIAL_TFT_3	(3 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_NONINTER_CCIR656	(4 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_INTER_CCIR656	(5 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_SINGLE_CSTN	(8 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_SINGLE_MSTN	(9 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_DUAL_CSTN	(10 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_DUAL_MSTN	(11 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_SERIAL_TFT	(12 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_GENERIC_18BIT_TFT  (13 << LCD_CFG_MODE_BIT)
  // JZ47XX defines
  #define LCD_CFG_MODE_SHARP_HR		(1 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_CASIO_TFT	(2 << LCD_CFG_MODE_BIT)
  #define LCD_CFG_MODE_SAMSUNG_ALPHA	(3 << LCD_CFG_MODE_BIT)



// Vertical Synchronize Register
#define LCD_VSYNC_VPS_BIT	16  // VSYNC pulse start in line clock, fixed to 0
#define LCD_VSYNC_VPS_MASK	(0xffff << LCD_VSYNC_VPS_BIT)
#define LCD_VSYNC_VPE_BIT	0   // VSYNC pulse end in line clock
#define LCD_VSYNC_VPE_MASK	(0xffff << LCD_VSYNC_VPS_BIT)

// Horizontal Synchronize Register
#define LCD_HSYNC_HPS_BIT	16  // HSYNC pulse start position in dot clock
#define LCD_HSYNC_HPS_MASK	(0xffff << LCD_HSYNC_HPS_BIT)
#define LCD_HSYNC_HPE_BIT	0   // HSYNC pulse end position in dot clock
#define LCD_HSYNC_HPE_MASK	(0xffff << LCD_HSYNC_HPE_BIT)

// Virtual Area Setting Register
#define LCD_VAT_HT_BIT		16  // Horizontal Total size in dot clock
#define LCD_VAT_HT_MASK		(0xffff << LCD_VAT_HT_BIT)
#define LCD_VAT_VT_BIT		0   // Vertical Total size in dot clock
#define LCD_VAT_VT_MASK		(0xffff << LCD_VAT_VT_BIT)

// Display Area Horizontal Start/End Point Register
#define LCD_DAH_HDS_BIT		16  // Horizontal display area start in dot clock
#define LCD_DAH_HDS_MASK	(0xffff << LCD_DAH_HDS_BIT)
#define LCD_DAH_HDE_BIT		0   // Horizontal display area end in dot clock
#define LCD_DAH_HDE_MASK	(0xffff << LCD_DAH_HDE_BIT)

// Display Area Vertical Start/End Point Register
#define LCD_DAV_VDS_BIT		16  // Vertical display area start in line clock
#define LCD_DAV_VDS_MASK	(0xffff << LCD_DAV_VDS_BIT)
#define LCD_DAV_VDE_BIT		0   // Vertical display area end in line clock
#define LCD_DAV_VDE_MASK	(0xffff << LCD_DAV_VDE_BIT)

// PS Signal Setting
#define LCD_PS_PSS_BIT		16  // PS signal start position in dot clock
#define LCD_PS_PSS_MASK		(0xffff << LCD_PS_PSS_BIT)
#define LCD_PS_PSE_BIT		0   // PS signal end position in dot clock
#define LCD_PS_PSE_MASK		(0xffff << LCD_PS_PSE_BIT)

// CLS Signal Setting
#define LCD_CLS_CLSS_BIT	16  // CLS signal start position in dot clock
#define LCD_CLS_CLSS_MASK	(0xffff << LCD_CLS_CLSS_BIT)
#define LCD_CLS_CLSE_BIT	0   // CLS signal end position in dot clock
#define LCD_CLS_CLSE_MASK	(0xffff << LCD_CLS_CLSE_BIT)

// SPL Signal Setting
#define LCD_SPL_SPLS_BIT	16  // SPL signal start position in dot clock
#define LCD_SPL_SPLS_MASK	(0xffff << LCD_SPL_SPLS_BIT)
#define LCD_SPL_SPLE_BIT	0   // SPL signal end position in dot clock
#define LCD_SPL_SPLE_MASK	(0xffff << LCD_SPL_SPLE_BIT)

// REV Signal Setting
#define LCD_REV_REVS_BIT	16  // REV signal start position in dot clock
#define LCD_REV_REVS_MASK	(0xffff << LCD_REV_REVS_BIT)

// LCD Control Register
#define LCD_CTRL_BST_BIT	28  // Burst Length Selection
#define LCD_CTRL_BST_MASK	(0x03 << LCD_CTRL_BST_BIT)
  #define LCD_CTRL_BST_4	(0 << LCD_CTRL_BST_BIT) // 4-word
  #define LCD_CTRL_BST_8	(1 << LCD_CTRL_BST_BIT) // 8-word
  #define LCD_CTRL_BST_16	(2 << LCD_CTRL_BST_BIT) // 16-word
#define LCD_CTRL_RGB565		(0 << 27) // RGB565 mode
#define LCD_CTRL_RGB555		(1 << 27) // RGB555 mode
#define LCD_CTRL_OFUP		(1 << 26) // Output FIFO underrun protection enable
#define LCD_CTRL_FRC_BIT	24  // STN FRC Algorithm Selection
#define LCD_CTRL_FRC_MASK	(0x03 << LCD_CTRL_FRC_BIT)
  #define LCD_CTRL_FRC_16	(0 << LCD_CTRL_FRC_BIT) // 16 grayscale
  #define LCD_CTRL_FRC_4	(1 << LCD_CTRL_FRC_BIT) // 4 grayscale
  #define LCD_CTRL_FRC_2	(2 << LCD_CTRL_FRC_BIT) // 2 grayscale
#define LCD_CTRL_PDD_BIT	16  // Load Palette Delay Counter
#define LCD_CTRL_PDD_MASK	(0xff << LCD_CTRL_PDD_BIT)
#define LCD_CTRL_EOFM		(1 << 13) // EOF interrupt mask
#define LCD_CTRL_SOFM		(1 << 12) // SOF interrupt mask
#define LCD_CTRL_OFUM		(1 << 11) // Output FIFO underrun interrupt mask
#define LCD_CTRL_IFUM0		(1 << 10) // Input FIFO 0 underrun interrupt mask
#define LCD_CTRL_IFUM1		(1 << 9)  // Input FIFO 1 underrun interrupt mask
#define LCD_CTRL_LDDM		(1 << 8)  // LCD disable done interrupt mask
#define LCD_CTRL_QDM		(1 << 7)  // LCD quick disable done interrupt mask
#define LCD_CTRL_BEDN		(1 << 6)  // Endian selection
#define LCD_CTRL_PEDN		(1 << 5)  // Endian in byte:0-msb first, 1-lsb first
#define LCD_CTRL_DIS		(1 << 4)  // Disable indicate bit
#define LCD_CTRL_ENA		(1 << 3)  // LCD enable bit
#define LCD_CTRL_BPP_BIT	0  // Bits Per Pixel
#define LCD_CTRL_BPP_MASK	(0x07 << LCD_CTRL_BPP_BIT)
  #define LCD_CTRL_BPP_1	(0 << LCD_CTRL_BPP_BIT) // 1 bpp
  #define LCD_CTRL_BPP_2	(1 << LCD_CTRL_BPP_BIT) // 2 bpp
  #define LCD_CTRL_BPP_4	(2 << LCD_CTRL_BPP_BIT) // 4 bpp
  #define LCD_CTRL_BPP_8	(3 << LCD_CTRL_BPP_BIT) // 8 bpp
  #define LCD_CTRL_BPP_16	(4 << LCD_CTRL_BPP_BIT) // 15/16 bpp
  #define LCD_CTRL_BPP_18_24	(5 << LCD_CTRL_BPP_BIT) // 18/24/32 bpp

// LCD Status Register
#define LCD_STATE_QD		(1 << 7) // Quick Disable Done
#define LCD_STATE_EOF		(1 << 5) // EOF Flag
#define LCD_STATE_SOF		(1 << 4) // SOF Flag
#define LCD_STATE_OFU		(1 << 3) // Output FIFO Underrun
#define LCD_STATE_IFU0		(1 << 2) // Input FIFO 0 Underrun
#define LCD_STATE_IFU1		(1 << 1) // Input FIFO 1 Underrun
#define LCD_STATE_LDD		(1 << 0) // LCD Disabled

// DMA Command Register
#define LCD_CMD_SOFINT		(1 << 31)
#define LCD_CMD_EOFINT		(1 << 30)
#define LCD_CMD_PAL		(1 << 28)
#define LCD_CMD_LEN_BIT		0
#define LCD_CMD_LEN_MASK	(0xffffff << LCD_CMD_LEN_BIT)


//************************************************************************
// USB Device
//************************************************************************
#define UDC_FADDR		REG8 (UDC_BASE + 0x00) // Function Address 8-bit
#define UDC_POWER		REG8 (UDC_BASE + 0x01) // Power Managemetn 8-bit
#define UDC_INTRIN		REG16 (UDC_BASE + 0x02) // Interrupt IN 16-bit
#define UDC_INTROUT		REG16 (UDC_BASE + 0x04) // Interrupt OUT 16-bit
#define UDC_INTRINE		REG16 (UDC_BASE + 0x06) // Intr IN enable 16-bit
#define UDC_INTROUTE		REG16 (UDC_BASE + 0x08) // Intr OUT enable 16-bit
#define UDC_INTRUSB		REG8 (UDC_BASE + 0x0a) // Interrupt USB 8-bit
#define UDC_INTRUSBE		REG8 (UDC_BASE + 0x0b) // Interrupt USB Enable 8-bit
#define UDC_FRAME		REG16 (UDC_BASE + 0x0c) // Frame number 16-bit
#define UDC_INDEX		REG8 (UDC_BASE + 0x0e) // Index register 8-bit
#define UDC_TESTMODE		REG8 (UDC_BASE + 0x0f) // USB test mode 8-bit

#define UDC_CSR0		REG8 (UDC_BASE + 0x12) // EP0 CSR 8-bit
#define UDC_INMAXP		REG16 (UDC_BASE + 0x10) // EP1-2 IN Max Pkt Size 16-bit
#define UDC_INCSR		REG16 (UDC_BASE + 0x12) // EP1-2 IN CSR LSB 8/16bit
#define UDC_INCSRH		REG8 (UDC_BASE + 0x13) // EP1-2 IN CSR MSB 8-bit
#define UDC_OUTMAXP		REG16 (UDC_BASE + 0x14) // EP1 OUT Max Pkt Size 16-bit
#define UDC_OUTCSR		REG16 (UDC_BASE + 0x16) // EP1 OUT CSR LSB 8/16bit
#define UDC_OUTCSRH		REG8 (UDC_BASE + 0x17) // EP1 OUT CSR MSB 8-bit
#define UDC_OUTCOUNT		REG16 (UDC_BASE + 0x18) // bytes in EP0/1 OUT FIFO 16-bit

#define UDC_FIFO(ep)		REG32 (UDC_BASE + 0x20 + 4 * (ep))
#define UDC_FIFO8(ep)		REG8 (UDC_BASE + 0x20 + 4 * (ep))

#define UDC_EPINFO		REG32 (UDC_BASE + 0x78) // Endpoint information
#define UDC_RAMINFO		REG32 (UDC_BASE + 0x79) // RAM information

#define UDC_INTR		REG32 (UDC_BASE + 0x200) // DMA pending interrupts
#define UDC_CNTL1		REG32 (UDC_BASE + 0x204) // DMA channel 1 control
#define UDC_ADDR1		REG32 (UDC_BASE + 0x208) // DMA channel 1 AHB memory addr
#define UDC_COUNT1		REG32 (UDC_BASE + 0x20c) // DMA channel 1 byte count
#define UDC_CNTL2		REG32 (UDC_BASE + 0x214) // DMA channel 2 control
#define UDC_ADDR2		REG32 (UDC_BASE + 0x218) // DMA channel 2 AHB memory addr
#define UDC_COUNT2		REG32 (UDC_BASE + 0x21c) // DMA channel 2 byte count


// Power register bit masks
#define UDC_POWER_SUSPENDM	0x01
#define UDC_POWER_RESUME	0x04
#define UDC_POWER_HSMODE	0x10
#define UDC_POWER_HSENAB	0x20
#define UDC_POWER_SOFTCONN	0x40

// Interrupt register bit masks
#define UDC_INTR_SUSPEND	0x01
#define UDC_INTR_RESUME		0x02
#define UDC_INTR_RESET		0x04

#define UDC_INTR_EP0		0x0001
#define UDC_INTR_INEP1		0x0002
#define UDC_INTR_INEP2		0x0004
#define UDC_INTR_OUTEP1		0x0002

// CSR0 bit masks
#define UDC_CSR0_OUTPKTRDY	0x01
#define UDC_CSR0_INPKTRDY	0x02
#define UDC_CSR0_SENTSTALL	0x04
#define UDC_CSR0_DATAEND	0x08
#define UDC_CSR0_SETUPEND	0x10
#define UDC_CSR0_SENDSTALL	0x20
#define UDC_CSR0_SVDOUTPKTRDY	0x40
#define UDC_CSR0_SVDSETUPEND	0x80

// Endpoint CSR register bits
#define UDC_INCSRH_AUTOSET	0x80
#define UDC_INCSRH_ISO		0x40
#define UDC_INCSRH_MODE		0x20
#define UDC_INCSRH_DMAREQENAB	0x10
#define UDC_INCSRH_DMAREQMODE	0x04
#define UDC_INCSR_CDT		0x40
#define UDC_INCSR_SENTSTALL	0x20
#define UDC_INCSR_SENDSTALL	0x10
#define UDC_INCSR_FF		0x08
#define UDC_INCSR_UNDERRUN	0x04
#define UDC_INCSR_FFNOTEMPT	0x02
#define UDC_INCSR_INPKTRDY	0x01
#define UDC_OUTCSRH_AUTOCLR	0x80
#define UDC_OUTCSRH_ISO		0x40
#define UDC_OUTCSRH_DMAREQENAB	0x20
#define UDC_OUTCSRH_DNYT	0x10
#define UDC_OUTCSRH_DMAREQMODE	0x08
#define UDC_OUTCSR_CDT		0x80
#define UDC_OUTCSR_SENTSTALL	0x40
#define UDC_OUTCSR_SENDSTALL	0x20
#define UDC_OUTCSR_FF		0x10
#define UDC_OUTCSR_DATAERR	0x08
#define UDC_OUTCSR_OVERRUN	0x04
#define UDC_OUTCSR_FFFULL	0x02
#define UDC_OUTCSR_OUTPKTRDY	0x01

// Testmode register bits
#define UDC_TEST_SE0NAK		0x01
#define UDC_TEST_J		0x02
#define UDC_TEST_K		0x04
#define UDC_TEST_PACKET		0x08

// DMA control bits
#define UDC_CNTL_ENA		0x01
#define UDC_CNTL_DIR_IN		0x02
#define UDC_CNTL_MODE_1		0x04
#define UDC_CNTL_INTR_EN	0x08
#define UDC_CNTL_EP(n)		((n) << 4)
#define UDC_CNTL_BURST_0	(0 << 9)
#define UDC_CNTL_BURST_4	(1 << 9)
#define UDC_CNTL_BURST_8	(2 << 9)
#define UDC_CNTL_BURST_16	(3 << 9)

//##########################################################################
//**************************************************************************
// GPIO
//**************************************************************************

//------------------------------------------------------
// GPIO Pins Description
//
// PORT 0
//
// PIN/BIT N		FUNC0		FUNC1
//	0		D0		-
//	1		D1		-
//	2		D2		-
//	3		D3		-
//	4		D4		-
//	5		D5		-
//	6		D6		-
//	7		D7		-
//	8		D8		-
//	9		D9		-
//	10		D10		-
//	11		D11		-
//	12		D12		-
//	13		D13		-
//	14		D14		-
//	15		D15		-
//	16		D16		-
//	17		D17		-
//	18		D18		-
//	19		D19		-
//	20		D20		-
//	21		D21		-
//	22		D22		-
//	23		D23		-
//	24		D24		-
//	25		D25		-
//	26		D26		-
//	27		D27		-
//	28		D28		-
//	29		D29		-
//	30		D30		-
//	31		D31		-
//
//------------------------------------------------------
// PORT 1
//
// PIN/BIT N		FUNC0		FUNC1
//	0		A0		-
//	1		A1		-
//	2		A2		-
//	3		A3		-
//	4		A4		-
//	5		A5		-
//	6		A6		-
//	7		A7		-
//	8		A8		-
//	9		A9		-
//	10		A10		-
//	11		A11		-
//	12		A12		-
//	13		A13		-
//	14		A14		-
//	15		A15/CL		-
//	16		A16/AL		-
//	17		LCD_CLS		A21
//	18		LCD_SPL		A22
//	19		DCS#		-
//	20		RAS#		-
//	21		CAS#		-
//	22		RDWE#/BUFD#	-
//	23		CKE		-
//	24		CKO		-
//	25		CS1#		-
//	26		CS2#		-
//	27		CS3#		-
//	28		CS4#		-
//	29		RD#		-
//	30		WR#		-
//	31		WE0#		-
//
// Note: PIN15&16 are CL&AL when connecting to NAND flash.
//------------------------------------------------------
// PORT 2
//
// PIN/BIT N		FUNC0		FUNC1
//	0		LCD_D0		-
//	1		LCD_D1		-
//	2		LCD_D2		-
//	3		LCD_D3		-
//	4		LCD_D4		-
//	5		LCD_D5		-
//	6		LCD_D6		-
//	7		LCD_D7		-
//	8		LCD_D8		-
//	9		LCD_D9		-
//	10		LCD_D10		-
//	11		LCD_D11		-
//	12		LCD_D12		-
//	13		LCD_D13		-
//	14		LCD_D14		-
//	15		LCD_D15		-
//	16		LCD_D16		-
//	17		LCD_D17		-
//	18		LCD_PCLK	-
//	19		LCD_HSYNC	-
//	20		LCD_VSYNC	-
//	21		LCD_DE		-
//	22		LCD_PS		A19
//	23		LCD_REV		A20
//	24		WE1#		-
//	25		WE2#		-
//	26		WE3#		-
//	27		WAIT#		-
//	28		FRE#		-
//	29		FWE#		-
//	30(NOTE:FRB#)	-		-
//	31		-		-
//
// NOTE(1): PIN30 is used for FRB# when connecting to NAND flash.
//------------------------------------------------------
// PORT 3
//
// PIN/BIT N		FUNC0		FUNC1
//	0		CIM_D0		-
//	1		CIM_D1		-
//	2		CIM_D2		-
//	3		CIM_D3		-
//	4		CIM_D4		-
//	5		CIM_D5		-
//	6		CIM_D6		-
//	7		CIM_D7		-
//	8		MSC_CMD		-
//	9		MSC_CLK		-
//	10		MSC_D0		-
//	11		MSC_D1		-
//	12		MSC_D2		-
//	13		MSC_D3		-
//	14		CIM_MCLK	-
//	15		CIM_PCLK	-
//	16		CIM_VSYNC	-
//	17		CIM_HSYNC	-
//	18		SSI_CLK		SCLK_RSTN
//	19		SSI_CE0#	BIT_CLK(AIC)
//	20		SSI_DT		SDATA_OUT(AIC)
//	21		SSI_DR		SDATA_IN(AIC)
//	22		SSI_CE1#&GPC	SYNC(AIC)
//	23		PWM0		I2C_SDA
//	24		PWM1		I2C_SCK
//	25		PWM2		UART0_TxD
//	26		PWM3		UART0_RxD
//	27		PWM4		A17
//	28		PWM5		A18
//	29		-		-
//	30		PWM6		UART0_CTS/UART1_RxD
//	31		PWM7		UART0_RTS/UART1_TxD
//
//////////////////////////////////////////////////////////

// p is the port number (0,1,2,3)
// o is the pin offset (0-31) inside the port

//-------------------------------------------
// Function Pins Mode

static void gpio_as_func0 (unsigned p, unsigned o):
	GPIO_PXFUNS (p) = (1 << o)
	GPIO_PXSELC (p) = (1 << o)

static void gpio_as_func1 (unsigned p, unsigned o):
	GPIO_PXFUNS (p) = (1 << o)
	GPIO_PXSELS (p) = (1 << o)

// D0 ~ D31, A0 ~ A16, DCS#, RAS#, CAS#, CKE#, RDWE#, CKO#, WE0#, WE1#, WE2#, WE3#
static void gpio_as_sdram_32bit ():
	GPIO_PXFUNS (0) = 0xffffffff
	GPIO_PXSELC (0) = 0xffffffff
	GPIO_PXPES (0) = 0xffffffff
	GPIO_PXFUNS (1) = 0x81f9ffff
	GPIO_PXSELC (1) = 0x81f9ffff
	GPIO_PXPES (1) = 0x81f9ffff
	GPIO_PXFUNS (2) = 0x07000000
	GPIO_PXSELC (2) = 0x07000000
	GPIO_PXPES (2) = 0x07000000

// D0 ~ D15, A0 ~ A16, DCS#, RAS#, CAS#, CKE#, RDWE#, CKO#, WE0#, WE1#
static void gpio_as_sdram_16bit():
	GPIO_PXFUNS (0) = 0x5442bfaa
	GPIO_PXSELC (0) = 0x5442bfaa
	GPIO_PXPES (0) = 0x5442bfaa
	GPIO_PXFUNS (1) = 0x81f9ffff
	GPIO_PXSELC (1) = 0x81f9ffff
	GPIO_PXPES (1) = 0x81f9ffff
	GPIO_PXFUNS (2) = 0x01000000
	GPIO_PXSELC (2) = 0x01000000
	GPIO_PXPES (2) = 0x01000000

// CS1#, CLE, ALE, FRE#, FWE#, FRB#, RDWE#/BUFD#
static void gpio_as_nand ():
	GPIO_PXFUNS (1) = 0x02018000
	GPIO_PXSELC (1) = 0x02018000
	GPIO_PXPES (1) = 0x02018000
	GPIO_PXFUNS (2) = 0x30000000
	GPIO_PXSELC (2) = 0x30000000
	GPIO_PXPES (2) = 0x30000000
	GPIO_PXFUNC (2) = 0x40000000
	GPIO_PXSELC (2) = 0x40000000
	GPIO_PXDIRC (2) = 0x40000000
	GPIO_PXPES (2) = 0x40000000
	GPIO_PXFUNS (1) = 0x00400000
	GPIO_PXSELC (1) = 0x00400000

// UART0_TxD, UART_RxD0
static void gpio_as_uart0 ():
	GPIO_PXFUNS (3) = 0x06000000
	GPIO_PXSELS (3) = 0x06000000
	GPIO_PXPES (3) = 0x06000000

// UART0_CTS, UART0_RTS
static void gpio_as_ctsrts ():
	GPIO_PXFUNS (3) = 0xc0000000
	GPIO_PXSELS (3) = 0xc0000000
	GPIO_PXTRGC (3) = 0xc0000000
	GPIO_PXPES (3) = 0xc0000000

// UART1_TxD, UART1_RxD1
static void gpio_as_uart1():
	GPIO_PXFUNS (3) = 0xc0000000
	GPIO_PXSELC (3) = 0xc0000000
	GPIO_PXTRGS (3) = 0xc0000000
	GPIO_PXPES (3) = 0xc0000000

// LCD_D0~LCD_D15, LCD_PCLK, LCD_HSYNC, LCD_VSYNC, LCD_DE
static void gpio_as_lcd_16bit ():
	GPIO_PXFUNS (2) = 0x003cffff
	GPIO_PXSELC (2) = 0x003cffff
	GPIO_PXPES (2) = 0x003cffff

// LCD_D0~LCD_D17, LCD_PCLK, LCD_HSYNC, LCD_VSYNC, LCD_DE
static void gpio_as_lcd_18bit ():
	GPIO_PXFUNS (2) = 0x003fffff
	GPIO_PXSELC (2) = 0x003fffff
	GPIO_PXPES (2) = 0x003fffff

// LCD_PS, LCD_REV, LCD_CLS, LCD_SPL
static void gpio_as_lcd_spl ():
	GPIO_PXFUNS (1) = 0x00060000
	GPIO_PXSELC (1) = 0x00060000
	GPIO_PXPES (1)  = 0x00060000
	GPIO_PXFUNS (2) = 0x00c00000
	GPIO_PXSELC (2) = 0x00c00000
	GPIO_PXPES (2)  = 0x00c00000

// CIM_D0~CIM_D7, CIM_MCLK, CIM_PCLK, CIM_VSYNC, CIM_HSYNC
static void gpio_as_cim ():
	GPIO_PXFUNS (3) = 0x0003c0ff
	GPIO_PXSELC (3) = 0x0003c0ff
	GPIO_PXPES (3) = 0x0003c0ff

// SDATA_OUT, SDATA_IN, BIT_CLK, SYNC, SCLK_RESET
static void gpio_as_aic ():
	GPIO_PXFUNS(3) = 0x007c0000
	GPIO_PXSELS(3) = 0x007c0000
	GPIO_PXPES(3) = 0x007c0000

// MSC_CMD, MSC_CLK, MSC_D0 ~ MSC_D3
static void gpio_as_msc ():
	GPIO_PXFUNS (3) = 0x00003f00
	GPIO_PXSELC (3) = 0x00003f00
	GPIO_PXPES (3) = 0x00003f00

// SSI_CS0, SSI_CLK, SSI_DT, SSI_DR
static void gpio_as_ssi ():
	GPIO_PXFUNS (3) = 0x003c0000
	GPIO_PXSELC (3) = 0x003c0000
	GPIO_PXPES (3) = 0x003c0000

// I2C_SCK, I2C_SDA
static void gpio_as_i2c ():
	GPIO_PXFUNS (3) = 0x01800000
	GPIO_PXSELS (3) = 0x01800000
	GPIO_PXPES (3) = 0x01800000

// PWM*
static void gpio_as_pwm0 ():
	GPIO_PXFUNS (3) = 0x00800000
	GPIO_PXSELC (3) = 0x00800000
	GPIO_PXPES (3) = 0x00800000
static void gpio_as_pwm1 ():
	GPIO_PXFUNS (3) = 0x01000000
	GPIO_PXSELC (3) = 0x01000000
	GPIO_PXPES (3) = 0x01000000
static void gpio_as_pwm2 ():
	GPIO_PXFUNS (3) = 0x02000000
	GPIO_PXSELC (3) = 0x02000000
	GPIO_PXPES (3) = 0x02000000
static void gpio_as_pwm3 ():
	GPIO_PXFUNS (3) = 0x04000000
	GPIO_PXSELC (3) = 0x04000000
	GPIO_PXPES (3) = 0x04000000
static void gpio_as_pwm4 ():
	GPIO_PXFUNS (3) = 0x08000000
	GPIO_PXSELC (3) = 0x08000000
	GPIO_PXPES (3) = 0x08000000
static void gpio_as_pwm5 ():
	GPIO_PXFUNS (3) = 0x10000000
	GPIO_PXSELC (3) = 0x10000000
	GPIO_PXPES (3) = 0x10000000
static void gpio_as_pwm6 ():
	GPIO_PXFUNS (3) = 0x40000000
	GPIO_PXSELC (3) = 0x40000000
	GPIO_PXPES (3) = 0x40000000
static void gpio_as_pwm7 ():
	GPIO_PXFUNS (3) = 0x80000000
	GPIO_PXSELC (3) = 0x80000000
	GPIO_PXPES (3) = 0x80000000

// n = 0 ~ 7
#define gpio_as_pwm(n)	(gpio_as_pwm##n ())

//-------------------------------------------
// GPIO or Interrupt Mode

static unsigned gpio_get_port (unsigned p):
	return GPIO_PXPIN (p)
static unsigned gpio_get_irqs (unsigned p):
	return GPIO_PXFLG (p)

static void gpio_as_gpio (unsigned p, unsigned pins):
	GPIO_PXFUNC (p) = pins
static void gpio_as_output (unsigned p, unsigned pins):
	GPIO_PXDIRS (p) = pins
static void gpio_as_input (unsigned p, unsigned pins):
	GPIO_PXDIRC (p) = pins
// Set gpio as interrupt.  It must already be set as gpio.  It must be unmasked before it will trigger.
static void gpio_as_interrupt (unsigned p, unsigned pins, bool high, bool level):
	GPIO_PXIMS (p) = pins
	if level:
		GPIO_PXTRGC (p) = pins
	else:
		GPIO_PXTRGS (p) = pins
	GPIO_PXSELS (p) = pins
	if high:
		GPIO_PXDIRS (p) = pins
	else:
		GPIO_PXDIRC (p) = pins
	GPIO_PXFLGC (p) = pins

static void gpio_set (unsigned p, unsigned pins):
	GPIO_PXDATS (p) = pins
static void gpio_clear (unsigned p, unsigned pins):
	GPIO_PXDATC (p) = pins
static void gpio_mask_irq (unsigned p, unsigned pins):
	GPIO_PXIMS (p) = pins
static void gpio_unmask_irq (unsigned p, unsigned pins):
	GPIO_PXIMC (p) = pins
static void gpio_ack_irq (unsigned p, unsigned pins):
	GPIO_PXFLGC (p) = pins

static void gpio_enable_pull (unsigned p, unsigned pins):
	GPIO_PXPEC (p) = pins
static void gpio_disable_pull (unsigned p, unsigned pins):
	GPIO_PXPES (p) = pins


//**************************************************************************
// CPM
//**************************************************************************
static void pll_init ():
	// The cpu clock frequency
	//unsigned const cpu_clock = 336000000
	//unsigned const pixclock = 25846153
	unsigned const cpu_clock = 200000000
	unsigned const pixclock = 13500000
	// Configure the pll frequency to cpu_clock.
	CPM_CPPCR = ((cpu_clock * 2 / JZ_EXTAL - 2) << CPM_CPPCR_PLLM_BIT) | (0 << CPM_CPPCR_PLLN_BIT) | (0 << CPM_CPPCR_PLLOD_BIT) | (0x20 << CPM_CPPCR_PLLST_BIT) | CPM_CPPCR_PLLEN
	// Set up dividers; see documentation for the meaning of all the values.
	// USB clock seems to work when bypassing the pll. (even though it must be 48 MHz according to the datasheet.)
	CPM_CPCCR = CPM_CPCCR_CLKOEN | (0 << CPM_CPCCR_CDIV_BIT) | (2 << CPM_CPCCR_HDIV_BIT) | (2 << CPM_CPCCR_PDIV_BIT) | (2 << CPM_CPCCR_MDIV_BIT) | (3 << CPM_CPCCR_LDIV_BIT) | CPM_CPCCR_CE | CPM_CPCCR_PCS
	CPM_LPCDR = (cpu_clock / pixclock) - 1

static unsigned cpm_get_pllm ():
	return (CPM_CPPCR & CPM_CPPCR_PLLM_MASK) >> CPM_CPPCR_PLLM_BIT
static unsigned cpm_get_plln ():
	return (CPM_CPPCR & CPM_CPPCR_PLLN_MASK) >> CPM_CPPCR_PLLN_BIT
static unsigned cpm_get_pllod ():
	return (CPM_CPPCR & CPM_CPPCR_PLLOD_MASK) >> CPM_CPPCR_PLLOD_BIT

static unsigned cpm_get_cdiv ():
	return (CPM_CPCCR & CPM_CPCCR_CDIV_MASK) >> CPM_CPCCR_CDIV_BIT
static unsigned cpm_get_hdiv ():
	return (CPM_CPCCR & CPM_CPCCR_HDIV_MASK) >> CPM_CPCCR_HDIV_BIT
static unsigned cpm_get_pdiv ():
	return (CPM_CPCCR & CPM_CPCCR_PDIV_MASK) >> CPM_CPCCR_PDIV_BIT
static unsigned cpm_get_mdiv ():
	return (CPM_CPCCR & CPM_CPCCR_MDIV_MASK) >> CPM_CPCCR_MDIV_BIT
static unsigned cpm_get_ldiv ():
	return (CPM_CPCCR & CPM_CPCCR_LDIV_MASK) >> CPM_CPCCR_LDIV_BIT
static unsigned cpm_get_udiv ():
	return (CPM_CPCCR & CPM_CPCCR_UDIV_MASK) >> CPM_CPCCR_UDIV_BIT
static unsigned cpm_get_i2sdiv ():
	return (CPM_I2SCDR & CPM_I2SCDR_I2SDIV_MASK) >> CPM_I2SCDR_I2SDIV_BIT
static unsigned cpm_get_pixdiv ():
	return (CPM_LPCDR & CPM_LPCDR_PIXDIV_MASK) >> CPM_LPCDR_PIXDIV_BIT
static unsigned cpm_get_mscdiv ():
	return (CPM_MSCCDR & CPM_MSCCDR_MSCDIV_MASK) >> CPM_MSCCDR_MSCDIV_BIT
static unsigned cpm_get_uhcdiv ():
	return (CPM_UHCCDR & CPM_UHCCDR_UHCDIV_MASK) >> CPM_UHCCDR_UHCDIV_BIT
static unsigned cpm_get_ssidiv ():
	return (CPM_SSICDR & CPM_SSICDR_SSIDIV_MASK) >> CPM_SSICDR_SSIDIV_BIT

static void cpm_set_cdiv (unsigned v):
	CPM_CPCCR = (CPM_CPCCR & ~CPM_CPCCR_CDIV_MASK) | (v << (CPM_CPCCR_CDIV_BIT))
static void cpm_set_hdiv (unsigned v):
	CPM_CPCCR = (CPM_CPCCR & ~CPM_CPCCR_HDIV_MASK) | (v << (CPM_CPCCR_HDIV_BIT))
static void cpm_set_pdiv (unsigned v):
	CPM_CPCCR = (CPM_CPCCR & ~CPM_CPCCR_PDIV_MASK) | (v << (CPM_CPCCR_PDIV_BIT))
static void cpm_set_mdiv (unsigned v):
	CPM_CPCCR = (CPM_CPCCR & ~CPM_CPCCR_MDIV_MASK) | (v << (CPM_CPCCR_MDIV_BIT))
static void cpm_set_ldiv (unsigned v):
	CPM_CPCCR = (CPM_CPCCR & ~CPM_CPCCR_LDIV_MASK) | (v << (CPM_CPCCR_LDIV_BIT))
static void cpm_set_udiv (unsigned v):
	CPM_CPCCR = (CPM_CPCCR & ~CPM_CPCCR_UDIV_MASK) | (v << (CPM_CPCCR_UDIV_BIT))
static void cpm_set_i2sdiv (unsigned v):
	CPM_I2SCDR = (CPM_I2SCDR & ~CPM_I2SCDR_I2SDIV_MASK) | (v << (CPM_I2SCDR_I2SDIV_BIT))
static void cpm_set_pixdiv (unsigned v):
	CPM_LPCDR = (CPM_LPCDR & ~CPM_LPCDR_PIXDIV_MASK) | (v << (CPM_LPCDR_PIXDIV_BIT))
static void cpm_set_mscdiv (unsigned v):
	CPM_MSCCDR = (CPM_MSCCDR & ~CPM_MSCCDR_MSCDIV_MASK) | (v << (CPM_MSCCDR_MSCDIV_BIT))
static void cpm_set_uhcdiv (unsigned v):
	CPM_UHCCDR = (CPM_UHCCDR & ~CPM_UHCCDR_UHCDIV_MASK) | (v << (CPM_UHCCDR_UHCDIV_BIT))
static void cpm_ssiclk_select_exclk ():
	CPM_SSICDR &= ~CPM_SSICDR_SCS
static void cpm_ssiclk_select_pllout ():
	CPM_SSICDR |= CPM_SSICDR_SCS
static void cpm_set_ssidiv (unsigned v):
	CPM_SSICDR = (CPM_SSICDR & ~CPM_SSICDR_SSIDIV_MASK) | ((v) << (CPM_SSICDR_SSIDIV_BIT))

#define cpm_select_i2sclk_exclk()	(CPM_CPCCR &= ~CPM_CPCCR_I2CS)
#define cpm_select_i2sclk_pll()	(CPM_CPCCR |= CPM_CPCCR_I2CS)
#define cpm_enable_cko()		(CPM_CPCCR |= CPM_CPCCR_CLKOEN)
#define cpm_select_usbclk_exclk()	(CPM_CPCCR &= ~CPM_CPCCR_UCS)
#define cpm_select_usbclk_pll()	(CPM_CPCCR |= CPM_CPCCR_UCS)
#define cpm_enable_pll_change()	(CPM_CPCCR |= CPM_CPCCR_CE)
#define cpm_pllout_direct()		(CPM_CPCCR |= CPM_CPCCR_PCS)
#define cpm_pllout_div2()		(CPM_CPCCR &= ~CPM_CPCCR_PCS)

#define cpm_pll_is_on()		(CPM_CPPCR & CPM_CPPCR_PLLS)
#define cpm_pll_bypass()		(CPM_CPPCR |= CPM_CPPCR_PLLBP)
#define cpm_pll_enable()		(CPM_CPPCR |= CPM_CPPCR_PLLEN)

#define cpm_get_cclk_doze_duty() ((CPM_LCR & CPM_LCR_DOZE_DUTY_MASK) >> CPM_LCR_DOZE_DUTY_BIT)
#define cpm_set_cclk_doze_duty(v) (CPM_LCR = (CPM_LCR & ~CPM_LCR_DOZE_DUTY_MASK) | ((v) << (CPM_LCR_DOZE_DUTY_BIT)))

#define cpm_doze_mode()		(CPM_LCR |= CPM_LCR_DOZE_ON)
#define cpm_idle_mode() (CPM_LCR = (CPM_LCR & ~CPM_LCR_LPM_MASK) | CPM_LCR_LPM_IDLE)
#define cpm_sleep_mode() (CPM_LCR = (CPM_LCR & ~CPM_LCR_LPM_MASK) | CPM_LCR_LPM_SLEEP)

#define cpm_stop_all() 	(CPM_CLKGR = 0x7fff)
#define cpm_stop_uart1()	(CPM_CLKGR |= CPM_CLKGR_UART1)
#define cpm_stop_uhc()	(CPM_CLKGR |= CPM_CLKGR_UHC)
#define cpm_stop_ipu()	(CPM_CLKGR |= CPM_CLKGR_IPU)
#define cpm_stop_dmac()	(CPM_CLKGR |= CPM_CLKGR_DMAC)
#define cpm_stop_udc()	(CPM_CLKGR |= CPM_CLKGR_UDC)
#define cpm_stop_lcd()	(CPM_CLKGR |= CPM_CLKGR_LCD)
#define cpm_stop_cim()	(CPM_CLKGR |= CPM_CLKGR_CIM)
#define cpm_stop_sadc()	(CPM_CLKGR |= CPM_CLKGR_SADC)
#define cpm_stop_msc()	(CPM_CLKGR |= CPM_CLKGR_MSC)
#define cpm_stop_aic1()	(CPM_CLKGR |= CPM_CLKGR_AIC1)
#define cpm_stop_aic2()	(CPM_CLKGR |= CPM_CLKGR_AIC2)
#define cpm_stop_ssi()	(CPM_CLKGR |= CPM_CLKGR_SSI)
#define cpm_stop_i2c()	(CPM_CLKGR |= CPM_CLKGR_I2C)
#define cpm_stop_rtc()	(CPM_CLKGR |= CPM_CLKGR_RTC)
#define cpm_stop_tcu()	(CPM_CLKGR |= CPM_CLKGR_TCU)
#define cpm_stop_uart0()	(CPM_CLKGR |= CPM_CLKGR_UART0)

#define cpm_start_all() 	(CPM_CLKGR = 0x0)
#define cpm_start_uart1()	(CPM_CLKGR &= ~CPM_CLKGR_UART1)
#define cpm_start_uhc()	(CPM_CLKGR &= ~CPM_CLKGR_UHC)
#define cpm_start_ipu()	(CPM_CLKGR &= ~CPM_CLKGR_IPU)
#define cpm_start_dmac()	(CPM_CLKGR &= ~CPM_CLKGR_DMAC)
#define cpm_start_udc()	(CPM_CLKGR &= ~CPM_CLKGR_UDC)
#define cpm_start_lcd()	(CPM_CLKGR &= ~CPM_CLKGR_LCD)
#define cpm_start_cim()	(CPM_CLKGR &= ~CPM_CLKGR_CIM)
#define cpm_start_sadc()	(CPM_CLKGR &= ~CPM_CLKGR_SADC)
#define cpm_start_msc()	(CPM_CLKGR &= ~CPM_CLKGR_MSC)
#define cpm_start_aic1()	(CPM_CLKGR &= ~CPM_CLKGR_AIC1)
#define cpm_start_aic2()	(CPM_CLKGR &= ~CPM_CLKGR_AIC2)
#define cpm_start_ssi()	(CPM_CLKGR &= ~CPM_CLKGR_SSI)
#define cpm_start_i2c()	(CPM_CLKGR &= ~CPM_CLKGR_I2C)
#define cpm_start_rtc()	(CPM_CLKGR &= ~CPM_CLKGR_RTC)
#define cpm_start_tcu()	(CPM_CLKGR &= ~CPM_CLKGR_TCU)
#define cpm_start_uart0()	(CPM_CLKGR &= ~CPM_CLKGR_UART0)

#define cpm_get_o1st() ((CPM_SCR & CPM_SCR_O1ST_MASK) >> CPM_SCR_O1ST_BIT)
#define cpm_set_o1st(v) (CPM_SCR = (CPM_SCR & ~CPM_SCR_O1ST_MASK) | ((v) << (CPM_SCR_O1ST_BIT)))
#define cpm_suspend_usbphy()		(CPM_SCR |= CPM_SCR_USBPHY_SUSPEND)
#define cpm_enable_osc_in_sleep()	(CPM_SCR |= CPM_SCR_OSC_ENABLE)

// PLL output frequency
static unsigned cpm_get_pllout ():
	unsigned m, n, no, pllout
	unsigned cppcr = CPM_CPPCR
	unsigned od[4] = {1, 2, 2, 4}
	if (cppcr & CPM_CPPCR_PLLEN) && !(cppcr & CPM_CPPCR_PLLBP):
		m = cpm_get_pllm () + 2
		n = cpm_get_plln () + 2
		no = od[cpm_get_pllod ()]
		pllout = JZ_EXTAL * m / n / no
	else:
		pllout = JZ_EXTAL
	return pllout

// PLL output frequency for MSC/I2S/LCD/USB
static unsigned cpm_get_pllout2 ():
	if CPM_CPCCR & CPM_CPCCR_PCS:
		return cpm_get_pllout ()
	else:
		return cpm_get_pllout () / 2

// CPU core clock
static unsigned cpm_get_cclk ():
	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32}
	return cpm_get_pllout () / div[cpm_get_cdiv ()]

// AHB system bus clock
static unsigned cpm_get_hclk ():
	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32}
	return cpm_get_pllout () / div[cpm_get_hdiv ()]

// Memory bus clock
static unsigned cpm_get_mclk ():
	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32}
	return cpm_get_pllout () / div[cpm_get_mdiv ()]

// APB peripheral bus clock
static unsigned cpm_get_pclk ():
	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32}
	return cpm_get_pllout () / div[cpm_get_pdiv ()]

// LCDC module clock
static unsigned cpm_get_lcdclk ():
	return cpm_get_pllout2 () / (cpm_get_ldiv () + 1)

// LCD pixel clock
static unsigned cpm_get_pixclk ():
	return cpm_get_pllout2 () / (cpm_get_pixdiv () + 1)

// I2S clock
static unsigned cpm_get_i2sclk ():
	if CPM_CPCCR & CPM_CPCCR_I2CS:
		return cpm_get_pllout2 () / (cpm_get_i2sdiv () + 1)
	else:
		return JZ_EXTAL

// USB clock
static unsigned cpm_get_usbclk ():
	if CPM_CPCCR & CPM_CPCCR_UCS:
		return cpm_get_pllout2 () / (cpm_get_udiv () + 1)
	else:
		return JZ_EXTAL

// MSC clock
static unsigned cpm_get_mscclk ():
	return cpm_get_pllout2 () / (cpm_get_mscdiv () + 1)

// EXTAL clock for UART,I2C,SSI,TCU,USB-PHY
static unsigned cpm_get_extalclk ():
	return JZ_EXTAL

// RTC clock for CPM,INTC,RTC,TCU,WDT
static unsigned cpm_get_rtcclk ():
	return RTC_CLOCK

// Output 24MHz for SD and 16MHz for MMC. 
static inline void cpm_select_msc_clk (int sd):
	unsigned int pllout2 = cpm_get_pllout2 ()
	unsigned int div = 0
	if sd:
		div = pllout2 / 24000000
	else:
		div = pllout2 / 16000000
	CPM_MSCCDR = div - 1


//**************************************************************************
// TCU
//**************************************************************************
// where 'n' is the TCU channel
#define tcu_select_extalclk(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~(TCU_TCSR_EXT_EN | TCU_TCSR_RTC_EN | TCU_TCSR_PCK_EN)) | TCU_TCSR_EXT_EN)
#define tcu_select_rtcclk(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~(TCU_TCSR_EXT_EN | TCU_TCSR_RTC_EN | TCU_TCSR_PCK_EN)) | TCU_TCSR_RTC_EN)
#define tcu_select_pclk(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~(TCU_TCSR_EXT_EN | TCU_TCSR_RTC_EN | TCU_TCSR_PCK_EN)) | TCU_TCSR_PCK_EN)

#define tcu_select_clk_div1(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~TCU_TCSR_PRESCALE_MASK) | TCU_TCSR_PRESCALE1)
#define tcu_select_clk_div4(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~TCU_TCSR_PRESCALE_MASK) | TCU_TCSR_PRESCALE4)
#define tcu_select_clk_div16(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~TCU_TCSR_PRESCALE_MASK) | TCU_TCSR_PRESCALE16)
#define tcu_select_clk_div64(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~TCU_TCSR_PRESCALE_MASK) | TCU_TCSR_PRESCALE64)
#define tcu_select_clk_div256(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~TCU_TCSR_PRESCALE_MASK) | TCU_TCSR_PRESCALE256)
#define tcu_select_clk_div1024(n) (TCU_TCSR((n)) = (TCU_TCSR((n)) & ~TCU_TCSR_PRESCALE_MASK) | TCU_TCSR_PRESCALE1024)

#define tcu_enable_pwm_output(n)	( TCU_TCSR((n)) |= TCU_TCSR_PWM_EN )
#define tcu_disable_pwm_output(n)	( TCU_TCSR((n)) &= ~TCU_TCSR_PWM_EN )

#define tcu_init_pwm_output_high(n)	( TCU_TCSR((n)) |= TCU_TCSR_PWM_INITL_HIGH )
#define tcu_init_pwm_output_low(n)	( TCU_TCSR((n)) &= ~TCU_TCSR_PWM_INITL_HIGH )

#define tcu_set_pwm_output_shutdown_graceful(n)	( TCU_TCSR((n)) &= ~TCU_TCSR_PWM_SD )
#define tcu_set_pwm_output_shutdown_abrupt(n)		( TCU_TCSR((n)) |= TCU_TCSR_PWM_SD )

#define tcu_start_counter(n)		( TCU_TESR |= (1 << (n)) )
#define tcu_stop_counter(n)		( TCU_TECR |= (1 << (n)) )

#define tcu_half_match_flag(n)	( TCU_TFR & (1 << ((n) + 16)) )
#define tcu_full_match_flag(n)	( TCU_TFR & (1 << (n)) )
#define tcu_set_half_match_flag(n)	( TCU_TFSR = (1 << ((n) + 16)) )
#define tcu_set_full_match_flag(n)	( TCU_TFSR = (1 << (n)) )
#define tcu_clear_half_match_flag(n)	( TCU_TFCR = (1 << ((n) + 16)) )
#define tcu_clear_full_match_flag(n)	( TCU_TFCR = (1 << (n)) )
#define tcu_mask_half_match_irq(n)	( TCU_TMSR = (1 << ((n) + 16)) )
#define tcu_mask_full_match_irq(n)	( TCU_TMSR = (1 << (n)) )
#define tcu_unmask_half_match_irq(n)	( TCU_TMCR = (1 << ((n) + 16)) )
#define tcu_unmask_full_match_irq(n)	( TCU_TMCR = (1 << (n)) )

#define tcu_wdt_clock_stopped()	( TCU_TSR & TCU_TSSR_WDTSC )
#define tcu_timer_clock_stopped(n)	( TCU_TSR & (1 << (n)) )

#define tcu_start_wdt_clock()		( TCU_TSCR = TCU_TSSR_WDTSC )
#define tcu_start_timer_clock(n)	( TCU_TSCR = (1 << (n)) )

#define tcu_stop_wdt_clock()		( TCU_TSSR = TCU_TSSR_WDTSC )
#define tcu_stop_timer_clock(n)	( TCU_TSSR = (1 << (n)) )

#define tcu_get_count(n)		( TCU_TCNT((n)) )
#define tcu_set_count(n,v)		( TCU_TCNT((n)) = (v) )
#define tcu_set_full_data(n,v)	( TCU_TDFR((n)) = (v) )
#define tcu_set_half_data(n,v)	( TCU_TDHR((n)) = (v) )


//**************************************************************************
// WDT
//**************************************************************************
#define wdt_start()			( WDT_TCER |= WDT_TCER_TCEN )
#define wdt_stop()			( WDT_TCER &= ~WDT_TCER_TCEN )
#define wdt_set_count(v)		( WDT_TCNT = (v) )
#define wdt_set_data(v)		( WDT_TDR = (v) )

#define wdt_select_extalclk() (WDT_TCSR = (WDT_TCSR & ~(WDT_TCSR_EXT_EN | WDT_TCSR_RTC_EN | WDT_TCSR_PCK_EN)) | WDT_TCSR_EXT_EN)
#define wdt_select_rtcclk() (WDT_TCSR = (WDT_TCSR & ~(WDT_TCSR_EXT_EN | WDT_TCSR_RTC_EN | WDT_TCSR_PCK_EN)) | WDT_TCSR_RTC_EN)
#define wdt_select_pclk() (WDT_TCSR = (WDT_TCSR & ~(WDT_TCSR_EXT_EN | WDT_TCSR_RTC_EN | WDT_TCSR_PCK_EN)) | WDT_TCSR_PCK_EN)

#define wdt_select_clk_div1() (WDT_TCSR = (WDT_TCSR & ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE1)
#define wdt_select_clk_div4() (WDT_TCSR = (WDT_TCSR & ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE4)
#define wdt_select_clk_div16() (WDT_TCSR = (WDT_TCSR & ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE16)
#define wdt_select_clk_div64() (WDT_TCSR = (WDT_TCSR & ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE64)
#define wdt_select_clk_div256() (WDT_TCSR = (WDT_TCSR & ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE256)
#define wdt_select_clk_div1024() (WDT_TCSR = (WDT_TCSR & ~WDT_TCSR_PRESCALE_MASK) | WDT_TCSR_PRESCALE1024)


//**************************************************************************
// UART
//**************************************************************************

#define uart_enable(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_FCR) |= UARTFCR_UUE | UARTFCR_FE )
#define uart_disable(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_FCR) = ~UARTFCR_UUE )

#define uart_enable_transmit_irq(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_IER) |= UARTIER_TIE )
#define uart_disable_transmit_irq(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_IER) &= ~UARTIER_TIE )

#define uart_enable_receive_irq(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_IER) |= UARTIER_RIE | UARTIER_RLIE | UARTIER_RTIE )
#define uart_disable_receive_irq(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_IER) &= ~(UARTIER_RIE | UARTIER_RLIE | UARTIER_RTIE) )

#define uart_enable_loopback(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_MCR) |= UARTMCR_LOOP )
#define uart_disable_loopback(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_MCR) &= ~UARTMCR_LOOP )

#define uart_set_8n1(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_LCR) = UARTLCR_WLEN_8 )

static void uart_set_baud (unsigned n, unsigned devclk, unsigned baud):
	REG8 (UART_BASE + UART_OFF*(n) + OFF_LCR) |= UARTLCR_DLAB
	REG8 (UART_BASE + UART_OFF*(n) + OFF_DLLR) = (devclk / 16 / baud) & 0xff
	REG8 (UART_BASE + UART_OFF*(n) + OFF_DLHR) = ((devclk / 16 / baud) >> 8) & 0xff
	REG8 (UART_BASE + UART_OFF*(n) + OFF_LCR) &= ~UARTLCR_DLAB

#define uart_parity_error(n) ( (REG8(UART_BASE + UART_OFF*(n) + OFF_LSR) & UARTLSR_PER) != 0 )

#define uart_clear_errors(n) ( REG8(UART_BASE + UART_OFF*(n) + OFF_LSR) &= ~(UARTLSR_ORER | UARTLSR_BRK | UARTLSR_FER | UARTLSR_PER | UARTLSR_RFER) )

#define uart_transmit_fifo_empty(n) ( (REG8(UART_BASE + UART_OFF*(n) + OFF_LSR) & UARTLSR_TDRQ) != 0 )

#define uart_transmit_end(n) ( (REG8(UART_BASE + UART_OFF*(n) + OFF_LSR) & UARTLSR_TEMT) != 0 )

#define uart_transmit_char(n, ch) REG8(UART_BASE + UART_OFF*(n) + OFF_TDR) = (ch)

#define uart_receive_fifo_full(n) ( (REG8(UART_BASE + UART_OFF*(n) + OFF_LSR) & UARTLSR_DR) != 0 )

#define uart_receive_ready(n) ( (REG8(UART_BASE + UART_OFF*(n) + OFF_LSR) & UARTLSR_DR) != 0 )

#define uart_receive_char(n) REG8(UART_BASE + UART_OFF*(n) + OFF_RDR)

#define uart_disable_irda() ( REG8(IRDA_BASE + OFF_SIRCR) &= ~(SIRCR_TSIRE | SIRCR_RSIRE) )
#define uart_enable_irda() /* Tx high pulse as 0, Rx low pulse as 0 */ ( REG8(IRDA_BASE + OFF_SIRCR) = SIRCR_TSIRE | SIRCR_RSIRE | SIRCR_RXPL | SIRCR_TPWS )


//**************************************************************************
// DMAC
//**************************************************************************

// n is the DMA channel (0 - 5)

#define dmac_enable_module() ( DMAC_DMACR |= DMAC_DMACR_DMAE | DMAC_DMACR_PR_RR )
#define dmac_disable_module() ( DMAC_DMACR &= ~DMAC_DMACR_DMAE )

// p=0,1,2,3
static void dmac_set_priority (unsigned p):
	DMAC_DMACR &= ~DMAC_DMACR_PR_MASK
	DMAC_DMACR |= ((p) << DMAC_DMACR_PR_BIT)

#define dmac_test_halt_error() ( DMAC_DMACR & DMAC_DMACR_HLT )
#define dmac_test_addr_error() ( DMAC_DMACR & DMAC_DMACR_AR )

#define dmac_enable_descriptor(n) ( DMAC_DCCSR((n)) &= ~DMAC_DCCSR_NDES )
#define dmac_disable_descriptor(n) ( DMAC_DCCSR((n)) |= DMAC_DCCSR_NDES )

#define dmac_enable_channel(n) ( DMAC_DCCSR((n)) |= DMAC_DCCSR_EN )
#define dmac_disable_channel(n) ( DMAC_DCCSR((n)) &= ~DMAC_DCCSR_EN )
#define dmac_channel_enabled(n) ( DMAC_DCCSR((n)) & DMAC_DCCSR_EN )

#define dmac_channel_enable_irq(n) ( DMAC_DCMD((n)) |= DMAC_DCMD_TIE )
#define dmac_channel_disable_irq(n) ( DMAC_DCMD((n)) &= ~DMAC_DCMD_TIE )

#define dmac_channel_transmit_halt_detected(n) (  DMAC_DCCSR((n)) & DMAC_DCCSR_HLT )
#define dmac_channel_transmit_end_detected(n) (  DMAC_DCCSR((n)) & DMAC_DCCSR_TT )
#define dmac_channel_address_error_detected(n) (  DMAC_DCCSR((n)) & DMAC_DCCSR_AR )
#define dmac_channel_count_terminated_detected(n) (  DMAC_DCCSR((n)) & DMAC_DCCSR_CT )
#define dmac_channel_descriptor_invalid_detected(n) (  DMAC_DCCSR((n)) & DMAC_DCCSR_INV )

#define dmac_channel_clear_transmit_halt(n) (  DMAC_DCCSR(n) &= ~DMAC_DCCSR_HLT )
#define dmac_channel_clear_transmit_end(n) (  DMAC_DCCSR(n) &= ~DMAC_DCCSR_TT )
#define dmac_channel_clear_address_error(n) (  DMAC_DCCSR(n) &= ~DMAC_DCCSR_AR )
#define dmac_channel_clear_count_terminated(n) (  DMAC_DCCSR((n)) &= ~DMAC_DCCSR_CT )
#define dmac_channel_clear_descriptor_invalid(n) (  DMAC_DCCSR((n)) &= ~DMAC_DCCSR_INV )

#define dmac_channel_set_single_mode(n) (  DMAC_DCMD((n)) &= ~DMAC_DCMD_TM )
#define dmac_channel_set_block_mode(n) (  DMAC_DCMD((n)) |= DMAC_DCMD_TM )

static void dmac_channel_set_transfer_unit_32bit (unsigned n):
	DMAC_DCMD((n)) &= ~DMAC_DCMD_DS_MASK
	DMAC_DCMD((n)) |= DMAC_DCMD_DS_32BIT

static void dmac_channel_set_transfer_unit_16bit (unsigned n):
	DMAC_DCMD((n)) &= ~DMAC_DCMD_DS_MASK
	DMAC_DCMD((n)) |= DMAC_DCMD_DS_16BIT

static void dmac_channel_set_transfer_unit_8bit (unsigned n):
	DMAC_DCMD((n)) &= ~DMAC_DCMD_DS_MASK
	DMAC_DCMD((n)) |= DMAC_DCMD_DS_8BIT

static void dmac_channel_set_transfer_unit_16byte (unsigned n):
	DMAC_DCMD((n)) &= ~DMAC_DCMD_DS_MASK
	DMAC_DCMD((n)) |= DMAC_DCMD_DS_16BYTE

static void dmac_channel_set_transfer_unit_32byte (unsigned n):
	DMAC_DCMD((n)) &= ~DMAC_DCMD_DS_MASK
	DMAC_DCMD((n)) |= DMAC_DCMD_DS_32BYTE

// w=8,16,32
#define dmac_channel_set_dest_port_width(n,w) do { DMAC_DCMD((n)) &= ~DMAC_DCMD_DWDH_MASK; DMAC_DCMD((n)) |= DMAC_DCMD_DWDH_##w; } while (0)

// w=8,16,32
#define dmac_channel_set_src_port_width(n,v) do { DMAC_DCMD((n)) &= ~DMAC_DCMD_SWDH_MASK; DMAC_DCMD((n)) |= DMAC_DCMD_SWDH_##w; } while (0)

// v=0-15
static void dmac_channel_set_rdil(unsigned n, unsigned v):
	DMAC_DCMD((n)) &= ~DMAC_DCMD_RDIL_MASK
	DMAC_DCMD((n)) |= ((v) << DMAC_DCMD_RDIL_BIT)

#define dmac_channel_dest_addr_fixed(n) (  DMAC_DCMD((n)) &= ~DMAC_DCMD_DAI )
#define dmac_channel_dest_addr_increment(n) (  DMAC_DCMD((n)) |= DMAC_DCMD_DAI )

#define dmac_channel_src_addr_fixed(n) (  DMAC_DCMD((n)) &= ~DMAC_DCMD_SAI )
#define dmac_channel_src_addr_increment(n) (  DMAC_DCMD((n)) |= DMAC_DCMD_SAI )

#define dmac_channel_set_doorbell(n) (  DMAC_DMADBSR = (1 << (n)) )

#define dmac_channel_irq_detected(n)  ( DMAC_DMAIPR & (1 << (n)) )
#define dmac_channel_ack_irq(n)       ( DMAC_DMAIPR &= ~(1 << (n)) )


//**************************************************************************
// AIC (AC'97 & I2S Controller)
//**************************************************************************

#define aic_enable()		( AIC_FR |= AIC_FR_ENB )
#define aic_disable()		( AIC_FR &= ~AIC_FR_ENB )

#define aic_select_ac97()	( AIC_FR &= ~AIC_FR_AUSEL )
#define aic_select_i2s()	( AIC_FR |= AIC_FR_AUSEL )

#define aic_play_zero()	( AIC_FR &= ~AIC_FR_LSMP )
#define aic_play_lastsample()	( AIC_FR |= AIC_FR_LSMP )

#define i2s_as_master()	( AIC_FR |= AIC_FR_BCKD | AIC_FR_SYNCD )
#define i2s_as_slave()	( AIC_FR &= ~(AIC_FR_BCKD | AIC_FR_SYNCD) )
#define aic_reset_status()          ( AIC_FR & AIC_FR_RST )

static void aic_reset():
        AIC_FR |= AIC_FR_RST

static void aic_set_transmit_trigger (unsigned n):
	AIC_FR &= ~AIC_FR_TFTH_MASK
	AIC_FR |= ((n) << AIC_FR_TFTH_BIT)

static void aic_set_receive_trigger (unsigned n):
	AIC_FR &= ~AIC_FR_RFTH_MASK
	AIC_FR |= ((n) << AIC_FR_RFTH_BIT)

#define aic_enable_record()	( AIC_CR |= AIC_CR_EREC )
#define aic_disable_record()	( AIC_CR &= ~AIC_CR_EREC )
#define aic_enable_replay()	( AIC_CR |= AIC_CR_ERPL )
#define aic_disable_replay()	( AIC_CR &= ~AIC_CR_ERPL )
#define aic_enable_loopback()	( AIC_CR |= AIC_CR_ENLBF )
#define aic_disable_loopback() ( AIC_CR &= ~AIC_CR_ENLBF )

#define aic_flush_fifo()	( AIC_CR |= AIC_CR_FLUSH )
#define aic_unflush_fifo()	( AIC_CR &= ~AIC_CR_FLUSH )

#define aic_enable_transmit_intr() ( AIC_CR |= (AIC_CR_ETFS | AIC_CR_ETUR) )
#define aic_disable_transmit_intr() ( AIC_CR &= ~(AIC_CR_ETFS | AIC_CR_ETUR) )
#define aic_enable_receive_intr() ( AIC_CR |= (AIC_CR_ERFS | AIC_CR_EROR) )
#define aic_disable_receive_intr() ( AIC_CR &= ~(AIC_CR_ERFS | AIC_CR_EROR) )

#define aic_enable_transmit_dma()  ( AIC_CR |= AIC_CR_TDMS )
#define aic_disable_transmit_dma() ( AIC_CR &= ~AIC_CR_TDMS )
#define aic_enable_receive_dma()   ( AIC_CR |= AIC_CR_RDMS )
#define aic_disable_receive_dma()  ( AIC_CR &= ~AIC_CR_RDMS )

#define aic_enable_mono2stereo()   ( AIC_CR |= AIC_CR_M2S )
#define aic_disable_mono2stereo()  ( AIC_CR &= ~AIC_CR_M2S )
#define aic_enable_byteswap()      ( AIC_CR |= AIC_CR_ENDSW )
#define aic_disable_byteswap()     ( AIC_CR &= ~AIC_CR_ENDSW )
#define aic_enable_unsignadj()     ( AIC_CR |= AIC_CR_AVSTSU )
#define aic_disable_unsignadj()    ( AIC_CR &= ~AIC_CR_AVSTSU )

#define AC97_PCM_XS_L_FRONT   	AIC_ACCR1_XS_SLOT3
#define AC97_PCM_XS_R_FRONT   	AIC_ACCR1_XS_SLOT4
#define AC97_PCM_XS_CENTER    	AIC_ACCR1_XS_SLOT6
#define AC97_PCM_XS_L_SURR    	AIC_ACCR1_XS_SLOT7
#define AC97_PCM_XS_R_SURR    	AIC_ACCR1_XS_SLOT8
#define AC97_PCM_XS_LFE       	AIC_ACCR1_XS_SLOT9

#define AC97_PCM_RS_L_FRONT   	AIC_ACCR1_RS_SLOT3
#define AC97_PCM_RS_R_FRONT   	AIC_ACCR1_RS_SLOT4
#define AC97_PCM_RS_CENTER    	AIC_ACCR1_RS_SLOT6
#define AC97_PCM_RS_L_SURR    	AIC_ACCR1_RS_SLOT7
#define AC97_PCM_RS_R_SURR    	AIC_ACCR1_RS_SLOT8
#define AC97_PCM_RS_LFE       	AIC_ACCR1_RS_SLOT9

#define ac97_set_xs_none()	( AIC_ACCR1 &= ~AIC_ACCR1_XS_MASK )
static void ac97_set_xs_mono():
	AIC_ACCR1 &= ~AIC_ACCR1_XS_MASK
	AIC_ACCR1 |= AC97_PCM_XS_R_FRONT
static void ac97_set_xs_stereo():
	AIC_ACCR1 &= ~AIC_ACCR1_XS_MASK
	AIC_ACCR1 |= AC97_PCM_XS_L_FRONT | AC97_PCM_XS_R_FRONT

// In fact, only stereo is support now.
#define ac97_set_rs_none()	( AIC_ACCR1 &= ~AIC_ACCR1_RS_MASK )
static void ac97_set_rs_mono():
	AIC_ACCR1 &= ~AIC_ACCR1_RS_MASK
	AIC_ACCR1 |= AC97_PCM_RS_R_FRONT
static void ac97_set_rs_stereo():
	AIC_ACCR1 &= ~AIC_ACCR1_RS_MASK
	AIC_ACCR1 |= AC97_PCM_RS_L_FRONT | AC97_PCM_RS_R_FRONT

static void ac97_warm_reset_codec():
	AIC_ACCR2 |= AIC_ACCR2_SA
	AIC_ACCR2 |= AIC_ACCR2_SS
	//udelay(2) // TODO
	AIC_ACCR2 &= ~AIC_ACCR2_SS
	AIC_ACCR2 &= ~AIC_ACCR2_SA

static void ac97_cold_reset_codec():
	AIC_ACCR2 |=  AIC_ACCR2_SR
	//udelay(2) // TODO
	AIC_ACCR2 &= ~AIC_ACCR2_SR

// n=8,16,18,20
#define ac97_set_iass(n) ( AIC_ACCR2 = (AIC_ACCR2 & ~AIC_ACCR2_IASS_MASK) | AIC_ACCR2_IASS_##n##BIT )
#define ac97_set_oass(n) ( AIC_ACCR2 = (AIC_ACCR2 & ~AIC_ACCR2_OASS_MASK) | AIC_ACCR2_OASS_##n##BIT )

#define i2s_select_i2s()            ( AIC_I2SCR &= ~AIC_I2SCR_AMSL )
#define i2s_select_msbjustified()   ( AIC_I2SCR |= AIC_I2SCR_AMSL )

// n=8,16,18,20,24
//#define i2s_set_sample_size(n) ( AIC_I2SCR |= (AIC_I2SCR & ~AIC_I2SCR_WL_MASK) | AIC_I2SCR_WL_##n##BIT )

#define i2s_set_oss_sample_size(n) ( AIC_CR = (AIC_CR & ~AIC_CR_OSS_MASK) | AIC_CR_OSS_##n##BIT )
#define i2s_set_iss_sample_size(n) ( AIC_CR = (AIC_CR & ~AIC_CR_ISS_MASK) | AIC_CR_ISS_##n##BIT )

#define i2s_stop_bitclk()   ( AIC_I2SCR |= AIC_I2SCR_STPBK )
#define i2s_start_bitclk()  ( AIC_I2SCR &= ~AIC_I2SCR_STPBK )

#define aic_transmit_request()  ( AIC_SR & AIC_SR_TFS )
#define aic_receive_request()   ( AIC_SR & AIC_SR_RFS )
#define aic_transmit_underrun() ( AIC_SR & AIC_SR_TUR )
#define aic_receive_overrun()   ( AIC_SR & AIC_SR_ROR )

#define aic_clear_errors()      ( AIC_SR &= ~(AIC_SR_TUR | AIC_SR_ROR) )

#define aic_get_transmit_resident() ( (AIC_SR & AIC_SR_TFL_MASK) >> AIC_SR_TFL_BIT )
#define aic_get_receive_count() ( (AIC_SR & AIC_SR_RFL_MASK) >> AIC_SR_RFL_BIT )

#define ac97_command_transmitted()     ( AIC_ACSR & AIC_ACSR_CADT )
#define ac97_status_received()         ( AIC_ACSR & AIC_ACSR_SADR )
#define ac97_status_receive_timeout()  ( AIC_ACSR & AIC_ACSR_RSTO )
#define ac97_codec_is_low_power_mode() ( AIC_ACSR & AIC_ACSR_CLPM )
#define ac97_codec_is_ready()          ( AIC_ACSR & AIC_ACSR_CRDY )
#define ac97_slot_error_detected()     ( AIC_ACSR & AIC_ACSR_SLTERR )
#define ac97_clear_slot_error()        ( AIC_ACSR &= ~AIC_ACSR_SLTERR )

#define i2s_is_busy()         ( AIC_I2SSR & AIC_I2SSR_BSY )

#define CODEC_READ_CMD	        (1 << 19)
#define CODEC_WRITE_CMD	        (0 << 19)
#define CODEC_REG_INDEX_BIT     12
#define CODEC_REG_INDEX_MASK	(0x7f << CODEC_REG_INDEX_BIT)	// 18:12
#define CODEC_REG_DATA_BIT      4
#define CODEC_REG_DATA_MASK	(0x0ffff << 4)	// 19:4

#define ac97_out_rcmd_addr(reg) 					(AIC_ACCAR = CODEC_READ_CMD | ((reg) << CODEC_REG_INDEX_BIT))

#define ac97_out_wcmd_addr(reg) 					(AIC_ACCAR = CODEC_WRITE_CMD | ((reg) << CODEC_REG_INDEX_BIT))

#define ac97_out_data(value) 						(AIC_ACCDR = ((value) << CODEC_REG_DATA_BIT))

#define ac97_in_data() ( (AIC_ACSDR & CODEC_REG_DATA_MASK) >> CODEC_REG_DATA_BIT )

#define ac97_in_status_addr() ( (AIC_ACSAR & CODEC_REG_INDEX_MASK) >> CODEC_REG_INDEX_BIT )

#define i2s_set_sample_rate(i2sclk, sync) ( AIC_I2SDIV = ((i2sclk) / (4*64)) / (sync) )

#define aic_write_tfifo(v)  ( AIC_DR = (v) )
#define aic_read_rfifo()    ( AIC_DR )

#define aic_internal_codec()  ( AIC_FR |= AIC_FR_ICDC ) 
#define aic_external_codec()  ( AIC_FR &= ~AIC_FR_ICDC )

//
// Define next ops for AC97 compatible
//

#define AC97_ACSR	AIC_ACSR

#define ac97_enable()		aic_enable(); aic_select_ac97()
#define ac97_disable()	aic_disable()
#define ac97_reset()		aic_reset()

#define ac97_set_transmit_trigger(n)	aic_set_transmit_trigger(n)
#define ac97_set_receive_trigger(n)	aic_set_receive_trigger(n)

#define ac97_enable_record()		aic_enable_record()
#define ac97_disable_record()		aic_disable_record()
#define ac97_enable_replay()		aic_enable_replay()
#define ac97_disable_replay()		aic_disable_replay()
#define ac97_enable_loopback()	aic_enable_loopback()
#define ac97_disable_loopback()	aic_disable_loopback()

#define ac97_enable_transmit_dma()	aic_enable_transmit_dma()
#define ac97_disable_transmit_dma()	aic_disable_transmit_dma()
#define ac97_enable_receive_dma()	aic_enable_receive_dma()
#define ac97_disable_receive_dma()	aic_disable_receive_dma()

#define ac97_transmit_request()	aic_transmit_request()
#define ac97_receive_request()	aic_receive_request()
#define ac97_transmit_underrun()	aic_transmit_underrun()
#define ac97_receive_overrun()	aic_receive_overrun()

#define ac97_clear_errors()		aic_clear_errors()

#define ac97_get_transmit_resident()	aic_get_transmit_resident()
#define ac97_get_receive_count()	aic_get_receive_count()

#define ac97_enable_transmit_intr()	aic_enable_transmit_intr()
#define ac97_disable_transmit_intr()	aic_disable_transmit_intr()
#define ac97_enable_receive_intr()	aic_enable_receive_intr()
#define ac97_disable_receive_intr()	aic_disable_receive_intr()

#define ac97_write_tfifo(v)		aic_write_tfifo(v)
#define ac97_read_rfifo()		aic_read_rfifo()

//
// Define next ops for I2S compatible
//

#define I2S_ACSR	AIC_I2SSR

#define i2s_enable()		 aic_enable(); aic_select_i2s()
#define i2s_disable()		aic_disable()
#define i2s_reset()		aic_reset()

#define i2s_set_transmit_trigger(n)	aic_set_transmit_trigger(n)
#define i2s_set_receive_trigger(n)	aic_set_receive_trigger(n)

#define i2s_enable_record()		aic_enable_record()
#define i2s_disable_record()		aic_disable_record()
#define i2s_enable_replay()		aic_enable_replay()
#define i2s_disable_replay()		aic_disable_replay()
#define i2s_enable_loopback()		aic_enable_loopback()
#define i2s_disable_loopback()	aic_disable_loopback()

#define i2s_enable_transmit_dma()	aic_enable_transmit_dma()
#define i2s_disable_transmit_dma()	aic_disable_transmit_dma()
#define i2s_enable_receive_dma()	aic_enable_receive_dma()
#define i2s_disable_receive_dma()	aic_disable_receive_dma()

#define i2s_transmit_request()	aic_transmit_request()
#define i2s_receive_request()		aic_receive_request()
#define i2s_transmit_underrun()	aic_transmit_underrun()
#define i2s_receive_overrun()		aic_receive_overrun()

#define i2s_clear_errors()		aic_clear_errors()

#define i2s_get_transmit_resident()	aic_get_transmit_resident()
#define i2s_get_receive_count()	aic_get_receive_count()

#define i2s_enable_transmit_intr()	aic_enable_transmit_intr()
#define i2s_disable_transmit_intr()	aic_disable_transmit_intr()
#define i2s_enable_receive_intr()	aic_enable_receive_intr()
#define i2s_disable_receive_intr()	aic_disable_receive_intr()

#define i2s_write_tfifo(v)		aic_write_tfifo(v)
#define i2s_read_rfifo()		aic_read_rfifo()

#define i2s_reset_codec()			do {						} while (0)

static void aic_use_internal_codec ():
	aic_internal_codec ()
	aic_select_i2s ()
	i2s_as_slave ()
	i2s_select_i2s ()
	cpm_select_i2sclk_exclk ()
	cpm_set_i2sdiv (1)

//**************************************************************************
// ICDC
//**************************************************************************
#define i2s_internal_codec()         aic_internal_codec()
#define i2s_external_codec()         aic_external_codec()

//**************************************************************************
// INTC
//**************************************************************************
#define intc_unmask_irq(n)	( INTC_IMCR = (1 << (n)) )
#define intc_mask_irq(n)	( INTC_IMSR = (1 << (n)) )
#define intc_ack_irq(n)	( INTC_IPR = (1 << (n)) )


//**************************************************************************
// I2C
//**************************************************************************

#define i2c_enable()		( I2C_CR |= I2C_CR_I2CE )
#define i2c_disable()		( I2C_CR &= ~I2C_CR_I2CE )

#define i2c_send_start()	( I2C_CR |= I2C_CR_STA )
#define i2c_send_stop()	( I2C_CR |= I2C_CR_STO )
#define i2c_send_ack()	( I2C_CR &= ~I2C_CR_AC )
#define i2c_send_nack()	( I2C_CR |= I2C_CR_AC )

#define i2c_set_drf()		( I2C_SR |= I2C_SR_DRF )
#define i2c_clear_drf()	( I2C_SR &= ~I2C_SR_DRF )
#define i2c_check_drf()	( I2C_SR & I2C_SR_DRF )

#define i2c_received_ack()	( !(I2C_SR & I2C_SR_ACKF) )
#define i2c_is_busy()		( I2C_SR & I2C_SR_BUSY )
#define i2c_transmit_ended()	( I2C_SR & I2C_SR_TEND )

#define i2c_set_clk(dev_clk, i2c_clk) ( I2C_GR = (dev_clk) / (16*(i2c_clk)) - 1 )

#define i2c_read()		( I2C_DR )
#define i2c_write(val)	( I2C_DR = (val) )


//**************************************************************************
// MSC
//**************************************************************************

#define msc_start_op() ( MSC_STRPCL = MSC_STRPCL_START_OP | MSC_STRPCL_CLOCK_CONTROL_START )

#define msc_set_resto(to) 	( MSC_RESTO = to )
#define msc_set_rdto(to) 	( MSC_RDTO = to )
#define msc_set_cmd(cmd) 	( MSC_CMD = cmd )
#define msc_set_arg(arg) 	( MSC_ARG = arg )
#define msc_set_nob(nob) 	( MSC_NOB = nob )
#define msc_get_nob() 	( MSC_NOB )
#define msc_set_blklen(len) 	( MSC_BLKLEN = len )
#define msc_set_cmdat(cmdat) 	( MSC_CMDAT = cmdat )
#define msc_set_cmdat_ioabort() 	( MSC_CMDAT |= MSC_CMDAT_IO_ABORT )
#define msc_clear_cmdat_ioabort() 	( MSC_CMDAT &= ~MSC_CMDAT_IO_ABORT )

static void msc_set_cmdat_bus_width1():
	MSC_CMDAT &= ~MSC_CMDAT_BUS_WIDTH_MASK
	MSC_CMDAT |= MSC_CMDAT_BUS_WIDTH_1BIT

static void msc_set_cmdat_bus_width4():
	MSC_CMDAT &= ~MSC_CMDAT_BUS_WIDTH_MASK
	MSC_CMDAT |= MSC_CMDAT_BUS_WIDTH_4BIT

#define msc_set_cmdat_dma_en() ( MSC_CMDAT |= MSC_CMDAT_DMA_EN )
#define msc_set_cmdat_init() 	( MSC_CMDAT |= MSC_CMDAT_INIT )
#define msc_set_cmdat_busy() 	( MSC_CMDAT |= MSC_CMDAT_BUSY )
#define msc_set_cmdat_stream() ( MSC_CMDAT |= MSC_CMDAT_STREAM_BLOCK )
#define msc_set_cmdat_block() ( MSC_CMDAT &= ~MSC_CMDAT_STREAM_BLOCK )
#define msc_set_cmdat_read() 	( MSC_CMDAT &= ~MSC_CMDAT_WRITE_READ )
#define msc_set_cmdat_write() ( MSC_CMDAT |= MSC_CMDAT_WRITE_READ )
#define msc_set_cmdat_data_en() ( MSC_CMDAT |= MSC_CMDAT_DATA_EN )

// r is MSC_CMDAT_RESPONSE_FORMAT_Rx or MSC_CMDAT_RESPONSE_FORMAT_NONE
static void msc_set_cmdat_res_format(unsigned r):
	MSC_CMDAT &= ~MSC_CMDAT_RESPONSE_MASK
	MSC_CMDAT |= (r)

#define msc_clear_cmdat() MSC_CMDAT &= ~( MSC_CMDAT_IO_ABORT | MSC_CMDAT_DMA_EN | MSC_CMDAT_INIT| MSC_CMDAT_BUSY | MSC_CMDAT_STREAM_BLOCK | MSC_CMDAT_WRITE_READ | MSC_CMDAT_DATA_EN | MSC_CMDAT_RESPONSE_MASK )

#define msc_get_imask() 		( MSC_IMASK )
#define msc_mask_all_intrs() 		( MSC_IMASK = 0xff )
#define msc_unmask_all_intrs() 	( MSC_IMASK = 0x00 )
#define msc_mask_rd() 		( MSC_IMASK |= MSC_IMASK_RXFIFO_RD_REQ )
#define msc_unmask_rd() 		( MSC_IMASK &= ~MSC_IMASK_RXFIFO_RD_REQ )
#define msc_mask_wr() 		( MSC_IMASK |= MSC_IMASK_TXFIFO_WR_REQ )
#define msc_unmask_wr() 		( MSC_IMASK &= ~MSC_IMASK_TXFIFO_WR_REQ )
#define msc_mask_endcmdres() 		( MSC_IMASK |= MSC_IMASK_END_CMD_RES )
#define msc_unmask_endcmdres() 	( MSC_IMASK &= ~MSC_IMASK_END_CMD_RES )
#define msc_mask_datatrandone() 	( MSC_IMASK |= MSC_IMASK_DATA_TRAN_DONE )
#define msc_unmask_datatrandone() 	( MSC_IMASK &= ~MSC_IMASK_DATA_TRAN_DONE )
#define msc_mask_prgdone() 		( MSC_IMASK |= MSC_IMASK_PRG_DONE )
#define msc_unmask_prgdone() 		( MSC_IMASK &= ~MSC_IMASK_PRG_DONE )

// n=0,1,2,3,4,5,6,7
#define msc_set_clkrt(n) 	(MSC_CLKRT = n)

#define msc_get_ireg() 		( MSC_IREG )
#define msc_ireg_rd() 		( MSC_IREG & MSC_IREG_RXFIFO_RD_REQ )
#define msc_ireg_wr() 		( MSC_IREG & MSC_IREG_TXFIFO_WR_REQ )
#define msc_ireg_end_cmd_res() 	( MSC_IREG & MSC_IREG_END_CMD_RES )
#define msc_ireg_data_tran_done() 	( MSC_IREG & MSC_IREG_DATA_TRAN_DONE )
#define msc_ireg_prg_done() 		( MSC_IREG & MSC_IREG_PRG_DONE )
#define msc_ireg_clear_end_cmd_res() 	( MSC_IREG = MSC_IREG_END_CMD_RES )
#define msc_ireg_clear_data_tran_done() ( MSC_IREG = MSC_IREG_DATA_TRAN_DONE )
#define msc_ireg_clear_prg_done() 	( MSC_IREG = MSC_IREG_PRG_DONE )

#define msc_get_stat() 		( MSC_STAT )
#define msc_stat_not_end_cmd_res() 	( (MSC_STAT & MSC_STAT_END_CMD_RES) == 0)
#define msc_stat_crc_err() ( MSC_STAT & (MSC_STAT_CRC_RES_ERR | MSC_STAT_CRC_READ_ERROR | MSC_STAT_CRC_WRITE_ERROR_YES) )
#define msc_stat_res_crc_err() 	( MSC_STAT & MSC_STAT_CRC_RES_ERR )
#define msc_stat_rd_crc_err() 	( MSC_STAT & MSC_STAT_CRC_READ_ERROR )
#define msc_stat_wr_crc_err() 	( MSC_STAT & MSC_STAT_CRC_WRITE_ERROR_YES )
#define msc_stat_resto_err() 		( MSC_STAT & MSC_STAT_TIME_OUT_RES )
#define msc_stat_rdto_err() 		( MSC_STAT & MSC_STAT_TIME_OUT_READ )

#define msc_rd_resfifo() 		( MSC_RES )
#define msc_rd_rxfifo()  		( MSC_RXFIFO )
#define msc_wr_txfifo(v)  		( MSC_TXFIFO = v )

#define msc_start_clk() 					(MSC_STRPCL = MSC_STRPCL_CLOCK_CONTROL_START)

#define MMC_CLK 19169200
#define SD_CLK  24576000

// msc_clk should little than pclk and little than clk retrieve from card
static unsigned msc_calc_clk_divisor (bool sd, unsigned dev_clk, unsigned msc_clk):
	unsigned int rate, pclk, i
	pclk = dev_clk
	rate = sd ? SD_CLK : MMC_CLK
	if msc_clk && msc_clk < pclk:
		pclk = msc_clk
	i = 0
	while pclk < rate:
		i ++
		rate >>= 1
	return i

// divide rate to little than or equal to 400kHz
static unsigned msc_calc_slow_clk_divisor (bool sd):
	unsigned rate, i
	rate = (sd ? SD_CLK : MMC_CLK) / 1000 / 400
	i = 0
	while rate > 0:
		rate >>= 1
		++i
	return i


//**************************************************************************
// SSI
//**************************************************************************

#define ssi_enable()    ( SSI_CR0 |= SSI_CR0_SSIE )
#define ssi_disable()   ( SSI_CR0 &= ~SSI_CR0_SSIE )
#define ssi_select_ce() ( SSI_CR0 &= ~SSI_CR0_FSEL )

#define ssi_normal_mode() ( SSI_ITR &= ~SSI_ITR_IVLTM_MASK )

static void ssi_select_ce2 ():
	SSI_CR0 |= SSI_CR0_FSEL
	SSI_CR1 &= ~SSI_CR1_MULTS

static void ssi_select_gpc ():
	SSI_CR0 &= ~SSI_CR0_FSEL
	SSI_CR1 |= SSI_CR1_MULTS

#define ssi_enable_tx_intr() 	( SSI_CR0 |= SSI_CR0_TIE | SSI_CR0_TEIE )

#define ssi_disable_tx_intr() ( SSI_CR0 &= ~(SSI_CR0_TIE | SSI_CR0_TEIE) )

#define ssi_enable_rx_intr() 	( SSI_CR0 |= SSI_CR0_RIE | SSI_CR0_REIE )

#define ssi_disable_rx_intr() ( SSI_CR0 &= ~(SSI_CR0_RIE | SSI_CR0_REIE) )

#define ssi_enable_txfifo_half_empty_intr()  ( SSI_CR0 |= SSI_CR0_TIE )
#define ssi_disable_txfifo_half_empty_intr()  ( SSI_CR0 &= ~SSI_CR0_TIE )
#define ssi_enable_tx_error_intr()  ( SSI_CR0 |= SSI_CR0_TEIE )
#define ssi_disable_tx_error_intr()  ( SSI_CR0 &= ~SSI_CR0_TEIE )

#define ssi_enable_rxfifo_half_full_intr()  ( SSI_CR0 |= SSI_CR0_RIE )
#define ssi_disable_rxfifo_half_full_intr()  ( SSI_CR0 &= ~SSI_CR0_RIE )
#define ssi_enable_rx_error_intr()  ( SSI_CR0 |= SSI_CR0_REIE )
#define ssi_disable_rx_error_intr()  ( SSI_CR0 &= ~SSI_CR0_REIE )

#define ssi_enable_loopback()  ( SSI_CR0 |= SSI_CR0_LOOP )
#define ssi_disable_loopback() ( SSI_CR0 &= ~SSI_CR0_LOOP )

#define ssi_enable_receive()   ( SSI_CR0 &= ~SSI_CR0_DISREV )
#define ssi_disable_receive()  ( SSI_CR0 |= SSI_CR0_DISREV )

#define ssi_finish_receive() 	( SSI_CR0 |= (SSI_CR0_RFINE | SSI_CR0_RFINC) )

#define ssi_disable_recvfinish() ( SSI_CR0 &= ~(SSI_CR0_RFINE | SSI_CR0_RFINC) )

#define ssi_flush_txfifo()   ( SSI_CR0 |= SSI_CR0_TFLUSH )
#define ssi_flush_rxfifo()   ( SSI_CR0 |= SSI_CR0_RFLUSH )

#define ssi_flush_fifo() ( SSI_CR0 |= SSI_CR0_TFLUSH | SSI_CR0_RFLUSH )

#define ssi_finish_transmit() ( SSI_CR1 &= ~SSI_CR1_UNFIN )

static void ssi_spi_format():
	SSI_CR1 &= ~SSI_CR1_FMAT_MASK
	SSI_CR1 |= SSI_CR1_FMAT_SPI
	SSI_CR1 &= ~(SSI_CR1_TFVCK_MASK|SSI_CR1_TCKFI_MASK)
	SSI_CR1 |= (SSI_CR1_TFVCK_1 | SSI_CR1_TCKFI_1)

// TI's SSP format, must clear SSI_CR1.UNFIN
static void ssi_ssp_format ():
	SSI_CR1 &= ~(SSI_CR1_FMAT_MASK | SSI_CR1_UNFIN)
	SSI_CR1 |= SSI_CR1_FMAT_SSP

// National's Microwire format, must clear SSI_CR0.RFINE, and set max delay
static void ssi_microwire_format ():
	SSI_CR1 &= ~SSI_CR1_FMAT_MASK
	SSI_CR1 |= SSI_CR1_FMAT_MW1
	SSI_CR1 &= ~(SSI_CR1_TFVCK_MASK|SSI_CR1_TCKFI_MASK)
	SSI_CR1 |= (SSI_CR1_TFVCK_3 | SSI_CR1_TCKFI_3)
	SSI_CR0 &= ~SSI_CR0_RFINE

// CE# level (FRMHL), CE# in interval time (ITFRM), clock phase and polarity (PHA POL), interval time (SSIITR), interval characters/frame (SSIICR)
// frmhl,endian,mcom,flen,pha,pol MASK
#define SSICR1_MISC_MASK 					( SSI_CR1_FRMHL_MASK | SSI_CR1_LFST | SSI_CR1_MCOM_MASK	| SSI_CR1_FLEN_MASK | SSI_CR1_PHA | SSI_CR1_POL )	
static void ssi_spi_set_misc (unsigned frmhl, unsigned endian, unsigned flen, unsigned mcom, unsigned pha, unsigned pol):
	SSI_CR1 &= ~SSICR1_MISC_MASK
	SSI_CR1 |= ((frmhl) << 30) | ((endian) << 25) | (((mcom) - 1) << 12) | (((flen) - 2) << 4) | ((pha) << 1) | (pol)

// Transfer with MSB or LSB first
#define ssi_set_msb() ( SSI_CR1 &= ~SSI_CR1_LFST )
#define ssi_set_lsb() ( SSI_CR1 |= SSI_CR1_LFST )

#define ssi_set_frame_length(n) SSI_CR1 = (SSI_CR1 & ~SSI_CR1_FLEN_MASK) | (((n) - 2) << 4) 

// n = 1 - 16
#define ssi_set_microwire_command_length(n) ( SSI_CR1 = ((SSI_CR1 & ~SSI_CR1_MCOM_MASK) | SSI_CR1_MCOM_##n##BIT) )

// Set the clock phase for SPI
#define ssi_set_spi_clock_phase(n) ( SSI_CR1 = ((SSI_CR1 & ~SSI_CR1_PHA) | ((n&0x1)<< 1)))

// Set the clock polarity for SPI
#define ssi_set_spi_clock_polarity(n) ( SSI_CR1 = ((SSI_CR1 & ~SSI_CR1_POL) | (n&0x1)) )

// n = ix8
#define ssi_set_tx_trigger(n) do { SSI_CR1 &= ~SSI_CR1_TTRG_MASK; SSI_CR1 |= SSI_CR1_TTRG_##n; } while (0)

// n = ix8
#define ssi_set_rx_trigger(n) do { SSI_CR1 &= ~SSI_CR1_RTRG_MASK; SSI_CR1 |= SSI_CR1_RTRG_##n; } while (0)

#define ssi_get_txfifo_count() ( (SSI_SR & SSI_SR_TFIFONUM_MASK) >> SSI_SR_TFIFONUM_BIT )

#define ssi_get_rxfifo_count() ( (SSI_SR & SSI_SR_RFIFONUM_MASK) >> SSI_SR_RFIFONUM_BIT )

#define ssi_clear_errors() ( SSI_SR &= ~(SSI_SR_UNDR | SSI_SR_OVER) )

#define ssi_transfer_end()	( SSI_SR & SSI_SR_END )
#define ssi_is_busy()		( SSI_SR & SSI_SR_BUSY )

#define ssi_txfifo_full()	( SSI_SR & SSI_SR_TFF )
#define ssi_rxfifo_empty()	( SSI_SR & SSI_SR_RFE )
#define ssi_rxfifo_noempty()	( SSI_SR & SSI_SR_RFHF )

#define ssi_set_clk(dev_clk, ssi_clk) ( SSI_GR = (dev_clk) / (2*(ssi_clk)) - 1 )

#define ssi_receive_data()    SSI_DR
#define ssi_transmit_data(v)  ( SSI_DR = (v) )


//**************************************************************************
// CIM
//**************************************************************************

#define cim_enable()	( CIM_CTRL |= CIM_CTRL_ENA )
#define cim_disable()	( CIM_CTRL &= ~CIM_CTRL_ENA )

#define cim_input_data_inverse()	( CIM_CFG |= CIM_CFG_INV_DAT )
#define cim_input_data_normal()	( CIM_CFG &= ~CIM_CFG_INV_DAT )

#define cim_vsync_active_low()	( CIM_CFG |= CIM_CFG_VSP )
#define cim_vsync_active_high()	( CIM_CFG &= ~CIM_CFG_VSP )

#define cim_hsync_active_low()	( CIM_CFG |= CIM_CFG_HSP )
#define cim_hsync_active_high()	( CIM_CFG &= ~CIM_CFG_HSP )

#define cim_sample_data_at_pclk_falling_edge() ( CIM_CFG |= CIM_CFG_PCP )
#define cim_sample_data_at_pclk_rising_edge() ( CIM_CFG &= ~CIM_CFG_PCP )

#define cim_enable_dummy_zero()	( CIM_CFG |= CIM_CFG_DUMMY_ZERO )
#define cim_disable_dummy_zero()	( CIM_CFG &= ~CIM_CFG_DUMMY_ZERO )

#define cim_select_external_vsync()	( CIM_CFG |= CIM_CFG_EXT_VSYNC )
#define cim_select_internal_vsync()	( CIM_CFG &= ~CIM_CFG_EXT_VSYNC )

// n=0-7
#define cim_set_data_packing_mode(n) do { CIM_CFG &= ~CIM_CFG_PACK_MASK; CIM_CFG |= (CIM_CFG_PACK_##n); } while (0)

static void cim_enable_ccir656_progressive_mode ():
    CIM_CFG &= ~CIM_CFG_DSM_MASK
    CIM_CFG |= CIM_CFG_DSM_CPM

static void cim_enable_ccir656_interlace_mode ():
    CIM_CFG &= ~CIM_CFG_DSM_MASK
    CIM_CFG |= CIM_CFG_DSM_CIM

static void cim_enable_gated_clock_mode ():
    CIM_CFG &= ~CIM_CFG_DSM_MASK
    CIM_CFG |= CIM_CFG_DSM_GCM

static void cim_enable_nongated_clock_mode ():
    CIM_CFG &= ~CIM_CFG_DSM_MASK
    CIM_CFG |= CIM_CFG_DSM_NGCM

// sclk:system bus clock
// mclk: CIM master clock
#define cim_set_master_clk(sclk, mclk) do { CIM_CTRL &= ~CIM_CTRL_MCLKDIV_MASK; CIM_CTRL |= (((sclk)/(mclk) - 1) << CIM_CTRL_MCLKDIV_BIT); } while (0)

#define cim_enable_sof_intr() ( CIM_CTRL |= CIM_CTRL_DMA_SOFM )
#define cim_disable_sof_intr() ( CIM_CTRL &= ~CIM_CTRL_DMA_SOFM )

#define cim_enable_eof_intr() ( CIM_CTRL |= CIM_CTRL_DMA_EOFM )
#define cim_disable_eof_intr() ( CIM_CTRL &= ~CIM_CTRL_DMA_EOFM )

#define cim_enable_stop_intr() ( CIM_CTRL |= CIM_CTRL_DMA_STOPM )
#define cim_disable_stop_intr() ( CIM_CTRL &= ~CIM_CTRL_DMA_STOPM )

#define cim_enable_trig_intr() ( CIM_CTRL |= CIM_CTRL_RXF_TRIGM )
#define cim_disable_trig_intr() ( CIM_CTRL &= ~CIM_CTRL_RXF_TRIGM )

#define cim_enable_rxfifo_overflow_intr() ( CIM_CTRL |= CIM_CTRL_RXF_OFM )
#define cim_disable_rxfifo_overflow_intr() ( CIM_CTRL &= ~CIM_CTRL_RXF_OFM )

// n=1-16
#define cim_set_frame_rate(n) do { CIM_CTRL &= ~CIM_CTRL_FRC_MASK; CIM_CTRL |= CIM_CTRL_FRC_##n; } while (0)

#define cim_enable_dma()   ( CIM_CTRL |= CIM_CTRL_DMA_EN )
#define cim_disable_dma()  ( CIM_CTRL &= ~CIM_CTRL_DMA_EN )

#define cim_reset_rxfifo() ( CIM_CTRL |= CIM_CTRL_RXF_RST )
#define cim_unreset_rxfifo() ( CIM_CTRL &= ~CIM_CTRL_RXF_RST )

// n=4,8,12,16,20,24,28,32
#define cim_set_rxfifo_trigger(n) do { CIM_CTRL &= ~CIM_CTRL_RXF_TRIG_MASK; CIM_CTRL |= CIM_CTRL_RXF_TRIG_##n; } while (0)

#define cim_clear_state()   	     ( CIM_STATE = 0 )

#define cim_disable_done()   	     ( CIM_STATE & CIM_STATE_VDD )
#define cim_rxfifo_empty()   	     ( CIM_STATE & CIM_STATE_RXF_EMPTY )
#define cim_rxfifo_reach_trigger() ( CIM_STATE & CIM_STATE_RXF_TRIG )
#define cim_rxfifo_overflow()      ( CIM_STATE & CIM_STATE_RXF_OF )
#define cim_clear_rxfifo_overflow() ( CIM_STATE &= ~CIM_STATE_RXF_OF )
#define cim_dma_stop()   	     ( CIM_STATE & CIM_STATE_DMA_STOP )
#define cim_dma_eof()   	     ( CIM_STATE & CIM_STATE_DMA_EOF )
#define cim_dma_sof()   	     ( CIM_STATE & CIM_STATE_DMA_SOF )

#define cim_get_iid()   	     ( CIM_IID )
#define cim_get_image_data()       ( CIM_RXFIFO )
#define cim_get_dam_cmd()          ( CIM_CMD )

#define cim_set_da(a)              ( CIM_DA = (a) )

//**************************************************************************
// LCD
//**************************************************************************
#define lcd_as_smart_lcd() 		( LCD_CFG |= (1<<LCD_CFG_LCDPIN_BIT) )
#define lcd_as_general_lcd() 		( LCD_CFG &= ~(1<<LCD_CFG_LCDPIN_BIT) )

#define lcd_set_dis()			( LCD_CTRL |= LCD_CTRL_DIS )
#define lcd_clr_dis()			( LCD_CTRL &= ~LCD_CTRL_DIS )

#define lcd_set_ena()			( LCD_CTRL |= LCD_CTRL_ENA )
#define lcd_clr_ena()			( LCD_CTRL &= ~LCD_CTRL_ENA )

// n=1,2,4,8,16
#define lcd_set_bpp(n) ( LCD_CTRL = (LCD_CTRL & ~LCD_CTRL_BPP_MASK) | LCD_CTRL_BPP_##n )

// n=4,8,16
#define lcd_set_burst_length(n) do { LCD_CTRL &= ~LCD_CTRL_BST_MASK; LCD_CTRL |= LCD_CTRL_BST_n##; } while (0)

#define lcd_select_rgb565()		( LCD_CTRL &= ~LCD_CTRL_RGB555 )
#define lcd_select_rgb555()		( LCD_CTRL |= LCD_CTRL_RGB555 )

#define lcd_set_ofup()		( LCD_CTRL |= LCD_CTRL_OFUP )
#define lcd_clr_ofup()		( LCD_CTRL &= ~LCD_CTRL_OFUP )

// n=2,4,16
#define lcd_set_stn_frc(n) do { LCD_CTRL &= ~LCD_CTRL_FRC_MASK; LCD_CTRL |= LCD_CTRL_FRC_n##; } while (0)


#define lcd_pixel_endian_little()	( LCD_CTRL |= LCD_CTRL_PEDN )
#define lcd_pixel_endian_big()	( LCD_CTRL &= ~LCD_CTRL_PEDN )

#define lcd_reverse_byte_endian()	( LCD_CTRL |= LCD_CTRL_BEDN )
#define lcd_normal_byte_endian()	( LCD_CTRL &= ~LCD_CTRL_BEDN )

#define lcd_enable_eof_intr()		( LCD_CTRL |= LCD_CTRL_EOFM )
#define lcd_disable_eof_intr()	( LCD_CTRL &= ~LCD_CTRL_EOFM )

#define lcd_enable_sof_intr()		( LCD_CTRL |= LCD_CTRL_SOFM )
#define lcd_disable_sof_intr()	( LCD_CTRL &= ~LCD_CTRL_SOFM )

#define lcd_enable_ofu_intr()		( LCD_CTRL |= LCD_CTRL_OFUM )
#define lcd_disable_ofu_intr()	( LCD_CTRL &= ~LCD_CTRL_OFUM )

#define lcd_enable_ifu0_intr()	( LCD_CTRL |= LCD_CTRL_IFUM0 )
#define lcd_disable_ifu0_intr()	( LCD_CTRL &= ~LCD_CTRL_IFUM0 )

#define lcd_enable_ifu1_intr()	( LCD_CTRL |= LCD_CTRL_IFUM1 )
#define lcd_disable_ifu1_intr()	( LCD_CTRL &= ~LCD_CTRL_IFUM1 )

#define lcd_enable_ldd_intr()		( LCD_CTRL |= LCD_CTRL_LDDM )
#define lcd_disable_ldd_intr()	( LCD_CTRL &= ~LCD_CTRL_LDDM )

#define lcd_enable_qd_intr()		( LCD_CTRL |= LCD_CTRL_QDM )
#define lcd_disable_qd_intr()		( LCD_CTRL &= ~LCD_CTRL_QDM )


// LCD status register indication

#define lcd_quick_disable_done()	( LCD_STATE & LCD_STATE_QD )
#define lcd_disable_done()		( LCD_STATE & LCD_STATE_LDD )
#define lcd_infifo0_underrun()	( LCD_STATE & LCD_STATE_IFU0 )
#define lcd_infifo1_underrun()	( LCD_STATE & LCD_STATE_IFU1 )
#define lcd_outfifo_underrun()	( LCD_STATE & LCD_STATE_OFU )
#define lcd_start_of_frame()		( LCD_STATE & LCD_STATE_SOF )
#define lcd_end_of_frame()		( LCD_STATE & LCD_STATE_EOF )

#define lcd_clr_outfifounderrun()	( LCD_STATE &= ~LCD_STATE_OFU )
#define lcd_clr_sof()			( LCD_STATE &= ~LCD_STATE_SOF )
#define lcd_clr_eof()			( LCD_STATE &= ~LCD_STATE_EOF )

#define lcd_panel_white()		( LCD_CFG |= LCD_CFG_WHITE )
#define lcd_panel_black()		( LCD_CFG &= ~LCD_CFG_WHITE )

// n=1,2,4,8 for single mono-STN 
// n=4,8 for dual mono-STN
#define lcd_set_panel_datawidth(n) do { LCD_CFG &= ~LCD_CFG_PDW_MASK; LCD_CFG |= LCD_CFG_PDW_n##; } while (0)

// m=LCD_CFG_MODE_GENERUIC_TFT_xxx
#define lcd_set_panel_mode(m) do { LCD_CFG &= ~LCD_CFG_MODE_MASK; LCD_CFG |= (m); } while(0)

// n = 0-255
#define lcd_disable_ac_bias()		( LCD_IO = 0xff )
#define lcd_set_ac_bias(n) do { LCD_IO &= ~LCD_IO_ACB_MASK; LCD_IO |= ((n) << LCD_IO_ACB_BIT); } while(0)

#define lcd_io_set_dir()		( LCD_IO |= LCD_IO_DIR )
#define lcd_io_clr_dir()		( LCD_IO &= ~LCD_IO_DIR )

#define lcd_io_set_dep()		( LCD_IO |= LCD_IO_DEP )
#define lcd_io_clr_dep()		( LCD_IO &= ~LCD_IO_DEP )

#define lcd_io_set_vsp()		( LCD_IO |= LCD_IO_VSP )
#define lcd_io_clr_vsp()		( LCD_IO &= ~LCD_IO_VSP )

#define lcd_io_set_hsp()		( LCD_IO |= LCD_IO_HSP )
#define lcd_io_clr_hsp()		( LCD_IO &= ~LCD_IO_HSP )

#define lcd_io_set_pcp()		( LCD_IO |= LCD_IO_PCP )
#define lcd_io_clr_pcp()		( LCD_IO &= ~LCD_IO_PCP )

#define lcd_vsync_get_vps() ( (LCD_VSYNC & LCD_VSYNC_VPS_MASK) >> LCD_VSYNC_VPS_BIT )

#define lcd_vsync_get_vpe() ( (LCD_VSYNC & LCD_VSYNC_VPE_MASK) >> LCD_VSYNC_VPE_BIT )
#define lcd_vsync_set_vpe(n) do { LCD_VSYNC &= ~LCD_VSYNC_VPE_MASK; LCD_VSYNC |= (n) << LCD_VSYNC_VPE_BIT; } while (0)

#define lcd_hsync_get_hps() ( (LCD_HSYNC & LCD_HSYNC_HPS_MASK) >> LCD_HSYNC_HPS_BIT )
#define lcd_hsync_set_hps(n) do { LCD_HSYNC &= ~LCD_HSYNC_HPS_MASK; LCD_HSYNC |= (n) << LCD_HSYNC_HPS_BIT; } while (0)

#define lcd_hsync_get_hpe() ( (LCD_HSYNC & LCD_HSYNC_HPE_MASK) >> LCD_VSYNC_HPE_BIT )
#define lcd_hsync_set_hpe(n) do { LCD_HSYNC &= ~LCD_HSYNC_HPE_MASK; LCD_HSYNC |= (n) << LCD_HSYNC_HPE_BIT; } while (0)

#define lcd_vat_get_ht() ( (LCD_VAT & LCD_VAT_HT_MASK) >> LCD_VAT_HT_BIT )
#define lcd_vat_set_ht(n) do { LCD_VAT &= ~LCD_VAT_HT_MASK; LCD_VAT |= (n) << LCD_VAT_HT_BIT; } while (0)

#define lcd_vat_get_vt() ( (LCD_VAT & LCD_VAT_VT_MASK) >> LCD_VAT_VT_BIT )
#define lcd_vat_set_vt(n) do { LCD_VAT &= ~LCD_VAT_VT_MASK; LCD_VAT |= (n) << LCD_VAT_VT_BIT; } while (0)

#define lcd_dah_get_hds() ( (LCD_DAH & LCD_DAH_HDS_MASK) >> LCD_DAH_HDS_BIT )
#define lcd_dah_set_hds(n) do { LCD_DAH &= ~LCD_DAH_HDS_MASK; LCD_DAH |= (n) << LCD_DAH_HDS_BIT; } while (0)

#define lcd_dah_get_hde() ( (LCD_DAH & LCD_DAH_HDE_MASK) >> LCD_DAH_HDE_BIT )
#define lcd_dah_set_hde(n) do { LCD_DAH &= ~LCD_DAH_HDE_MASK; LCD_DAH |= (n) << LCD_DAH_HDE_BIT; } while (0)

#define lcd_dav_get_vds() ( (LCD_DAV & LCD_DAV_VDS_MASK) >> LCD_DAV_VDS_BIT )
#define lcd_dav_set_vds(n) do { LCD_DAV &= ~LCD_DAV_VDS_MASK; LCD_DAV |= (n) << LCD_DAV_VDS_BIT; } while (0)

#define lcd_dav_get_vde() ( (LCD_DAV & LCD_DAV_VDE_MASK) >> LCD_DAV_VDE_BIT )
#define lcd_dav_set_vde(n) do { LCD_DAV &= ~LCD_DAV_VDE_MASK; LCD_DAV |= (n) << LCD_DAV_VDE_BIT; } while (0)

#define lcd_cmd0_set_sofint()		( LCD_CMD0 |= LCD_CMD_SOFINT )
#define lcd_cmd0_clr_sofint()		( LCD_CMD0 &= ~LCD_CMD_SOFINT )
#define lcd_cmd1_set_sofint()		( LCD_CMD1 |= LCD_CMD_SOFINT )
#define lcd_cmd1_clr_sofint()		( LCD_CMD1 &= ~LCD_CMD_SOFINT )

#define lcd_cmd0_set_eofint()		( LCD_CMD0 |= LCD_CMD_EOFINT )
#define lcd_cmd0_clr_eofint()		( LCD_CMD0 &= ~LCD_CMD_EOFINT )
#define lcd_cmd1_set_eofint()		( LCD_CMD1 |= LCD_CMD_EOFINT )
#define lcd_cmd1_clr_eofint()		( LCD_CMD1 &= ~LCD_CMD_EOFINT )

#define lcd_cmd0_set_pal()		( LCD_CMD0 |= LCD_CMD_PAL )
#define lcd_cmd0_clr_pal()		( LCD_CMD0 &= ~LCD_CMD_PAL )

#define lcd_cmd0_get_len() ( (LCD_CMD0 & LCD_CMD_LEN_MASK) >> LCD_CMD_LEN_BIT )
#define lcd_cmd1_get_len() ( (LCD_CMD1 & LCD_CMD_LEN_MASK) >> LCD_CMD_LEN_BIT )

//**************************************************************************
// RTC ops
//**************************************************************************

#define rtc_write_ready()  ( (RTC_RCR & RTC_RCR_WRDY) >> RTC_RCR_WRDY_BIT )
#define rtc_enabled()        ( RTC_RCR |= RTC_RCR_RTCE )
#define rtc_disabled()         ( RTC_RCR &= ~RTC_RCR_RTCE )
#define rtc_enable_alarm()         ( RTC_RCR |= RTC_RCR_AE )
#define rtc_disable_alarm()         ( RTC_RCR &= ~RTC_RCR_AE )
#define rtc_alarm_is_enabled()         ( RTC_RCR & RTC_RCR_AE )
#define rtc_enable_alarm_irq()         ( RTC_RCR |= RTC_RCR_AIE )
#define rtc_disable_alarm_irq()         ( RTC_RCR &= ~RTC_RCR_AIE )
#define rtc_enable_1Hz_irq()         ( RTC_RCR |= RTC_RCR_1HZIE )
#define rtc_disable_1Hz_irq()         ( RTC_RCR &= ~RTC_RCR_1HZIE )

#define rtc_get_1Hz_flag()           ( (RTC_RCR >> RTC_RCR_1HZ_BIT) & 0x1 )
#define rtc_clear_1Hz_flag()           ( RTC_RCR &= ~RTC_RCR_1HZ )
#define rtc_get_alarm_flag()           ( (RTC_RCR >> RTC_RCR_AF_BIT) & 0x1 )
#define rtc_clear_alarm_flag()           ( RTC_RCR &= ~RTC_RCR_AF )

#define rtc_get_second()   ( RTC_RSR )
#define rtc_set_second(v)   ( RTC_RSR = v )

#define rtc_get_alarm_second()   ( RTC_RSAR )
#define rtc_set_alarm_second(v)   ( RTC_RSAR = v )

#define rtc_RGR_is_locked()       ( (RTC_RGR >> RTC_RGR_LOCK) )
#define rtc_lock_RGR()       ( RTC_RGR |= RTC_RGR_LOCK )
#define rtc_unlock_RGR()       ( RTC_RGR &= ~RTC_RGR_LOCK )
#define rtc_get_adjc_val()       ( (RTC_RGR & RTC_RGR_ADJC_MASK) >> RTC_RGR_ADJC_BIT )
#define rtc_set_adjc_val(v)      ( RTC_RGR = ( (RTC_RGR & ~RTC_RGR_ADJC_MASK) | (v << RTC_RGR_ADJC_BIT) ))
#define rtc_get_nc1Hz_val()       ( (RTC_RGR & RTC_RGR_NC1HZ_MASK) >> RTC_RGR_NC1HZ_BIT )
#define rtc_set_nc1Hz_val(v)      ( RTC_RGR = ( (RTC_RGR & ~RTC_RGR_NC1HZ_MASK) | (v << RTC_RGR_NC1HZ_BIT) ))

#define rtc_power_down()            ( RTC_HCR |= RTC_HCR_PD )

#define rtc_get_hwfcr_val()         ( RTC_HWFCR & RTC_HWFCR_MASK )
#define rtc_set_hwfcr_val(v)         ( RTC_HWFCR = (v) & RTC_HWFCR_MASK )
#define rtc_get_hrcr_val()         ( RTC_HRCR & RTC_HRCR_MASK )
#define rtc_set_hrcr_val(v)         ( RTC_HRCR = (v) & RTC_HRCR_MASK )

#define rtc_enable_alarm_wakeup()        ( RTC_HWCR |= RTC_HWCR_EALM )
#define rtc_disable_alarm_wakeup()        ( RTC_HWCR &= ~RTC_HWCR_EALM )

#define rtc_status_hib_reset_occur()        ( (RTC_HWRSR >> RTC_HWRSR_HR) & 0x1 )
#define rtc_status_ppr_reset_occur()        ( (RTC_HWRSR >> RTC_HWRSR_PPR) & 0x1 )
#define rtc_status_wakeup_pin_waken_up()    ( (RTC_HWRSR >> RTC_HWRSR_PIN) & 0x1 )
#define rtc_status_alarm_waken_up()        ( (RTC_HWRSR >> RTC_HWRSR_ALM) & 0x1 )
#define rtc_clear_hib_stat_all()               ( RTC_HWRSR = 0 )

#define rtc_get_scratch_pattern() 		(RTC_HSPR)
#define rtc_set_scratch_pattern(n) 		(RTC_HSPR = n )


#ifdef __KERNEL__
static void setup_sdram ():
	// SDRAM BANK Number: 1, 2
	unsigned CONFIG_NR_DRAM_BANKS = 1
	// CAS latency: 2 or 3
	unsigned SDRAM_CASL = 2
	// SDRAM Timings, unit: ns
	// RAS# Active Time
	unsigned SDRAM_TRAS = 45
	// RAS# to CAS# Delay
	unsigned SDRAM_RCD = 20
	// RAS# Precharge Time
	unsigned SDRAM_TPC = 20
	// Write Latency Time
	unsigned SDRAM_TRWL = 7
	// Refresh period: 4096 refresh cycles/64ms
	unsigned SDRAM_TREF = 7812
	unsigned dmcr0, dmcr, sdmode, tmp, cpu_clk, mem_clk, ns
	unsigned cas_latency_sdmr[2] = { EMC_SDMR_CAS_2, EMC_SDMR_CAS_3 }
	unsigned cas_latency_dmcr[2] = { 1 << EMC_DMCR_TCL_BIT, 2 << EMC_DMCR_TCL_BIT }
	int div[] = {1, 2, 3, 4, 6, 8, 12, 16, 24, 32}

	cpu_clk = 252000000
	gpio_as_sdram_16bit ()
	unsigned SDRAM_BW16 = 0
	unsigned SDRAM_BANK4 = 1
	unsigned SDRAM_ROW = 12
	unsigned SDRAM_COL = 8

	mem_clk = cpu_clk * div[cpm_get_cdiv()] / div[cpm_get_mdiv()]
	EMC_BCR = 0
	EMC_RTCSR = 0
	unsigned SDRAM_ROW0 = 11
	unsigned SDRAM_COL0 = 8
	unsigned SDRAM_BANK40 = 0
	dmcr0 = ((SDRAM_ROW0-11)<<EMC_DMCR_RA_BIT) | ((SDRAM_COL0-8)<<EMC_DMCR_CA_BIT) | (SDRAM_BANK40<<EMC_DMCR_BA_BIT) | (SDRAM_BW16<<EMC_DMCR_BW_BIT) | EMC_DMCR_EPIN | cas_latency_dmcr[((SDRAM_CASL == 3) ? 1 : 0)]
	// Basic DMCR value
	dmcr = ((SDRAM_ROW-11)<<EMC_DMCR_RA_BIT) | ((SDRAM_COL-8)<<EMC_DMCR_CA_BIT) | (SDRAM_BANK4<<EMC_DMCR_BA_BIT) | (SDRAM_BW16<<EMC_DMCR_BW_BIT) | EMC_DMCR_EPIN | cas_latency_dmcr[((SDRAM_CASL == 3) ? 1 : 0)]
	// SDRAM timimg
	ns = 1000000000 / mem_clk
	tmp = SDRAM_TRAS / ns
	if tmp < 4:
		tmp = 4
	if tmp > 11:
		tmp = 11
	dmcr |= ((tmp-4) << EMC_DMCR_TRAS_BIT)
	tmp = SDRAM_RCD/ns
	if tmp > 3:
		tmp = 3
	dmcr |= (tmp << EMC_DMCR_RCD_BIT)
	tmp = SDRAM_TPC/ns
	if tmp > 7:
		tmp = 7
	dmcr |= (tmp << EMC_DMCR_TPC_BIT)
	tmp = SDRAM_TRWL/ns
	if tmp > 3:
		tmp = 3
	dmcr |= (tmp << EMC_DMCR_TRWL_BIT)
	tmp = (SDRAM_TRAS + SDRAM_TPC)/ns
	if tmp > 14:
		tmp = 14
	dmcr |= (((tmp + 1) >> 1) << EMC_DMCR_TRC_BIT)

	// SDRAM mode value
	sdmode = EMC_SDMR_BT_SEQ | EMC_SDMR_OM_NORMAL | EMC_SDMR_BL_4 | cas_latency_sdmr[((SDRAM_CASL == 3) ? 1 : 0)];

	// Stage 1. Precharge all banks by writing SDMR with DMCR.MRSET=0
	EMC_DMCR = dmcr
	REG8(EMC_SDMR0|sdmode) = 0

	// Wait for precharge, > 200us
	tmp = (cpu_clk / 1000000) * 1000
	volatile unsigned t = tmp
	while t--:

	// Stage 2. Enable auto-refresh
	EMC_DMCR = dmcr | EMC_DMCR_RFSH

	tmp = SDRAM_TREF/ns
	tmp = tmp/64 + 1
	if tmp > 0xff:
		tmp = 0xff
	EMC_RTCOR = tmp
	EMC_RTCNT = 0
	// Divisor is 64, CKO/64
	EMC_RTCSR = EMC_RTCSR_CKS_64

	// Wait for number of auto-refresh cycles
	tmp = (cpu_clk / 1000000) * 1000
	t = tmp
	while t--:

	// Stage 3. Mode Register Set
	EMC_DMCR = dmcr0 | EMC_DMCR_RFSH | EMC_DMCR_MRSET
	REG8(EMC_SDMR0|sdmode) = 0

	// Set back to basic DMCR value
	EMC_DMCR = dmcr | EMC_DMCR_RFSH | EMC_DMCR_MRSET
	#if 0
	EMC_SMCR (0) = 0x00000080
	EMC_SMCR (1) = 0x094c4400
	EMC_SMCR (2) = 0x0fff7700
	EMC_SMCR (3) = 0x0fff7700
	EMC_SMCR (4) = 0x0fff7700
	EMC_SACR (0) = 0x1cfc
	EMC_SACR (1) = 0x18fc
	EMC_SACR (2) = 0x14fc
	EMC_SACR (3) = 0x0cfc
	EMC_SACR (4) = 0x08fc
	EMC_DMCR = 0x85aa3211
	EMC_RTCSR = 0x83
	EMC_RTCOR = 0x1f
	#endif
	#if 0
	for unsigned i = 0; i < 5; ++i:
		dbg_log ("memory: ")
		dbg_log_num (EMC_SMCR (i), 8)
		dbg_log (",")
		dbg_log_num (EMC_SACR (i), 8)
		dbg_log (";")
	dbg_log_num (EMC_RTCSR, 8)
	dbg_log (",")
	dbg_log_num (EMC_RTCOR, 8)
	dbg_log ("\n")
	#endif

static void setup_uart ():
	#ifndef NDEBUG
	// Set up uart.
	cpm_start_uart0 ()
	gpio_as_uart0 ()
	UART0_IER = 0
	UART0_FCR = 0
	UART0_MCR = 0
	UART0_SIRCR = 0
	UART0_UACR = 0
	UART0_UMR = 16
	UART0_LCR = UARTLCR_WLEN_8 | UARTLCR_STOP1 | UARTLCR_DLAB
	unsigned const baud = 57600
	unsigned uart_div = 12000000 / 16 / baud
	UART0_DLHR = (uart_div >> 8) & 0xff
	UART0_DLLR = uart_div & 0xff
	UART0_LCR = UARTLCR_WLEN_8 | UARTLCR_STOP1
	UART0_FCR = UARTFCR_UUE | UARTFCR_FE | UARTFCR_RFLS | UARTFCR_TFLS
	#endif
#endif

#endif