juhosg
b33cedf6fa
ar71xx: add ethernet initialization for the AR933X SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27063 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:37 +00:00
juhosg
aa6b4cd97a
ar71xx: enable USB support for the AR933x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27062 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:36 +00:00
juhosg
6f45adddfe
ar71xx: add AR933x specific glue for ar71xx_device{start,stop}
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27061 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:35 +00:00
juhosg
c7eb38661b
ar71xx: the watchdog uses the reference clock on the AR933x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27060 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:34 +00:00
juhosg
0570263dcb
ar71xx: add AR933x specific glue code for IRQ initialization
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27059 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:32 +00:00
juhosg
771bbc30cf
ar71xx: don't register 8250 UART on the AR933x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27058 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:31 +00:00
juhosg
4cae90b75b
ar71xx: enable GPIO support for the AR933x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27057 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:30 +00:00
juhosg
046f6d9c97
ar71xx: add AR933x specific frequency initialization code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27056 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:29 +00:00
juhosg
9d012c4aae
ar71xx: add AR933x specific early_printk support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27055 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:27 +00:00
juhosg
a5e8c5446f
ar71xx: add preliminary support for the Atheros AR933x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27054 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:26 +00:00
juhosg
eaa759a8e5
ar71xx: Fix header offset for newer WRT160NL models
...
Newer WRT160NLs have a flash chip with 4K erase blocks instead of 64K,
resulting in miscalculated partition sizes.
Since the actual sizes did not change, hardcode them to their current
sizes, and make sure they are at least one erase block big (in case Cisco
decides to start to use chips with 128K erase blocks).
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27049 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:20 +00:00
juhosg
5b9155beba
ar71xx: add SOC_AR{71XX,724X,913X,934X} config symbols
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27048 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:19 +00:00
juhosg
bd8a2aaee9
ar71xx: initialize is_clk_25mhz field for AR9340 WMAC
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27045 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:15 +00:00
juhosg
c772123439
ar71xx: sync ath9k_platform_data.h with compat-wireless
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:14 +00:00
juhosg
75e1476cce
ar71xx: ag71xx: make ring sizes configurable via ethtool
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27041 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:10 +00:00
juhosg
a137dec884
ar71xx: ag71xx: prepare to make ring sizes configurable
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27040 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:09 +00:00
juhosg
940317dc35
ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define
...
Reported-by: Dave Täht <dave.taht@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27039 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-31 22:53:07 +00:00
nbd
debcf79f90
ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo)
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27035 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-30 23:08:01 +00:00
nbd
20aef6d6fc
ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27034 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-30 23:07:57 +00:00
matteo
005a65e01d
ar71xx: don't probe the LAN PHY
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26924 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-17 11:15:24 +00:00
matteo
483991c363
ar71xx: detect link on LAN ports
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26922 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-17 11:12:56 +00:00
matteo
511dea0dac
ar71xx: add link detection on Ubiquiti devices WAN port
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26891 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-14 23:31:50 +00:00
matteo
51053e7640
use correct macros and frame size in ag71xx
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26890 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-14 23:10:06 +00:00
matteo
0cbd6d9057
ar71xx: cosmetic fixes
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26889 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-14 23:08:00 +00:00
juhosg
b500b67652
ar71xx: populate LED3 on the JA76PF board
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26862 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-08 21:38:51 +00:00
juhosg
5b6a159d03
ar71xx: remove superfluous fifo_cfg overrides
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26859 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-08 21:38:46 +00:00
juhosg
bb14a2f07c
ar71xx: ag71xx: make switch register access atomic
...
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.
This is easily noticable during an iperf session:
...
[ 3] 52.0-53.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 53.0-54.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[ 3] 54.0-55.0 sec 6.75 MBytes 56.6 Mbits/sec
[ 3] 55.0-56.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 56.0-57.0 sec 10.5 MBytes 88.1 Mbits/sec
...
[ 3] 169.0-170.0 sec 11.4 MBytes 95.4 Mbits/sec
[ 3] 170.0-171.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[ 3] 171.0-172.0 sec 7.63 MBytes 64.0 Mbits/sec
[ 3] 172.0-173.0 sec 9.38 MBytes 78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[ 3] 173.0-174.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 174.0-175.0 sec 11.4 MBytes 95.4 Mbits/sec
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26856 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-08 16:32:53 +00:00
juhosg
0511a7adf1
ar71xx: ag71xx: fix section mismatch warnings
...
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26855 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-08 13:30:36 +00:00
juhosg
14088891b0
ar71xx: ag71xx: fix build error if debugfs is enabled
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26854 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-08 13:30:26 +00:00
juhosg
e5061b1935
ar71xx: ag71xx: add debugfs entry for [rt]x_ring
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26845 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-07 12:40:34 +00:00
juhosg
5155342ee7
ar71xx: ag71xx: add timestamps to ag71xx_buf
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26844 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-07 12:40:28 +00:00
juhosg
5e10b16d95
ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26843 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-07 12:40:26 +00:00
juhosg
f6816e49d9
ar71xx: ag71xx: use debugfs_remove_recursive
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26842 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-07 12:40:25 +00:00
juhosg
193e04ebee
ar71xx: override wmac device name for the AR934x SoCs
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26840 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-07 09:23:32 +00:00
nbd
118a9c5154
ar71xx: use the ar8316 switch driver on the PB92 board and add a matching default network config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26779 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-28 21:27:42 +00:00
nbd
8220523bad
ar71xx: fix MDIO access on ar7242 (based on a patch by Jess Zhu)
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26777 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-28 19:30:49 +00:00
juhosg
b5cfb56ed4
ar71xx: fix build error w/o CONFIG_PCI
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26606 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-12 13:14:56 +00:00
juhosg
ec1dcc5bda
ar71xx: use the gpio_keys_polled driver instead of gpio_buttons
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26603 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-12 09:29:21 +00:00
juhosg
b47906964d
ar71xx: Add support for WZR-HP-G301NH
...
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26601 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-12 09:29:10 +00:00
juhosg
2be7aaf5c2
ar71xx: merge dev-ar9{13,34}x-wmac into dev-ar9xxx-wmac
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26595 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-11 17:37:08 +00:00
juhosg
613a88e6a5
ar71xx: fix AR934X_WMAC_SIZE
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26594 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-11 17:37:03 +00:00
juhosg
9330419fa7
ar71xx: fix section mismatch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26562 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-09 18:47:55 +00:00
juhosg
f2a69b10a8
ar71xx: rename ar934x_ref_freq to ar71xx_ref_freq
...
Also initialize that for each SoC and print its value along with the
other frequencies.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26561 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-09 18:47:52 +00:00
juhosg
f4bb6b6582
ar71xx: show the SoC type earlier
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26560 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-09 18:47:50 +00:00
juhosg
8de3a1a306
ar71xx: cleanup SoC detection code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26559 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-09 18:47:49 +00:00
juhosg
db38ac7711
ar71xx: Fix mac address offset for AR934x
...
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26557 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-09 18:47:42 +00:00
juhosg
b1f3482e70
ar71xx: add DB120 board specific PCI initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26523 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-07 20:53:41 +00:00
juhosg
004690a661
ar71xx: register WMAC device on the DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26522 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-07 20:53:37 +00:00
juhosg
ce9abcca4a
ar71xx: add support for the built-in WMAC of the AR934x
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26521 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-07 20:53:34 +00:00
juhosg
e018221576
ar71xx: add initial support for the Atheros DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26518 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-07 20:53:19 +00:00