ssb_pcicore_fix_sprom_core_index accesses the sprom on the pci bus but
this causes a data bus error (oops) on a SoC.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27758 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now we can assume that every brcm47xx kernel has the bcma module build
into the kernel. This is not needed for this version as this does not
support bcma as system bus but kernel 3.0 will.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27733 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add new patches for bcm4716 SoC
* add support for serial flash on bcma bus
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27723 3c298f89-4303-0410-b956-a3cf2f4a3e73
The image will not boot because serial flash support is missing this is only for experts.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27302 3c298f89-4303-0410-b956-a3cf2f4a3e73
Ethernet and wifi are not working and this is highly experimental.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27301 3c298f89-4303-0410-b956-a3cf2f4a3e73
2.4 isn't present anymore, so it will always be 2.6 (or newer). Since the
2.6 check will break with 3.0, remove it alltogether.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27185 3c298f89-4303-0410-b956-a3cf2f4a3e73
The flash driver code should be cleaned up and the broad detection code should be placed into arch code and used here.
This fixes#9323
Thank you Will Holmes for the patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27005 3c298f89-4303-0410-b956-a3cf2f4a3e73
If there is no sprom on an ssb based pci device on the brcm47xx
architecture ssb now asks the architecture code to look into the nvram
to get some sprom data for this device. Now we are able to read out
pci/1/1/ foo or pci/1/3/ foo config options.
This will fix some problems where the wireless devices does not got an
mac address and the following message was show:
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26801 3c298f89-4303-0410-b956-a3cf2f4a3e73
This package creates some error messages on startup
Thank you russell-- for reporting
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26240 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Netgear wgt634u uses minus between the hex digest of the mac
address and all other broadcom devices are using colons between the hex
digest. Now the mac address is correctly parsed also when minus is used.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24749 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes a problem with wrt350n.
It boots only if this config option is set, otherwise it reboots after "Switching to clocksource MIPS"
Thank you sn9 for fixing this problem.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24626 3c298f89-4303-0410-b956-a3cf2f4a3e73
Broadcom removed these pci id, but at least the wrt350n has a Ethernet
controller with a pci id of 14e4:1676
Thank you sn9 for fixing this problem.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24625 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport patches from r24162
brcm47xx: reorder patches like they were commitet upstream
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24266 3c298f89-4303-0410-b956-a3cf2f4a3e73
