Note that the PHY is still half-duplex, but we don't need to insist
on the entire packet reception/transmission to finish before letting
the peer have its say.
- dirtpan.c (open_tun): if a command is given, set the environment
variable ITF to the interface name and system(3) the command
- dirtpan.c (usage, main): accept an interface configuration command as
the 4th command-line argument
Note that we still waste at least one perfectly good frame. However,
instead of implementing some fancy arbitration, it's better if we
just make the whole thing bidirectional in the future.
The IEEE 802.15.4 kernel stack doesn't implement ACKs yet and prints
a warning if we request them. Since dirtpan has its own ACKs, we
just disable IEEE 802.15.4 ACKs for now.
- dirtpan.c (debug_ip): only dump local packets if debug > 1
- dirtpan.c (debug_dirt): dump packet content only if debug > 1
- dirtpan.c (debug_dirt): made packet content dump more readable
- dirtpan.c (debug_dirt): added terse debug output for debug == 1
- dirtpan.c (usage): doubling -d now has a meaning
- usbwait.c (need_removal, wait_for_usb): if need_removal is set, wait
for the device to be removed before trying to find it
- usbwait.c (usage, main): new option -r to set need_removal
- usbwait/usbwait.c: update the USB device tree until the specified
device is detected
- usbwait/Makefile: build usbwait (host only)
- Makefile (DIRS, BEN_DIRS, upload): separated subdirectories with tools
that can run on the Ben from those that can't
- Makefile (DIRS): added usbwait/
- usbopen.c (open_usb): determine vendor and product objective outside
the loop
- usbopen.c (open_usb): check vendor and product only if non-zero
- usbopen.c (bad_id, parse_usb_id): vendor and product can now be
omitted
- tools/include/usbopen.h (usb_rescan), tools/lib/usbopen.c (initialized,
initialize, usb_rescan): usb_rescan forces a re-initialization of
libusb and a new scan of the USB device tree
- include/atrf.h (atrf_driver_spec), lib/atrf.c (atrf_driver_spec):
new function to retrieve the local or remote/final driver spec
- lib/atrf.c (struct atrf_dsc, atrf_open, atrf_close): record the local
driver spec
- lib/driver.h (struct atrf_driver): new driver function "driver_spec"
to retrieve the driver spec
- lib/atnet.c (struct atnet_dsc, atnet_open, atnet_close): maintain a
cache for the driver spec
- lib/atnet.c (atnet_driver_spec, atnet_driver): added support for the
"driver_spec" function
- atrf-proxy/PROTOCOL, atrf-proxy/atrf-proxy.c (cmd_zero): added command
SPEC to retrieve the (final) driver spec
- atrf-id/atrf-id.c (usage, main): added option -s to retrieve the
driver spec. One -s retrieves the local spec, -s -s the remote/final.
- Makefile (DIRS): added atrf-xmit
- atrf-xmit/Makefile, atrf-xmit/atrf-xmit.c: new utility atrf-xmit to
rapidly send packets from one device to another and analyze the outcome
- gui.c (disc, indicate): moved drawing of disc to separate function
- gui.c (triangle, up, down): draw an up/down triangle
- gui.c (indicate): use up/down triangle for over/under
- atrf-path.c (do_sweeps): return a pass/fail/undecided value
- gui.h (gui), gui.c (gui): return a pass/fail/undecided value
- gui.c (gui): return pass/fail when P or F is pressed; exit
unconditionally if Q is pressed
- atrf-path.c (main): according to the decision of "gui" or "do_sweeps",
print "#PASS", "#FAIL", or nothing
- gui.c (avg2y, segment): moved mapping from measurement to y position
to separate function, to allow for sharing
- gui.c (LIMIT_RGBA, draw_limit, gui): draw the limits
- sweep.h (MIN_DIFF, MAX_DIFF, struct sweep): added min/max profile
- sweep.h (do_sweep), atrf-path.c (do_half_sweep, do_sweep): compare
result against limits and return pass/fail decision
- sweep.h (N_CHAN), atrf-path.c (do_half_sweep, do_sweeps), gui.c
(N_CHAN): declare number of channels in one central place instead of
scattering it all around the program
- atrf-path.c (do_read_profile, read_profile, usage, main): new option -P
to read a min/max profile
- gui.c (indicate, main): moved indicator to separate function and
improved blink logic
- gui.c (OVER_RGBA, UNDER_RGBA, indicate, main): change color to indicate
pass/fail
atrf-path -T +0.5 -g ... 10 10 time:
before: 0.32-0.33 s
after: 0.27-0.29 s (88%)
- atrf-path.c (sample): force cw test setup if never done before
- atrf-path.c (do_half_sweep): only request cw test setup if sweeping
both offsets
atrf-path -T +0.5 -g ... 10 10 time:
before (both offsets) 0.65 s
after (one offset) 0.32-0.33 s (50%)
- atrf-path.c (usage, main): new option -T to specify which offset to
sweep (default: sweep both)
- atrf-path.c (do_half_sweep): only sample points with the desired offset
- atrf-path.c (print_sweep): only prints points we've sweeped
- gui.c (segment, draw): inverted flag logic from "have_last" to "first"
- gui.c (draw): only plot points we've sweeped
- gui.c (gui): pass the offset selection to "draw"
atrf-path -g ... 10 10 time:
before 1.92 s
after 0.65 s (34%)
- atrf-path.c (do_sweep): separate -0.5 MHz and +0.5 MHz sweep
- atrf-path.c (sample, do_sweep): set up cw test mode only twice per
sweep (once for each offset), and simply resume in all other cases
atrf-path -g ... 10 10 time is now stable at 1.92 s
- atrf-path.c (sample): commented-out init sequence needed for AT86RF230
- atrf-path.c (sample, do_sweep): set TX channel only once per +/-0.5 MHz
pair
- atrf-path.c (sample, do_sweep): "sample" no longer needs the channel
argument
- atrf-path.c (sample, main): do TX init only once
- lib/cwtest.c (enter_test_mode_231, prepare_test_mode_231,
start_test_mode_231, cw_test_begin): broke enter_test_mode_231 into
a slow setup component and a fast start/resume component
- include/cwtest.h (cw_test_resume), lib/cwtest.c (cw_test_resume):
resume transmission in a previously set up test mode
atrf-path -g ... 10 10 time:
before 2.08 s
after 1.92-1.93 s (92-93%)
- atrf-path.c (set_channel, init_common): moved setting of the channel
to separate function, for better granularity
- atrf-path.c (init_common, init_tx, init_rx, sample, do_sweep): the
init_* functions no longer set the channel; use set_channel
- atrf-path.c (main): initialize the receiver only once
- atrf-path.c (usage, main): new option -g to invoke the GUI
- atrf-path.c (usage, main): in GUI mode, the number of sweeps is optional
(default: infinite)
- atrf-path.c (main), gui.h (gui), gui.c (gui): exit after the specified
number of sweeps
The transceiver reset takes quite a while. It seems that also going into
sleep mode has the effect of stopping cw test mode and it's much faster.
This has only been tried on the AT86RF231. For AT86RF230, we therefore
still use the reset.
Performance improvement:
Measurement: atrf-path sweep time in GUI mode, averaging over 10 samples.
Running on PC with remote ATBEN transceivers.
before 7.36-7.68 s
after 2.08 s (27-28% of previous time)
- gui.h, gui.c: plot sweep results with SDL_gfx
- Makefile: added target-specific variables for SDL and SDL_gfx
- atrf-path.c (main): invoke the GUI if the number of sweeps is zero
- sweep.h (struct sweep ), atrf-path.c (sample, do_sweeps, main): pass
sweep parameters via a struct
- sweep.h (do_sweep), atrf-path.c (do_sweep, do_sweeps): separated single
sweep and made it public
- sweep.h (struct sample), atrf-path.c (sample, print_sweep, do_sweeps):
made "sample" and do_sweep return the sample value/vector and moved
output from "sample" to print_sweep
- atrf-path.c (rssi_to_dBm, sample): moved RSSI value to dBm conversion to
separate function
- atrf-path.c (sample): corrected calculation of average
- atrf-path.c (sample): also output minimum and maximum value
- plot: new option -e to display extremal values
- plot: added comment to explain y range
- lib/misctxrx.c (tx_pwr_230, tx_pwr_231): declare tables as "const"
- lib/misctxrx.c (POWER_TABLE_SIZE, set_power_dBm): don't open-code the
table size calculation
- lib/misctxrx.c (tx_power_table, set_power_dBm): moved transmit power
table selection out of set_power_dBm
- include/misctxrx.h (tx_power_dBm2step, tx_power_step2dBm),
lib/misctxrx.c (tx_power_dBm2step, tx_power_step2dBm, set_power_dBm):
moved conversion functions out of set_power_dBm and made them globally
available
- atrf-txrx/atrf-txrx.c (tx_pwr_230, tx_pwr_231, set_power): moved to
lib/misctxrx.c
- include/misctxrx.h, lib/misctxr.c (set_power_step, set_power_dBm):
separated dBm to index conversion from the actual operation
- atrf-txrx/atrf-txrx.c (main): use new set_power_dBm instead of old
set_power
- atnet.c: introduced descriptor structure, replacing direct netio handle
- atnet.c (reply, error): moved global variables into descriptor
- atnet.c (atnet_reg_read, atnet_interrupt): when complaining about an
invalid response, skip the leading "+"
- atusb.c: introduced descriptor structure, replacing direct USB device
handle
- atusb.c (error): moved global variable into descriptor
- driver.h (atusb_dev_handle), atusb.c (atusb_dev_handle), atrf.c
(atrf_usb_handle): call driver to perform the no longer trivial
translation
- atnet.c: driver "net", which accessed hardware via atrf-proxy
- Makefile (OBJS): added atnet.o
- driver.h (atnet_driver), atrf.c (drivers): added the atnet driver
- atrf.c (drivers): moved the driver list closer to the top
- usbopen.h (usb_unrestrict), usbusb.c (usb_unrestrict): drop ID and
path restrictions
- atusb.c (atusb_open): call usb_unrestrict to remove restrictions
- lib/Makefile (OBJS), include/cwtest.h (cw_test_begin, cw_test_end),
lib/cwtest.c (enter_test_mode_230, enter_test_mode_231,
cw_test_begin, cw_test_end): moved constant wave test mode setup
over from atrf-txrx.c
- atrf-txrx/atrf-txrx.c (transmit_pattern): use functions from cwtest.o
Examples:
usb:1/6 select logical device 6 on bus 1
usb:1-3.1.4 starting at bus 1, choose ports 3, 1, and 4
- usbopen.c (initialize, open_usb): moved libusb initialization to
separate function, to allow for sharing
- usbopen.h (restrict_usb_path), usbopen.c (restricted_path, open_usb,
restrict_usb_dev, restrict_usb_by_dev, read_num, restrict_usb_by_port,
restrict_usb_path): added mechanism to restrict USB path
- atusb.c (atusb_open): if an argument is given, call restrict_usb_path
with it
We shared it across projects so far, but since the code will be further
customized, it's better to keep it local (at least for a while).
- usbopen.h, usbopen.c: moved over f32xbase/include/usb.h and
f32xbase/lib/usb.c (for further customization)
- Makefile (CFLAGS, OBJS_host): use usbopen.o instead of usb.o from
f32xbase
- atusb.c: use usbopen.h instead of usb.h from f32xbase (also removes
include path ambiguity)
- include/atrf.h (atrf_ben_regs), lib/atrf.c (atrf_ben_regs),
lib/driver.h (atben_regs), lib/atben.c (atben_regs): new function to
get the mmap'ed registers in a less disgusting way
- atrf-xtal/atben.c (base, ben_setup): cleaned up the horrible layering
violation
- include/atrf.h (atrf_default_driver_name),
lib/atrf.c (atrf_default_driver_name): return the name of the default
driver, or "none" if no drivers are defined
Case-sensitive is the Unix way, and so is avoiding unnecessary upper-case.
- atben.c (atben_driver): changed name from "Ben" to "ben"
- atusb.c (atusb_driver): changed name from "USB" to "usb"
- atrf.c (select_driver): made driver name matching case-sensitive
atrf_open(NULL) maintains the old behaviour. To select a driver, use
atrf_open("name") or atrf_open("name:driver-specific-arguments")
The driver name is "ben" or "usb".
- include/atrf.h (atrf_open), lib/atrf.c (do_atrf_open, atrf_open):
atrf_open now requires the string argument for driver selection
- atrf-id/atrf-id.c (main), atrf-reset/atrf-reset.c (main),
atrf-rssi/atrf-rssi.c (main), atrf-trim/atrf-trim.c (main),
atrf-txrx/atrf-txrx.c (main), atrf-xtal/atrf-xtal.c (main):
changed atrf_open() to atrf_open(NULL)
- atrf.c (atrf_open, select_driver, do_atrf_open): added infrastructure
for passing the driver name and further parameters to atrf_open
- atrf.c (struct atrf_dsc): made "driver" constant
- driver.h (struct atrf_driver), atben.c (atben_open), atusb.c
(atusb_open): added string argument to the "open" function
- atusb.c (atusb_driver): corrected unterminated comment
- Makefile (DIRS): added atrf-xtal
- atrf-xtal/Makefile: build atrf-xtal for the Ben or do nothing elsewhere
- atrf-xtal/atrf-xtal.h, atrf-xtal/atrf-xtal.c: diagnostic utility to
determine the transceiver's crystal frequency
- atrf-xtal/atben.c: dirty low-level driver for ATBEN
- include/atrf.h, lib/atrf.c (atrf_slp_tr): new function to set the SLP_TR
line
- lib/driver.h (struct atrf_driver): added driver function slp_tr
- lib/atusb.c (atusb_driver): we dont support slp_tr yet
- lib/atben.c (atben_slp_tr, atben_driver): implement SLP_TR control
- include/atrf.h (atrf_set_clkm), lib/atrf.c (atrf_set_clkm): set or
disable CLKM
- lib/driver.h (atrf_set_clkm_generic), lib/atrf.c (atrf_set_clkm_generic):
generic function to set CLKM without restrictions
- lib/driver.h (struct atrf_driver): added driver operation "set_clkm"
to set CLKM
- lib/atusb.c (atusb_set_clkm, atusb_driver): restrict CLKM on ATmega32U2
boards
- atrf-txrx/atrf-txrx.c (init_txrx): use atrf_set_clkm to set CLKM
- atrf-txrx/atrf-txrx.c (init_txrx, main): pass CLKM frequency in MHz
instead of code point
- atrf.c (struct atrf_dsc): added field "chip_id" to cache chip ID
- atrf.c (identify, atrf_identify): moved identification logic to new
function
- atrf.c (atrf_open, atrf_identify): cache chip ID when opening the
device and return ID from cache
- atrf-txrx.c (set_rate, main): allow setting a non-standard high data
rate on the AT86RF231
- atrf-txrx.c (usage, main): added option -r to select the data rate
- atrf-txrx.c (struct ping, enum rx_res, ping_tx, ping_rx, ping): send
back a packet containing a locally generated sequence number and the
last sequence number received whenever a packet arrives
- atrf-txrx.c (usage, main): added option -P to select ping mode
- Makefile: added perdump
- perdump.h, perdump.c: read and analyze a PER dump in pcap format
- per-text.c: report PER test results as text on the console
When some interrupt(s) happened but the one(s) wait_for_interrupt was
waiting for weren't among them, it printed the list of interrupts
even if they were all in "ignore". This made sequences like RX_START
followed by TRX_END unnecessarily noisy.
Now, wait_for_interrupt only prints the pending interrupts if at
least one of them is not in "ignore".
- atrf-txrx.c (usage, main): changed option -B to -P
- atrf-txrx.c (usage): "BER test mode" is now "PER test mode"
- atrf-txrx.c (main): mode_ber is now mode_per
- pcap.h (PCAP_FILE_MAGIC): define the pcap file magic number
- atrf-txrx.c (write_pcap_hdr): use PCAP_FILE_MAGIC instead of open-coding
the magic number
- atrf-txrx.c (main): indicate mode of operation in variable "mode" instead
of dual-using "cont_tx"
- atrf-txrx.c (usage, main): added option -B to enter BER test pattern
transit mode
- atrf-txrx.c (transmit_pattern): transmit raw frames with a cyclic frame
number
- pcap.h: basic pcap file structure definitions
- atrf-txrx.c (usage, main): added option "-o file" to write received
frames to a pcap file instead of displaying them
- atrf-txrx.c (receive): moved code to receive and display a single message
into new function receive_message
- atrf-txrx.c (write_pcap_hdr, write_pcap_rec, receive_pcap): receive
messages into a pcap file
- atrf-txrx.c (usage): split options and arguments for different modi into
separate sections
- atrf-txrx.c (usage): moved details for common options to a separate
section
- atrf-txrx.c (usage): added -C mhz to synopsis
- Makefile.common (MACROS_ben_jlime, MACROS_ben_openwrt), lib/atrf.c
(atrf_open): changed HAVE_USD to HAVE_BEN
- lib/atben.c: changed "uSD version" in title to "Ben 8:10 card version"
- lib/atrf.c, lib/atben.c: changed all occurrences of "atusd" to "atben"
- lib/atusd.c: renamed CLK to SLP_TR
- lib/atusd.c (atusd_cycle, atusd_cycle, atusd_open, atusd_close):
#ifdef'ed all uses of CLK and changed them to SLP_TR (along with the
change in function)
- atrf-txrx/atrf-txrx.c (init_txrx): always use the crystal oscillator
According to the data sheet, it has to be enabled. The Software Model
doesn't mention it. Experiments show that it's indeed useless and just
adds noise.
- atrf-txrx.c (usage, main): added option -C mhz to enable the CLKM output
and to set its frequency
- atrf-txrx.c (init_txrx): if requested, enable CLKM and set to maximum
drive strength
- atrf-txrx.c (init_txrx): unmask all interrupts for 231 compatibilit,
where masked interrupts are now indicated in IRQ_STATUS
- atrf-txrx.c (init_txrx): on the 231, wait for (and clear) the CCA_ED_DONE
interrupt when entering TRX_OFF after reset
- tools/Makefile (upload): make destinastion host name ("ben" or "jlime")
depend on TARGET
- tools/Makefile.common (CC_ben, CFLAGS_ben, LDLIBS_ben, MACROS_ben):
renamed to *_openwrt and added *_jlime equivalents
- tools/atrf-rssi/Makefile: added settings to use SDL_gfx on Jlime
- tools/lib/Makefile (OBJS_ben): renamed to OBJS_ben_openwrt and added
OBJS_ben_jlime
- atrf-txrx.c (test_mode): moved test mode setup to enter_test_mode_230
- atrf-txrx.c (enter_test_mode_231): enter test mode on AT86RF231 (untested)
- atrf-txrx.c (test_mode): reset AT86RF231 register 0x1c when leaving
- atrf-txrx.c (tx_pwr, tx_pwr_230, tx_pwr_231, set_power): table of power
values depends on chip
- atrf-txrx.c (set_power): location of TX_AUTO_CRC_ON and use of
REG_PHY_TX_PWR depends on chip
- tools/lib/atrf.h, tools/lib/atrf.c (atrf_identify): added chip
identification function to library
- tools/atrf-id/atrf-id.c (show_info): print information returned by
atrf_identify
- tools/atrf-id/atrf-id.c (show_info): decode JEDEC manufacturer ID
- tools/atrf-*/atspi-*.c: renamed to atrf-*.c
- tools/atrf-*/Makefile (MAIN): updated name of program
- tools/atrf-*/*.c: updated path in title comment
- tools/atspi-id/: renamed to atrf-id
- tools/atspi-reset/: renamed to atrf-reset
- tools/atspi-rssi/: renamed to atrf-rssi
- tools/atspi-trim/: renamed to atrf-trim
- tools/atspi-txrx/: renamed to atrf-txrx
- tools/Makefile: renamed directories from atspi-* to atrf-*
e lib/misctxrx.o
- atspi-txrx/atspi-txrx.c (usage): rearranged description of -T
- atspi-txrx/atspi-txrx.c (usage, main): option -f freq to specify the
channel by frequency
- atspi-txrx/atspi-txrx.c (set_power): make enabling the CRC optional
(this is necessary for test mode, which doesn't seem to work if the CRC
is selected)
- atspi-txrx/atspi-txrx.c (test_mode): emit a constant wave in test mode
- atspi-txrx/atspi-txrx.c (usage, main): new option -T <delta> to emit a
constant wave -2 MHz, -0.5 MHz, or +0.5 MHz from the nominal carrier
frequency
- include/atspi.h, lib/atspi.c: new function atspi_test_mode to enter test
mode
- lib/driver.h (struct atspi_driver): add backend function test_mode
- lib/atusb.c (atusb_test_mode), lib/atusb.c (atusb_driver): enter test
mode
- lib/atusd.c (atusd_driver): test mode is not supported
- atspi-rssid/gui.c (sweep, label_channels): moved geometry values to
#defines
- atspi-rssid/gui.c (CBIG, CSMALL, label_channels): moved color values to
#defines
- tools/Makefile.common: CFLAGS and OBJS can now be target-specific
- tools/atspi-rssi/Makefile: add SDL, SDL_gfx, and the GUI object files
when building on the host
- tools/atspi-rssi/Makefile: set -DHAVE_GFX when building on the host
- tools/atspi-rssi/atspi-rssi.c (usage, main): new option -g to use GUI
mode
- tools/atspi-rssi/atspi-rssi.c (main): rename variable for the number of
sweeps in non-GUI mode from "sweeps" to "arg", since it may have other
uses in the future
- tools/atspi-rssi/digit.h, tools/atspi-rssi/digit.c: draw 7 segment style
digits
- tools/atspi-rssi/zgrid.h, tools/atspi-rssi/zgrid.c: display a surface in
faux 3D with SDL/SDL_gfx
- tools/tools/atspi-rssi/gui.h, tools/atspi-rssi/gui.c: display RSSI scans
as a scrolling 3D profile
- atrf/: rename to atusb/
- atrf/wpan-atrf.pro, atrf/wpan-atrf.sch, atrf/wpan-atrf.brd,
atrf/wpan-atrf.cmp: rename to atusb.*
- atrf/Makefile: change ben-wpan to atusb
- atrf/atusb.pro (LastNetListRead): update for name change
- tools/Makefile.common (CFLAGS): change fw/ include location from atrf/
to atusb/
if it differs by more than 0.01 dBm from the level specified
- tools/atspi-txrx/Makefile (LDLIBS): added -lm, for fabs()
- tools/atspi-txrx/atspi-txrx.c (transmit, usage, main): add optional
command-line argument with the number of times to send the message
- tools/atspi-txrx/atspi-txrx.c (receive, transmit, die, main): return and
clean up on ^C
- tools/tools/lib/misctxrx.c (wait_for_interrupt) return and raise SIGINT
for the caller's signal handler on ^C
- atrf/fw/include/atspi/ep0.h enum atspi_requests), atrf/fw/atspi/ep0.c
(my_setup): new command ATSPI_POLL_INT to poll IRQ_RF
- atrf/fw/atspi/ep0.c (my_setup): ATSPI_BUILD sent one byte too many
- tools/lib/atusb.c (atusd_interrupt, atusb_driver): implemented interrupt
polling
- tools/lib/atusd.c: added section title for the RF interrupt function
- tools/atspi-rssi/atspi-rssi.c: removed unnecessary inclusion of
atspi/ep0.h
- tools/atspi-rssi/atspi-rssi.c (sweep): instead of fixed delay, wait for
the PLL lock interrupt
- tools/atspi-rssi/atspi-rssi.c (die, main): catch SIGINT to exit cleanly
- tools/atspi-rssi/atspi-rssi.c (main): shut down properly when done
- tools/atspi-rssi/atspi-rssi.c (usage): print "usage:" before the program's
name
- tools/atspi-txrx/atspi-txrx.c: cleaned up includes - we need stdint.h but
we don't need atspi/ep0.h
- tools/atspi-txrx/atspi-txrx.c (wait_for_interrupt),
tools/include/misctxrx.h (wait_for_interrupt), tools/lib/Makefile (OBJS),
tools/lib/misctxrx.c (wait_for_interrupt): moved wait_for_interrupt from
atspi-txrx to the atspi library, so that we can share it
- tools/atspi-txrx/atspi-txrx.c (receive, wait_for_interrupt): moved wait
for interrupt logic to separate function and made it more versatile
- tools/atspi-txrx/atspi-txrx.c (init_txrx, receive): clear interrupts in
init_txrx now, so that also transmit has a clear interrupt register
- tools/atspi-txrx/atspi-txrx.c (set_channel): since we're in TRX_OFF,
don't wait for PLL lock
- tools/atspi-txrx/atspi-txrx.c (receive): wait for PLL lock interrupt
after activating receiver
- tools/atspi-txrx/atspi-txrx.c (transmit): wait for PLL lock interrupt
after activating the PLL
- tools/atspi-txrx/atspi-txrx.c (transmit): wait for TRX_END interrupt
after sending a frame
- tools/atspi-txrx/atspi-txrx.c (receive): report the Energy Density (ED)
after receiving a frame
- tools/atspi-txrx/atspi-txrx.c (main): shut down the board with
atspi_close, so that we can hot-swap safely
- tools/lib/atusd.c (spi_send_partial, spi_send): removed the old spi_send
and renamed spi_send_partial to spi_send
- tools/lib/atusd.c (atusd_cycle, spi_send, spi_recv, atusd_open): updated
for removal of SLP_TR and split of MxSx into MOSI and MISO
- tools/lib/atusd.c (atusd_reset_rf, atusd_open): added delays to precharge
the capacitors
- tools/lib/atusd.c (atusd_reset, spi_data_in, spi_data_out, spi_finish):
removed functions for obsolete hardware features
- tools/lib/atusd.c (atusd_reg_read): removed calls to removed functions
- tools/lib/atusd.c (atusd_buf_write, atusd_buf_read, atusd_driver): new
buffer read/write functions
- tools/atspi-txrx/atspi-txrx.c (init_txrx): set the internal osciallator
trim only in the USB version. Switch to the external oscillator in the
uSD version.
- tools/atspi-rssi/atspi-rssi.c (sweep), tools/atspi-txrx/atspi-txrx.c
(set_channel): wait for the PLL to settle after setting the channel
- tools/include/atspi.h, tools/lib/atspi.c (atspi_interrupt),
tools/lib/driver.h (struct atspi_driver), tools/lib/atusd.c
(atusd_interrupt): new function to poll the interrupt line
- tools/atspi-txrx/atspi-txrx.c (receive): only read REG_IRQ_STATUS if
there is a pending interrupt
- tools/atspi-id/atspi-id.c (usage): print "usage:" as well
- tools/Makefile (upload): upload the atspi tools to the Ben
