The structs defined in these header files should be the same as the
structes used by the platform code otherwise it will cause strange
runtime errors. By removing them from compat-wireless we will get a
compile error instead of a runtime error if they are out of sync.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33006 3c298f89-4303-0410-b956-a3cf2f4a3e73
* remove use_et, all supported drivers are using mii ioctls
* remove robo.phy_addr, phy_addr was always set to ROBO_PHY_ADDR.
* remove support for old kernel versions
* do_ioctl is allways called with buff == NULL
* use if_mii
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33002 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since we are overriding TARGET_CXX with the g++-uc wrapper when
we use cmake it expects to find g++-uc in the TOOLCHAIN_DIR.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32928 3c298f89-4303-0410-b956-a3cf2f4a3e73
Too many modules were removed, while only the octeon module was meant to be
removed, fix that.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32909 3c298f89-4303-0410-b956-a3cf2f4a3e73
When standalone ldd is selected in config the binary is installed in /usr/bin/ldd.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32891 3c298f89-4303-0410-b956-a3cf2f4a3e73
I did not add the last patch, because it add some stubs for the flash drivers and our patches have to be changed for that, if the flash support in bcma is able to do something I will integrate it.
This also contains 3 additional patches fixing some bugs in bcma.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32880 3c298f89-4303-0410-b956-a3cf2f4a3e73
With the BRCM47xx image I have built (Linksys E3000), there are additional
writes following the completion of "mtd_replace_jffs2" which invalidate the
'trx_fixup' performed by 'mtd_replace_jffs2'. Moving the 'trx_fixup' to somewhere
after all writes have completed fixes the problem. I also noticed that 'erasesize'
used to compute 'block_offset' in 'mtd_fixtrx' is used before it is computed by
'mtd_check_open'; moving the call to 'mtd_check_open' up a few lines fixes this.
Unlike 'mtd_fixtrx', 'trx_fixup' appears to assume that the TRX header is always at
offset 0; which may be the cause of the problem described in Ticket #8960.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32866 3c298f89-4303-0410-b956-a3cf2f4a3e73
add patched needed to pass more parameters to the IBSS JOIN command
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32828 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Raspberry Pi / brcm2708 / 2835
Signed-off-by: Ian Ridge <ianridge [at] gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32825 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the ext4 filesystem support to mountd. Tested with ext2, ext3
and ext4 partitions.
Signed-off-by: Jaroslaw Swierczynski <jarek1701@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32818 3c298f89-4303-0410-b956-a3cf2f4a3e73
Forgot to do make package/mac80211/update, so the previously posted patch wasn't
in sync with compat-wireless. Now fixed.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32817 3c298f89-4303-0410-b956-a3cf2f4a3e73
Preserve alphabetical order on KCONFIG and description for consistency with other module packages
This reverts commit r32775.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32791 3c298f89-4303-0410-b956-a3cf2f4a3e73
- add device list in usage screen
- support resetting by bus/device number, by produc:vendor id or by device name
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32741 3c298f89-4303-0410-b956-a3cf2f4a3e73
iConnect board tested by:
Tim Fletcher <tim@night-shade.org.uk>
Wojciech Dubowik <wojciech.dubowik@neratec.com>
DockStar board tested by:
Martin Mueller <mm@sig21.net>
RaidSonic ICY BOX NAS6210 board tested by:
Luka Perkov <uboot@lukaperkov.net>
SheevaPlug was not tested but support for SheevaPlug is taken from upstream
uboot and it is not reported to be broken there.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32717 3c298f89-4303-0410-b956-a3cf2f4a3e73
Here is a newer version of the patch:
Enable the real ALSA midi interface (seq) in the kernel. The existing
rawmidi interface is still present. This allows for the alsa midi
utilities to work.
Signed-off-by: Adam Goode <adam@spicenitz.org>
[b_tsiligiannis: replaced $(LINUX_KMOD_SUFFIX) with .ko]
Signed-off-by: Vasilis Tsiligiannis <b_tsiligiannis@silverton.gr>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32712 3c298f89-4303-0410-b956-a3cf2f4a3e73
- remove unused variables
- simply ignore command line args which belong to not enabled features
- resolve peer address at accept() time, should solve (#11850)
- remove floating point operations where possible
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32704 3c298f89-4303-0410-b956-a3cf2f4a3e73
- avoid closing descriptors before removing them from uloop (#11755, #11830)
- do not auto-initialize ubus if no prefix is set (#11832)
- remove extraneous client context pointer from cgi and lua states
- code cleanups and debug message changes
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32651 3c298f89-4303-0410-b956-a3cf2f4a3e73
Watch child read pipe end for data instead of relying on socket write
notification to process cgi data, should lower cpu consumption during
requests on weaker devices.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32640 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a config list to the 'config dnsmasq' section to specify fixed DNS
addresses.
For example:
config dnsmasq:
[snip]
list address '/example.com/192.168.0.1'
will result in the argument '-A /example.com/192.168.0.1' to the dnsmasq
options. This configures dnsmasq to return the specified IP for any
queries to '*.example.com' names.
Useful for overriding lookups to a range of DNS names.
[jow: "append args" -> "xappend", "-A" -> "--address"]
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32624 3c298f89-4303-0410-b956-a3cf2f4a3e73
-T, --local-ttl=<time>
When replying with information from /etc/hosts or the DHCP leases
file dnsmasq by default sets the time-to-live field to zero, meaning
that the requestor should not itself cache the information. This is
the correct thing to do in almost all situations. This option allows a
time-to-live (in seconds) to be given for these replies. This will
reduce the load on the server at the expense of clients using stale
data under some circumstances.
[jow: change -T to --local--ttl to conform with the other options]
Signed-off-by: Andrew Byrne <openwrt@andy.id.au>
openwrt-devel mailing list
openwrt-devel@lists.openwrt.orghttps://lists.openwrt.org/mailman/listinfo/openwrt-devel
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32623 3c298f89-4303-0410-b956-a3cf2f4a3e73
Set PATH in non-interactive logins to include /sbin paths,
so to be consistent with what is currently set in /etc/profile
for interactive shells.
[jow: reapply with current patch level, fix inner patch, refresh]
Signed-off-by: Gui Iribarren <gui@altermundi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32620 3c298f89-4303-0410-b956-a3cf2f4a3e73
When mtd alters the fis partition table it assumes that the first partition
table entry also is the first logical parition table entry. For instance our
table could look like this (irrelevant partitions put aside):
* vmlinux.bin.l7 0xA8710000
* rootfs 0xA8030000
Here mtd would assume vmlinux.bin.l7 being the first partition and use its
address to calculate the size and offset which ultimately leads to a broken
partition table.
This patch alters the behavior by checking what partition has the smaller
address to do the calculations based on that address.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32601 3c298f89-4303-0410-b956-a3cf2f4a3e73
The offset parameter can be used to write the data at the offset
instead of writing it to the beginning of the partition.
Signed-off-by: Marek Linder <lindner_marek@yahoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32600 3c298f89-4303-0410-b956-a3cf2f4a3e73
Busybox udhcpc dropped support for the -c option, instead it can be emulated by using -x 0x3d:id,
change the dhcp protocol script accordingly and filter all colons from the id while we're at it.
This change supersedes http://patchwork.openwrt.org/patch/1810/
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32573 3c298f89-4303-0410-b956-a3cf2f4a3e73
- add_local_domain defaults to 1 and controls whether the local domain is written as search directive to the local resolv.conf
- add_local_hostname defaults to 1 and controls whether A and PTR records are created automatically for the local hostname
These change supersedes http://patchwork.openwrt.org/patch/2207/ and http://patchwork.openwrt.org/patch/2208/
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32570 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds a new boolean option, fqdn, to the "config dnsmasq" section of
/etc/config/dhcp. The default is off. When set on, it enables the dhcp-fqdn
option to dnsmasq. dhcp-fqdn causes dnsmasq's DNS server to not resolve
unqualifed local hostnames. The "domain" option is required when using "fqdn".
Local hostnames will remain available for lookup using fully-qualified names.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32569 3c298f89-4303-0410-b956-a3cf2f4a3e73
dnsmasq currently permits dhcp_options to be specified only in "config dhcp"
sections of /etc/config/dhcp. When dnsmasq is providing DHCP service for
multiple subnets and there are multiple "config dhcp" sections without "option
ignore", it makes sense to allow dhcp_options that should apply globally in
the "config dnsmasq" section of /etc/config/dhcp. dhcp_option is a list option.
[jow: rework patch to apply after dhcp-option-force handling got introduced]
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32568 3c298f89-4303-0410-b956-a3cf2f4a3e73
Extroot works fine when the target device is specified by a path. It fails
however if the device is specified by UUID (the target partition gets mounted
much later by hotplug hooks). This is because the blkid command is no longer
compiled into BusyBox (since changeset [1]) so it's unavailable for the
preinit phase.
The closest bug report I was able to find is [2], although the reporting person
mentions that /tmp/overlay-disabled showed up which wasn't there in my case.
This patch sets PATH and LD_LIBRARY_PATH environment variables so that the
blkid command installed on the target device can be used by that particular
preinit script.
[1] https://dev.openwrt.org/changeset/26245
[2] https://dev.openwrt.org/ticket/10653
Signed-off-by: Jaroslaw Swierczynski <jarek1701@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32567 3c298f89-4303-0410-b956-a3cf2f4a3e73
l2tp_ppp needs to be loaded after pppox, otherwise it ends up like this:
l2tp_ppp: Unknown symbol pppox_ioctl (err 0)
...
during boot.
I also fixed the dependency, it should be pppox rather than pppoe.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32562 3c298f89-4303-0410-b956-a3cf2f4a3e73
A year of testing in the cerowrt project shows not using timestamps
to be a very bad idea in nearly any TCP at speeds above a few Mbit.
Lastly sack/dsack help on recovery from larger amounts of packet
loss.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32513 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi,
yes, it is true...
In the standard, unpatched trunk is zlib_inflate.ko compiled, but not included
in any package... So, my previous version was functional, but with system bug.
Here is fixed patch.
On Wed, Jun 13, 2012 at 05:00:02PM +0200, Jo-Philipp Wich wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> - -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Hi.
>
> Shouldn't you also add CONFIG_ZLIB_DEFLATE to KCONFIG then?
>
> ~ Jow
> - -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.4.12 (GNU/Linux)
> Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org/
>
> iEYEARECAAYFAk/YqrcACgkQdputYINPTPM6dgCfYDgzK1XHiKDJNSdc/+HgIoRp
> HSgAoKdUxcqXzHqTLiyEkiQqCnDuuVmu
> =0DUX
> - -----END PGP SIGNATURE-----
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.4.12 (GNU/Linux)
> Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org/
>
> iEYEARECAAYFAk/YqvIACgkQdputYINPTPNMagCePNwPSYHfoCd5eXywQ+sTATqQ
> 2CQAoJW/Fez+DqflHlJVcvng/LvsfrCm
> =s6B0
> -----END PGP SIGNATURE-----
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
Signed-off-by: Michal Heppler <mhepp@ics.muni.cz>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32444 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi,
I found that openssl did not compile on the uml target under x86_64. The
attached patch should
correct this and is working for me. Is this the right way to do it?
thanks,
Thomas
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32443 3c298f89-4303-0410-b956-a3cf2f4a3e73
kmod-ipt-nathelper-extra is missing the package nf_conntrack_broadcast.ko
if it is not included into the kmod-ipt-nathelper-extra packge the modules
nf_conntrack_snmp and nf_nat_snmp_basic cant get loaded:
[ 44.500000] nf_conntrack_snmp: Unknown symbol nf_conntrack_broadcast_help (err 0)
[ 44.664000] nf_nat_snmp_basic: Unknown symbol nf_nat_snmp_hook (err 0)
Signed-off-by: Peter Wagner <tripolar@gmx.at>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32434 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for manually configuring 6rd tunnels. It depends on
the netifd patches I sent earlier, which add 6rd support.
A basic interface configuration looks like:
config interface 'wan6'
option proto '6rd'
option peeraddr '192.0.2.1'
option ip6prefix '2123::'
option ip6prefixlen '16'
option ip4prefixlen '0'
Where ip4prefixlen is optional and actually defaults to 0, which would use all
bits of the IPv4 in the calculated IPv6 subnet.
I believe it should be possible to configure a regular 6to4 tunnel using this,
and that we may want to merge the two eventually, but there are some larger
differences between the two at the moment:
- 6rd addresses can be more difficult to calculate. My ISP, for example, has
a setup with a v6 mask of 43 bits, and a v4 mask of 19.
- 6to4 has support for configuring radvd. This is something we want, of
course, but it seems best to deal with this in a separate patch.
Just creating a new package looked like the quickest way to get this in.
This work is based on the 6in4 package, and work by Stijn Tintel.
Signed-off-by: Stéphan Kochen <stephan@kochen.nl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32431 3c298f89-4303-0410-b956-a3cf2f4a3e73
- use new default route dependencies to trigger bringup
- remove old hotplug scripts
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32428 3c298f89-4303-0410-b956-a3cf2f4a3e73
- add ppp-mod-pptp, based on patch by Daniel Golle <dgolle@allnet.de>
- add netifd integration for pptp to ppp.sh
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32197 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fix is needed to correctly set the driver to use with wpa_s in case of
IBSS/WPA-NONE. The current setting is not made correctly.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32084 3c298f89-4303-0410-b956-a3cf2f4a3e73
libmisc.a is too generic to be globally staged. It was clashing with xinetd
builds.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32066 3c298f89-4303-0410-b956-a3cf2f4a3e73
This file will contain common procedures to deal with network interfaces.
Initially provides network_get_ipaddr(), network_get_ipaddr6(),
network_get_subnet() and network_get_subnet6() to determine the
primary IP addresses or subnets of a given logical interface.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31935 3c298f89-4303-0410-b956-a3cf2f4a3e73
- rewrite large parts of the server, use uloop event driven structure
- support concurrent requests and make the upper limit configurable
- implement initial version of HTTP-to-ubus JSON proxy and session.* namespace
- add compile time support for debug information
- code style changes
- bump package revision
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31931 3c298f89-4303-0410-b956-a3cf2f4a3e73
The option 'force' when set to '1' will transform a dhcp-option to dhcp-option-force instead in the config.
This is useful for forcing options to be sent back to a client (even options it didn't ask for).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31816 3c298f89-4303-0410-b956-a3cf2f4a3e73
On my network, I have a variety of machines and appliances, some of which need different configuration issues than the default options.
For example:
config host
option name 'client'
option mac '00:01:02:03:04:05'
option ip '192.168.1.20'
option tag 'acme'
config tag acme
option force '1'
list dhcp_option 'option:router,192.168.1.253'
list dhcp_option 'option:domain-name,acme.com'
list dhcp_option 'option:domain-search,acme.com,redfish-solutions.com'
which allows me to override the default router for my client's host, as well as its domain-name, and its domain-search.
this causes the following config lines:
dhcp-host=00:01:02:03:04:05,set:acme,192.168.1.20,client
dhcp-option-force=tag:acme,option:router,192.168.1.253
dhcp-option-force=tag:acme,option:domain-name,acme.com
dhcp-option-force=tag:acme,option:domain-search:acme.com,redfish-solutions.com
This could be useful elsewhere, for instance, if you have an IP CCTV that you don't want to have a default-route, etc.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31815 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also fix build errors in the ep80579-drivers package.
Compile tested only.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31802 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also remove trailing whitespaces from the Makefile.
Based on a patch by M. Braun.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31701 3c298f89-4303-0410-b956-a3cf2f4a3e73
On slower devices wifi drivers might take too long for detecting
devices, resulting in the wifi detect call not seeing them.
This was observed on a bcm6348 with bcm4318 wifi. Adding a one second
pause was enough for b43 to expose the device.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31639 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWrt does not support kernel version <= 2.6.36 any more, remove all modules only build for those kernels and all conditions specific for those kernel versions.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31634 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was remove in kernel 2.6.38 and is not needed any more.
The last commit (r31631) has the wrong message, kmod-usb-phidget was removed in kernel 2.6.30.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31632 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was remove in kernel 2.6.38 and is not needed any more.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31631 3c298f89-4303-0410-b956-a3cf2f4a3e73
kmod-video-konica was removed from kernel 2.6.38 and is now replaced by kmod-video-gspca-konica
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31628 3c298f89-4303-0410-b956-a3cf2f4a3e73
These two modules where removed from kernel with kernel version 2.6.36, use kmod-video-gspca-ov519 instead.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31627 3c298f89-4303-0410-b956-a3cf2f4a3e73
Passes the document-root to the Lua handler by placing it in uhttpd.docroot.
It could alternatively be placed in env.DOCUMENT_ROOT which would more closely
resemble the CGI protocol; but would mean that it is not available at the time
when the handler-chunk is loaded but rather not until the handler is called,
without any code savings.
Signed-off-by: David Favro <openwrt@meta-dynamic.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31571 3c298f89-4303-0410-b956-a3cf2f4a3e73
My apologies, the 2nd of those patches had a syntax error -- that's what
I get for making a last-minute edit, even to the comments, without
testing! :-p
Here is the corrected patch.
-- David
From d259cff104d2084455476b82e92a3a27524f4263 Mon Sep 17 00:00:00 2001
From: David Favro <openwrt@meta-dynamic.com>
Date: Fri, 27 Apr 2012 14:17:52 -0400
Subject: [PATCH] uhttpd URL-codec enhancements.
* uh_urlencode() and uh_urldecode() now return an error condition for
buffer-overflow and malformed-encoding rather than normal return with corrupt
or truncated data. As HTTP request processing is currently implemented, this
causes a 404 HTTP status returned to the client, while 400 is more
appropriate.
* Exposed urlencode() to Lua.
* Lua's uhttpd.urlencode() and .urldecode() now raise an error condition for
buffer-overflow and malformed-encoding rather than normal return with
incorrect data.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31570 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Fixed output-buffer-overflow bug in uh_urlencode() and uh_urldecode() [tested
input-buffer index against output-buffer length]. In reality, this would not
typically cause an overflow on decode, where the output string would be
expected to be shorter than the input string; and uh_urlencode() seems to have
been unreferenced in the source.
* Fixed bug: uh_urlencode() and uh_urldecode() both read one extra byte from the
input-string. While this could manifest in C code, the result was most
egregious when called from Lua, where it caused an extra null byte to be
embedded at the end of the output string.
* uh_urlencode() cleanup: removed redundant bitwise-and.
Signed-off-by: David Favro <openwrt@meta-dynamic.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31569 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: export xt_layer7.h for all kernel versions]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31566 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existing code is fairly broken. It assumes you're using Legacy IP, and
it assumes that the server is reachable via your default route. Via the
first default route in the 'route -n' output, in fact, regardless of metric.
Fix all those problems by using 'ip route get' to really find the *current*
route to the server, and install a host-specific route to match.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31565 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch by Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31522 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch makes several changes to the util-linux(-ng) package:
* rename to util-linux (official name now, util-linux-ng got merged)
* bump to last stable version 2.21.1 (was 2.13.0.1 before)
* add several new packages
* sort packages within Makefile
* remove patches which got merged upstream
This patch makes some changes to the e2fsprogs package:
* bump to last stable version 1.42.2
* libraries moved from e2fsprogs to util-linux - take care of that
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31499 3c298f89-4303-0410-b956-a3cf2f4a3e73
This commit fixes build breakage in package/kernel leading to missing
subsequent kmods like kmod-usb-serial, this should fix the missing
packages in ar71xx builds.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31477 3c298f89-4303-0410-b956-a3cf2f4a3e73
Any modifications in target/linux/*/modules.mk would not come into effect for
subsequent "make menuconfig" unless we delete ./tmp.
Signed-off-by: kalyan <kalyanatejaswi@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31442 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without module_pci_driver being defined the pci drivers do not get registered.
Should fix#11332
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31437 3c298f89-4303-0410-b956-a3cf2f4a3e73
hi
Another version, in this one the enable_server option is in the timeserver ntp part of the "system" config file
You can patch trunk and bacfire (tested both)
You can put busybox ntpd in client mode (if you put server), in client & server (by putting enable_server to 1, ntpd listen to udp 123), and also in server mode only (if you didn't put any servers in the config and still put enable_server 1, ntpd will answer with the time of the router)
I've replaced "config_foreach getpeers timeserver" with "config_get peers ntp server" because we want ntp timeserver, not random ones (to pre-answer if someone want to say that it's intrusive ...)
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
Le 27/03/2012 20:41, Etienne Champetier a écrit :
> I've now tested my trunk patch and it works fine
> But I still can't find were $PROG is defined (is this a mistake, or some sort of built in variable???)
> (I've made some grep and nothing)
>
> Le 23/03/2012 02:19, Philip Prindeville a écrit :
>> Maybe:
>>
>> [ -n "$PROG" -a -x "$PROG" ] || return 1
>>
>> instead?
>>
>>
>> On 3/22/12 4:34 PM, Etienne Champetier wrote:
>>> Hi
>>>
>>> The 2 attached patchs (trunk & bacfire) add busybox ntpd enable_server option, as busybox ntpd server is compiled by default.
>>> We only need 1 client/server daemon (olipro patch was launching 2 daemons)
>>> I've fully tested the bacfire patch, and as i don't have a running openwrt trunk i'm not sure for the trunk patch (i'm sure about my modifications, but i'm not sure about "[ -x $PROG ] || return 1", as "$PROG" isn't defined ?!)
>>>
>>> Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
>>>
>>>
>>> Le 16/01/2012 01:57, Philip Prindeville a écrit :
>>>> On 1/14/12 11:37 AM, Olipro wrote:
>>>>> On Saturday 14 Jan 2012 02:45:59 Philip Prindeville wrote:
>>>>>> Don't we already have a 'disabled' option? Now we're adding an
>>>>>> 'enable_server' option?
>>>>>>
>>>>>> That seems confusing for no useful reason.
>>>>>>
>>>>> have you bothered to read what I originally wrote? your response would make
>>>>> me inclined to believe that you didn't.
>>>>>
>>>>> currently the ntpd initscript only runs it as a CLIENT - this patch enables
>>>>> you to have one instance running as a client and another as a SERVER that
>>>>> other hosts can synchronise with.
>>>>>
>>>>> Or perhaps I'm misunderstanding, what would you propose for allowing the
>>>>> built-in busybox ntpd to be utilised as a server? a separate init script
>>>>> entirely perhaps?
>>>> Or separate config sections... instead of 'config ntp' have 'config ntp-server' and 'config ntp-client'.
>>>>
>>>> -Philip
>>>>
>>>>
>>>> _______________________________________________
>>>> openwrt-devel mailing list
>>>> openwrt-devel@lists.openwrt.org
>>>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>> _______________________________________________
>> openwrt-devel mailing list
>> openwrt-devel@lists.openwrt.org
>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31374 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Introduce new Kconfig symbols VERSION_DIST, VERSION_NICK, VERSION_NUMBER and VERSION_REPO to specify distribution, release name, version and repository for a given build
- Introduce include/version.mk to provide common helpers for packages dealing with versions
- Make opkg use version.mk to populate the opkg.conf template
- Make base-files use version.mk to populate /etc/openwrt_version, /etc/openwrt_release and /etc/banner
The available placeholders are:
%D .. Replace with $(CONFIG_VERSION_DIST), default to "OpenWrt"
%d .. Like %D, but all characters made lowercase and spaces substituted with "_" (e.g. "openwrt")
%N .. Replace with $(CONFIG_VERSION_NICK), default to the build tree release (e.g. "Attitude Adjustment")
%n .. Like %N, but all characters made lowercase and spaces substituted with "_" (e.g. "attitude_adjustment")
%V .. Replace with $(CONFIG_VERSION_NUMBER), default to the build tree release (e.g. "r31262")
%v .. Like %V, but all characters made lowercase and spaces substituted with "_"
%C .. Replace with $(CONFIG_VERSION_NUMBER), default to "Bleeding Edge"
%c .. Like %C, but all characters made lowercase and spaces substituted with "_" (e.g. "bleeding_edge")
%U .. Replace with $(CONFIG_VERSION_REPO), default to "http://downloads.openwrt.org/snapshots/trunk/%T/packages"
%R .. Replace with the current build tree revision (e.g. "r31262" or "75488c4a05b8033cf69e91874a61852db7ba9c6c")
%T .. Replace with the current target (e.g. "ar71xx")
%S .. Replace with the current target/subtarget combo (e.g. "adm5120/router_le")
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31262 3c298f89-4303-0410-b956-a3cf2f4a3e73
To supply custom network settings, it is better to embed a complete network config file using the
files/ overlay, the old image lan preconfig options are also very limited in scope and actually collide
with sysupgrade and firstboot hardware detection on at least ar71xx and possibly other targets, therfore
drop this facility.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31258 3c298f89-4303-0410-b956-a3cf2f4a3e73
We use PKG_NAME and not PKB_BASE_NAME inside OpenWrt Makefiles
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31244 3c298f89-4303-0410-b956-a3cf2f4a3e73
