65e9b62d4503849b10bedfc29bff0473760cc597
ipv6: add special mode accept_ra=2 to accept RA while configured as router
c3bccac2fa76f1619dfe4fb7b9bee69de7f066d8
ipv6: add special mode forwarding=2 to send RS while configured as router
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24195 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a fixup for the kernel to check the bcm tag of the image for a boardid in
the information1 field, and use that instead of the supplied one by cfe. This
is triggered by a + at the start of the information1 field.
Also modify the image generation to generate apropriately tagged images.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24189 3c298f89-4303-0410-b956-a3cf2f4a3e73
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24187 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24186 3c298f89-4303-0410-b956-a3cf2f4a3e73
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24185 3c298f89-4303-0410-b956-a3cf2f4a3e73
If rfkill is build as an module CONFIG_RFKILL_MODULE is set and cfg80211 will also depend on that.
Now all modules build from compat-wireless will not use rfkill.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24143 3c298f89-4303-0410-b956-a3cf2f4a3e73
No support for usb for now.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24126 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allows to use fids 0 to 7. Default is 0.
Those who will use this don't forget to `set vlan fid` every time
after `set vlan ports` if you want non default behavior.
Minor changes. Version bump.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24125 3c298f89-4303-0410-b956-a3cf2f4a3e73
The skb_reserve call prior to DMA mapping the RX skb reduced the skb
data len by 2. To not allow DMA to write behind the skb we should pass
the correct skb data len to the device.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24123 3c298f89-4303-0410-b956-a3cf2f4a3e73
