Aparently $magic_long was meant here instead of $magic when comparing with
32-bit values.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28678 3c298f89-4303-0410-b956-a3cf2f4a3e73
A miscalculation in the original patch makes OpenWrt destroy the failsafe image.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28615 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds support for the Netgear WNDR3800, it is almost the same as
the WNDR3700v2. It just has more RAM so the hd_id had to be adjusted.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28597 3c298f89-4303-0410-b956-a3cf2f4a3e73
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28571 3c298f89-4303-0410-b956-a3cf2f4a3e73
WAN is on swtich port 0 for Aztech HW550-3G.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28570 3c298f89-4303-0410-b956-a3cf2f4a3e73
This removes unnecessary duplication and simplifies led setup for new
boards. It would be a one line change most likely.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28569 3c298f89-4303-0410-b956-a3cf2f4a3e73
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28567 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28564 3c298f89-4303-0410-b956-a3cf2f4a3e73
AR8316 behind a GPIO bitbanged MDIO bus fails to drive the turnaround bit
to low despite returning a valid value. Ignore it and just use the
returned value anyway.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28422 3c298f89-4303-0410-b956-a3cf2f4a3e73
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.
Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28380 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix typo from previous submission with input-keys-polled.
Philip Prindeville - 2011-10-03 01:44:55
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28356 3c298f89-4303-0410-b956-a3cf2f4a3e73
---
Attaching the correct file this time...
Philip Prindeville - 2011-09-07 07:01:42
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28355 3c298f89-4303-0410-b956-a3cf2f4a3e73
Don't make the config more complicated than it needs to be.
Philip Prindeville - 2011-08-29 03:15:27
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28353 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi,
this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.
It also fixes two whitespace issues.
Tested with brcm47xx on both trunk and backfire branch and works as
expected.
Signed-off-by: Manuel Munz <freifunk@somakoma.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28336 3c298f89-4303-0410-b956-a3cf2f4a3e73
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28310 3c298f89-4303-0410-b956-a3cf2f4a3e73
* rebase 3.0 patches
* fold some fixes into existing patches
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28308 3c298f89-4303-0410-b956-a3cf2f4a3e73
Same hardware as WR741ND but with PoE support.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28271 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the option to enable jumbo frames on the rtl8366s
switch. This is almost exactly the same as the first patch at
https://dev.openwrt.org/ticket/7977 and it has been requested
in a comment there.
I have tested this and it successfully allows devices on the switch
using jumbo frames to communicate.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28267 3c298f89-4303-0410-b956-a3cf2f4a3e73
- don't regenerate Package index unless the packagedir changes
- remove opkg lists from rootfs, saves > 1MB uncompressed
- don't direct errors on index creation into packagelist
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28205 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since linux gets developed on x86 more than all other hardware,
hardly makes sense to have our default x86 version be trailing
by over a year.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28082 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Ed Wildgoose's alix platform driver plus my
enhancement to add GPIO soft button support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28081 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix fivebytepypo - there is no such kernel module wpad-mini :)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28049 3c298f89-4303-0410-b956-a3cf2f4a3e73
[The ESW related changes has been removed - juhosg]
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27991 3c298f89-4303-0410-b956-a3cf2f4a3e73
on some platforms, erase suspend leads to data corruption and lockups when write
ops collide with erase ops. this has been observed on the buffalo wzr-hp-g300nh.
rather than play whack-a-mole with a hard to reproduce issue on a variety of devices,
simply disable erase suspend, as it will usually not produce any useful gain on
the small filesystems used on embedded hardware.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27984 3c298f89-4303-0410-b956-a3cf2f4a3e73
- keyboard matrix driver
- SoC sound support
based on patch by KanjiMonster
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27957 3c298f89-4303-0410-b956-a3cf2f4a3e73
KanjiMonster did the right patch, I was just confused because of linux-3.0 and linux-2.6.30
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27954 3c298f89-4303-0410-b956-a3cf2f4a3e73
find_task_by_vpid is already exported by the kernel without any patches needed.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27953 3c298f89-4303-0410-b956-a3cf2f4a3e73
As this target changes often these days it is hard to support more kernel versions. Now only kernel 3.0 is supported.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27906 3c298f89-4303-0410-b956-a3cf2f4a3e73
* this adds sflash support for ssb devices
* the flash is now a platform device
* minor updates
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27902 3c298f89-4303-0410-b956-a3cf2f4a3e73
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes#9689, #9405
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27896 3c298f89-4303-0410-b956-a3cf2f4a3e73
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27895 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is breaking some devices out there such as Winchiphead CH341 adapters (#9601)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27885 3c298f89-4303-0410-b956-a3cf2f4a3e73
- runtime detect the amount of memory available
- define EBI_BASE as MPI_BASE to get rid of chip-select specific hacks
- fix GPIO control
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27880 3c298f89-4303-0410-b956-a3cf2f4a3e73
decreases CPU load with the default firewall for routing 95 mbit/s from 78% to 55%
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27878 3c298f89-4303-0410-b956-a3cf2f4a3e73
The old ieee1394 stack was removed in 2.6.37. The new firewire stack is
available for all kernel versions, but experimental for the older one, so
make both available where appropriate.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27874 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27814 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change corrects expected CPU name of Ralink RT3050, which
describes itself as RT3350 (this name is ripped off chip and elevated
to user space via /proc/cpuinfo.)
This patch fixes wired network on DIR-300 rev B and DIR-600 rev B
Signed-off-by: Slawomir Cygan <wiewior@wiewior.eu.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27804 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also make switches available under a generic name "switch<num>" for device
name agnostic access. The old device name is used as an alias for backward
compatibility.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27800 3c298f89-4303-0410-b956-a3cf2f4a3e73
Include WAN interface by default, instead of putting both ports in the LAN bridge.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27787 3c298f89-4303-0410-b956-a3cf2f4a3e73
Cut and paste cruft from borrowing from Geos platform.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27786 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some config symbols for kernel 3.0.
Thank you realopty for the patch.
This is from #9719.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27775 3c298f89-4303-0410-b956-a3cf2f4a3e73
In 240-spi.patch, spi registers for bcm6348 were all messed up. This patch fixes that.
It also fixes some spi commands for all bcm63xx.
Signed-off-by: Anthony Blakemore <stokie-ant@raverbaby.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27774 3c298f89-4303-0410-b956-a3cf2f4a3e73
Issue map read after Write Buffer Load command to ensure chip is ready
to receive data.
Signed-off-by: George Kashperko <george@znau.edu.ua>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27760 3c298f89-4303-0410-b956-a3cf2f4a3e73
ssb_pcicore_fix_sprom_core_index accesses the sprom on the pci bus but
this causes a data bus error (oops) on a SoC.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27758 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes problem with TFM allocation in cryptosoft.c
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Hauke:
* remove ubsec_ssb package and take it from ocf-linux
* use patches from ocf-linux package
* refresh all patches
* readd some build fixes for OpenWrt.
* readd CRYPTO_MANAGER dependency
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27753 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sysfs support for DMI BIOS was added in 2.6.39.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27749 3c298f89-4303-0410-b956-a3cf2f4a3e73
As the Geos box includes an ADSL modem that's targeted towards PPPoE, PPPoA, and bridged utilization, including these useful tools allows for easier configuration and troubleshooting.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27743 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now we can assume that every brcm47xx kernel has the bcma module build
into the kernel. This is not needed for this version as this does not
support bcma as system bus but kernel 3.0 will.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27733 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add new patches for bcm4716 SoC
* add support for serial flash on bcma bus
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27723 3c298f89-4303-0410-b956-a3cf2f4a3e73
