We dedicate 256MB for bootloader in GTA03 SD image, but actually they're
around 25KB currently. Reduce the stage2 pull to 32KByte.
Signed-off-by: Andy Green <andy@openmoko.com>
This patch changes Qi to insist to fetch device-specific kernels from
filesystems that have named kernels. The kernels looked for are now
called
GTA01: /boot/uImage-GTA01.bin
GTA02: /boot/uImage-GTA02.bin
GTA03: /boot/uImage-GTA03.bin
This is part of the support for single rootfs that can be run on
multiple devices with correct kernel and module handling by the
bootloader.
Signed-off-by: Andy Green <andy@openmoko.com>
The hack to find the number of sectors turns out to be
sensitive to the host kernel. This is a workaround until
we find something in /proc or /sys that has the same info
in a more accessible way.
Signed-off-by: Christopher Hall <hsw@openmoko.com>
The first revision for GTA03 A1 is "1", but we only populated
the info for revision 0.
Reported-by: Christopher Hall <hsw@openmoko.org>
Signed-off-by: Andy Green <andy@openmoko.com>
We don't have card detect connected. Try to fake it better by
enabling the peripheral fuction to the ball and forcing pulldown
(card detect is active-low).
Signed-off-by: Andy Green <andy@openmoko.com>
Prefer GTA03, enable dual mDDR init (killing SMDK compatability for now)
fix bugs in GPIO register offsets, set loglevel=8 for GTA03
Signed-off-by: Andy Green <andy@openmoko.com>
This gives compatability with SD Cards using the old U-Boot scheme of an initial
VFAT part for kernel and then ext2. If you put the kernel you actually want to
use in /boot/uImage.bin in the ext2 partition, it can boot these cards then.
Signed-off-by: Andy Green <andy@openmoko.com>
This makes a new behaviour for Qi, when there are no valid kernels then it
performs the memory test. It means you can either move kernels out of the way
to get the memory test, or make an SD Card just with normal Qi on it and no
kernels to get a memory test.
Signed-off-by: Andy Green <andy@openmoko.com>
Some of utils.c isn't used until the full Qi image has been loaded into
memory, to save space in 4K steppingstone case on 2442, we split utils.c now
so only the interesting routines for steppingstone time take up space there.
Signed-off-by: Andy Green <andy@openmoko.com>
We need putc even when we are operating entirely from steppingstone.
Arrange that the board-specific putc code is in a section that goes into
steppingstone, and adapt the utils.c putc() so that it no longer needs to
indirect through the board_api struct that is in main memory.
Signed-off-by: Andy Green <andy@openmoko.com>
This adds the memory testing code to Qi. It tests the range of memory with
several constants and then a 32-bit walking 1 pattern, and repeats forever.
The entire main SDRAM can be tested due to the fact this runs out of
steppingstone only and does not need to store anything outside of it.
It introduces a steppingstone-based stack for use entirely in steppingstone.
Signed-off-by: Andy Green <andy@openmoko.com>
Improve glamo-mmc so that it uses MMC_READ_MULTIPLE_BLOCK and copes with
64 blocks in one command (and STOP sent after each set), instead of sending
a new command per-block
Signed-off-by: Andy Green <andy@openmoko.com>
Little cleanup and new code that collects and defers contiguous sector reads
into one potentially more efficient larger sequential read action.
This matters for example on SD Card protocol.
Signed-off-by: Andy Green <andy@openmoko.com>
Naughty bug bug U-Boot ext2 implementation -- cut and paste of stanza above for
indir1 check used for indir2 but not all the check was not updated.
This removes hundreds of repeated reads of same sector during kernel load.
Signed-off-by: Andy Green <andy@openmoko.com>
There was a bug about dealing with last ext2 sector of file
because we failed to return the number of sectors pulled
Signed-off-by: Andy Green <andy@openmoko.com>
This heavily adapts the Samsung U-Boot hs_mmc code and combines it with the
SD / SDHC startup code written for glamo-mci stuff that is known to work OK
with common SD and SDHC.
tla01 is changed to use the implementation.
Signed-off-by: Andy Green <andy@openmoko.com>
We want utils stuffs in steppingstone part, it's too expensive to have
CRC32 in there. Bust it out into its own file that appears only in
everything_else section in second bootloader stage.
Signed-off-by: Andy Green <andy@openmoko.com>
This patch adds a small script that knows how to partition, format and
prepare with a bootloader image an SD Card for usage with SD Card boot
on 6410.
You use it like this:
./6410-partition-sd.sh sde sdhc ./image/qi-s3c6410-andy_495294c60f2f1432
This will prepare your card with three partitions and put the bootloader
images at the end as required by 6410 iROM.
If you put anything on the fourth parameter, it skips the fdisk and the
formatting stages and just updates the bootloader.
Signed-off-by: Andy Green <andy@openmoko.com>
This patch makes qi source structure cpu-centric, and allows multiple CPUs
to be handled with the board definitions inside the CPU dirs.
You have to make a particular CPU version of Qi now, which you can do by
a shell command like this:
make clean ; make CPU=s3c2442 && make CPU=s3c6410
which gets you
$ ls -l image/
total 744
-rwxrwxr-x 1 agreen agreen 25372 2008-10-17 18:25 qi-s3c2442-andy_77c1fcdddc3e2cbf
-rw-rw-r-- 1 agreen agreen 237100 2008-10-17 18:25 qi-s3c2442-andy_77c1fcdddc3e2cbf.dis
-rw-rw-r-- 1 agreen agreen 25388 2008-10-17 18:25 qi-s3c2442-andy_77c1fcdddc3e2cbf.udfu
-rwxrwxr-x 1 agreen agreen 22736 2008-10-17 18:25 qi-s3c6410-andy_77c1fcdddc3e2cbf
-rw-rw-r-- 1 agreen agreen 216294 2008-10-17 18:25 qi-s3c6410-andy_77c1fcdddc3e2cbf.dis
-rw-rw-r-- 1 agreen agreen 22752 2008-10-17 18:25 qi-s3c6410-andy_77c1fcdddc3e2cbf.udfu
The 6410 support in there is enough to send a character "U" on the 6410 SMDK
Because the product naming is not defined, currently the device targeted for 6410
is called "TLA01"
Signed-off-by: Andy Green <andy@openmoko.com>
Before leaving for Linux, gratuitously clear down the totrst / timeout counter
to help stop us dying partway through boot on effective power-off.
In the case we have no battery or battery < ~3V, we still somehow need to do
more in kernel because it can switch itself off more than 8 seconds
after this point.
Signed-off-by: Andy Green <andy@openmoko.com>
Part of the effort to save power during booting so we can do it inside the
500mW budget from un-enumerated USB connection.
Signed-off-by: Andy Green <andy@openmoko.com>
On the last read, master must NAK, on intermediate reads it must ACK.
If you get this wrong, communication with device is screwed even in Linux.
Signed-off-by: Andy Green <andy@openmoko.com>
We need to set a few more things up in pcf50633 to get suspend and resume
to work -- without them suspend actually goes OFF. Take the opportunity
to optimize this init significantly.
Signed-off-by: Andy Green <andy@openmoko.com>
With large SDHC cards, the ext2/3 filesystem put on large partitions
by mkfs.ext2/3 is not how it used to be, it has a dynamic multiplier for
its block addressing. Without these changes, based on a patch by Ryan
Chen
http://lists.denx.de/pipermail/u-boot/2008-July/037786.html
we cannot parse large ext3 filesystem.
Signed-off-by: Andy Green <andy@openmoko.com>
Now cards larger than 4GB are normal, we can't use the byte addressing
internally any more for SDHC type card. This changes us to use block
(512 byte) addressing internally always.
Signed-off-by: Andy Green <andy@openmoko.com>
This patch performs the equivalent init actions to the SDHC slow
unitl first bulk patch in kernel, it allows us to work with large
SDHC cards which exceed Glamo timeout capability at 16MHz for first
access.
Signed-off-by: Andy Green <andy@openmoko.com>
This patch increases the timeout for card initializaton so it works with
8GB Sandisk uSDHC, and adds the size computation for SDHC as well.
Signed-off-by: Andy Green <andy@openmoko.com>
This is the script for gta03 load by openocd. We use the single qi
image for all purposes now so U-Boot lowlevel_foo style crap is dead.
We have to run the first part of init before copying qi image to
TEXT_BASE (0x33000000) because DRAM is not functional until then.
Fixed branchthrough at 0x8 is used as a place to hang the breakpoint.
Signed-off-by: Andy Green <andy@openmoko.com>
This adds capability to use single qi image for JTAG load action as well
as execution from NAND. It requires JTAG script to load the image at
0x0 and 0x33000000 addresses, then set data at 0x04 address to 0xffffffff.
This eliminates the lowlevel_foo stuff from U-Boot world.
Signed-off-by: Andy Green <andy@openmoko.com>
This adds ext2 support from U-Boot and stitches it into the
partition stuff. It also upgrades the board definitions so they
can define the path to look for in the ext2 filesystem being
mounted. I used /boot/uImage.bin because this is already in use
by the packaged kernel.
We now mount, open and pull the kernel from ext2 in phase2.c if
the kernel source defines it.
Signed-off-by: Andy Green <andy@openmoko.com>
We have to minimally support DOS partition scheme.
Partitions are counted from 1+ now, and 0 means no
partition table instead of -1.
Signed-off-by: Andy Green <andy@openmoko.com>
We leave a lot of funny clocks up in things like camera unit. This
pares it down to just what we use in Qi.
Signed-off-by: Andy Green <andy@openmoko.com>
Moves various .h into include from drivers
Gets glamo-mmc.h working so we can detect
card ID / Size if the card is plugged in.
Adds FAT / MMC kernel source entry for GTA02 that
is first before the NAND one. When it works it will
favour to boot off SD Card if a kernel is found there, but
right now we don't have a working filesystem parser and
partition handling hooked up.
Signed-off-by: Andy Green <andy@openmoko.com>
Move serial.c into drivers/serial-s3c24xx.c and qi-serial.h into include/serial-s3c24xx.h
making things a bit cleaner for being s3c24xx-specific. This needed a lot of meddling
additionally, ending up with a new puts() callback that belongs in the board structure
and removal of the debug uart member, since the puts() action was the only user.
Also change serial init API name and function to only fix to 115kbps and adapt to
PCLK.
Signed-off-by: Andy Green <andy@openmoko.com>
Introduce generic bitbang I2C system, and a s3c24xx-specific implementation of
it that knows which GPIO pins and how to control them.
The generic bitbang stuff exposes synchronous (ie, it will return when it is
done) and asynchronous read and write APIs, allowing the delay between bits to
be hidden in other slow, looping code if necessary.
Signed-off-by: Andy Green <andy@openmoko.com>
