Since there is only one user of bcm_tag.h left, we can safely move it
into the firmware-utils directory, replacing the symlink.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33655 3c298f89-4303-0410-b956-a3cf2f4a3e73
gpio_keys_polled needs to be loaded in preinit for buttons to work for
entering failsafe.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33653 3c298f89-4303-0410-b956-a3cf2f4a3e73
Several new features for newer boards:
- add additional UARTs present on some boards
- add additional LEDs present on some boards
- add HSS audio device codec present on some boards
- add support for GSC present on some boards
- add per model setup support for newer boards
- set FLASH window per-model for boards with larger FLASH
Some fixes:
- add IRQ mapping for additional PCI devices (USB Host)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33647 3c298f89-4303-0410-b956-a3cf2f4a3e73
roll all avila patches into a single patch (no code changes)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33646 3c298f89-4303-0410-b956-a3cf2f4a3e73
Several new features for newer boards:
- add irq mapping for additional devices
- add platform data for i2c bus to SFP modules
- add additional UARTs present on some boards
- increased R/W delay for expansion bus UARTs
- add additional LEDs present on some boards
- add GPIO exports and configuration
- add ENET switch config present on some boards
- add support for GSC present on some boards
- added per model setup support for newer boards
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33644 3c298f89-4303-0410-b956-a3cf2f4a3e73
roll all cambria patches into a single patch (no code changes)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33643 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is being done for general cleanup
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33642 3c298f89-4303-0410-b956-a3cf2f4a3e73
Before it was tried to initialize the deactivated PCIe core in client
mode, but this causes the SoC to hang. Just do not initialize it at all
and ignore the core it is not working and nothing is connected to it
when the specific bit is set in the boardflags.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33620 3c298f89-4303-0410-b956-a3cf2f4a3e73
The new version of the ALL0256N now got 8MB SPI NOR flash instead of 4MB.
In order to expose the whole amount of flash, add another image which contains
the corresponding GENERIC_8M mtdparts.
[juhosg: change suffix from '8m' to '8M']
Patch by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33614 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33601 3c298f89-4303-0410-b956-a3cf2f4a3e73
The chip common and the PCIe code are accessing the sprom struct which
is not filled when these cores are initialized. Fix this by adding an
early initialize and fill the sprom struct before accessing it in other
code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33600 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bcma based SoCs with a ieee80211 core on the SoC and an other
connected via PCIe or USB store the sprom for the SoC with a sb/1/
prefix. The SoC with just one wifi core do not use prefixes. The
BCM4706 do not use a prefix for the SoC part at all, because the prefix
is the path to the ieee80211 core and there is non on the BCM4706.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33597 3c298f89-4303-0410-b956-a3cf2f4a3e73
Resolves an issue where isochronouse USB would cause the driver to hang as
well as scheduling issues.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33579 3c298f89-4303-0410-b956-a3cf2f4a3e73
This feature was experimental in old kernels but
that flag has been removed in 2.6.36. Additionally,
the option is enabled by default since then.
See: http://www.spinics.net/lists/linux-usb/msg31993.html
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33574 3c298f89-4303-0410-b956-a3cf2f4a3e73
For cns3xxx SCU_CONFIGURATION always shows multipe cores but SCU_CPU_STATUS
shows which ones are active.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33566 3c298f89-4303-0410-b956-a3cf2f4a3e73
Sometimes the port 0 was the WAN port or there could be some device
where the port 0 is not wired to an actual Ethernet port. Now telnet in
failsafe will listen on all ports of the switch so user do not have to
search for the correct port any more. This change will make the switch
leak traffic between the WAN and the LAN port, but you should not use
failsafe while connected to a untrusted network.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33544 3c298f89-4303-0410-b956-a3cf2f4a3e73
With these images, it is possible to use the 'unused'
partition of the flash. The 'fat' images can be installed
with the sysupgrade command. When a 'fat' image is
installed from a regular one, the platform specific
sysupgrade script copies the calibration data to the
end of the flash. Likewise, when a regular image is
installed from the 'fat' version the sysupgrade script
copies the calibration data back to the original location.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33540 3c298f89-4303-0410-b956-a3cf2f4a3e73
When not removing support for the wait instruction, when ruining on the
BCM4706 SoC the system stops after msleep() without an exception. I
haven't seen this problem on the other Broadcom SoCs with a 74K CPU,
but in the Broadcom SDK it is deactivated for all CPUs of this type.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33496 3c298f89-4303-0410-b956-a3cf2f4a3e73
The package block-hotplug doesn't exist, removing reference to it.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33473 3c298f89-4303-0410-b956-a3cf2f4a3e73
It should be implemmented in a cleaner way.
This reverts the following commits:
[ar71xx] dir-825-b1: Fix wholeflash images
[ar71xx] dir825b1: Add image for DIR-825-B1 that uses the whole flash"
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33459 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will make the kernel crash on systems using qemu < 1.1.0. Until fixed
disable VPFv4 capability probing.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33458 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a patch to connect eth0.1 (lan) to the only
ethernet connector available.
D-Link DAP-1350 goes bricked with AA 12.09-beta.
This is because the current esw configuration for the
board connects eth0.2 (wan) to the *ONE and ONLY*
ethernet connector available, preventing initial access
to the board through 192.168.1.1 on eth0.1 after flashing,
effectively bricking the board.
There are things that should be done to make this board
really useful, but for AA 12.09, this one liner is
indispensable.
Signed of by Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33411 3c298f89-4303-0410-b956-a3cf2f4a3e73
Somehow detecting the RAM size in common/setup.c doesn't
work here, it always detects 64M and then crashes on devices
with less RAM.
Probably using MEMC_REG_SDRAM_CFG1 to know the RAM size is how
it could be, for now I use the mem=32M kernel parameter to get
stuff working.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33381 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.
[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33344 3c298f89-4303-0410-b956-a3cf2f4a3e73
use {read,write}l_relaxed instead of the plain __raw_{read,write}l variants.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33330 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add missing andmask to ramips_esw register read for recv_good value.
Without the mask, recv_bad leaks into the recv_good packet count.
Didn't notice the bug before since you don't usually get bad
packets, so I only saw it when I was playing with overlength packets
earlier...
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33322 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use doubletagging to disable ramips_esw vlan by default, it seems
more reliable.
Daniel Golle found an issue where sometimes (possibly only for
RT3352) the default vlan disable method (clearing en_vlan, untag,
doubletag and putting all ports into vlan 0) doesn't work and the
packets get sent out vlan-tagged with vlan 0.
Instead switch to using the doubletagging method (allow doubletagged
packets, put all ports into vlan 0 with untag enabled) by default.
Unless someone figures out a way to really globally disable vlan for
this switch, this seems like the best (most reliable) option.
I did some tests regarding maximum packet size and did not see any
difference between the two methods, both allow for slightly bigger packets
than the ramips_main.c ethernet driver (ping stops going through
above "ping -s 1472" (1514 bytes), on the switch packets are recv_good until
"ping -s 1490", or about 1532 bytes).
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33321 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows them to transparently communicate with an external VLAN switch.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33305 3c298f89-4303-0410-b956-a3cf2f4a3e73
Power down phy on disabled switch ports.
Haven't measured this myself yet, but according to this
http://www.8devices.com/community/viewtopic.php?f=6&t=156
it can save about 300mW of power.
[juhosg: fix checkpatch warning]
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33304 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for 8devices Carambola dev board.
The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33303 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename POC registers.
The current code uses POC1-POC3.
The datasheet uses:
POC1: Port Control 0
POC1: Port Control 1
POC2: Port Control 2
So the first POC1 is a typo that should have been POC0, rename the
registers to POC0-POC2 accordingly.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33302 3c298f89-4303-0410-b956-a3cf2f4a3e73
Stop handling VLAN setup in the kernel.
Removes the obsolete RT305X_ESW_VLAN_CONFIG_BYPASS option I added for
WL-351 and add some extra comments.
Also removes the en_vlan per-port flag that isn't very useful really, it now
is only controlled by the global enable_vlan flag.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33301 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add switch setup to uci network defaults.
The 'lan' attribute is used to decide into which vlan to put the
port.
Currently 'disable' is never set, but the intention is to use this
for devices like the 8devices Carambola, which only has two ports
hooked up to the SoC.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33300 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add swconfig support to ramips_esw.c
This patch adds swconfig support for ramips_esw:
Tested on both D-LINK DIR-300 B1 and Sitecom WL-351 (external
rtl8366rb on internal port 5).
I've made sure that in the enable_vlan=0 case it behaves like a dumb
switch, so external switches should work fine with vlans and
verified this on the WL-351.
The current state shown by swconfig is always read directly from HW
registers, new settings only show after 'swconfig dev rt305x set apply'.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33299 3c298f89-4303-0410-b956-a3cf2f4a3e73
Minor indentation cleanup.
Prepare for the main swconfig patch by cleaning up indentation a bit.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33298 3c298f89-4303-0410-b956-a3cf2f4a3e73
An improved LED support for Buffalo WZR-HP-AG300H.
There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.
[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33294 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit 4878806326 (r33251) introduced a
regression with board= kernel command line parameter incorrectly
initialised.
The faulty builds propogated to the snapshots download area. This makes
the device unbootable and TP-Link users have to attach the serial to
recover.
Here is the q&d way i used to identify MIPS boards that didn't have a
corresponding entry in the image/Makefile:
for i in `find ../files/arch/mips/ath79/ -type f -exec cat {} \; \
| sed -n '/MIPS_MACHINE/ { s/^[^"]*"\([^"]*\)".*$/\1/; p; }'`; do
grep -q ,$i, Makefile || echo $i;
done > missing-boards.new
Reported-by: Casper on IRC
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33274 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWRT runs in a eSATA sheevaplug like a charm. This patch just enables
CONFIG_MACH_ESATA_SHEEVAPLUG so the proper MACHINE_START definition
is compiled in.
Signed-off-by: Unai Uribarri <unaiur@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33266 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 'mtdparts=' prefix and the name of the flash device is missing.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33226 3c298f89-4303-0410-b956-a3cf2f4a3e73
For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33224 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TL-WDR3600 is identical to the TL-WDR4300 with the exception that is has
only two antennas.
[juhosg: remove the custom machine type, change the board name instead]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33219 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are some ifdefs missing so when only ssb or only bcma was
selected in the kernel config it did not build.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33209 3c298f89-4303-0410-b956-a3cf2f4a3e73
Generate image for the ALL0239-3G which can be flashed through the
chipset-vendor SDK based firmware's web-interface and bootloader.
The bootloader seems to ignore uImage checksum errors, but does complain about
them once the 0xDEADC0DE was replaced by an actual JFFS2 page.
I'm working on implementing fixtrx for uImage in the mtd package to solve this.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33206 3c298f89-4303-0410-b956-a3cf2f4a3e73
rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.
[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]
Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33205 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Creation of uImage for WNR854T only done once (before 2x for jffs2 build and 1x for squashfs build)
* Got rid of unneccessary padding of rootfs partition
* ARM zImages always need a machine id, therefore do not copy generic (=no id) uImage to BIN_DIR, instead copy zImage
* Generalized functions for easier re-using and enhancing (e.g. D-Link DNS 323 implementation would be only a couple lines)
* Copy rootfs partitions to BIN_DIR, just like it is done for D-Link DNS 323
* Use variables to allows easily changing for custom builds, e.g. kernel mtd size for symbols
* Size check of kernel files to avoid builds that break devices
* Use for "-sysupgrade" and "-factory" in image names (like ar71xx, brcm63xx, etc.) to avoid questions about which image to use
Signed-off by: Matthias Buecher <mail@maddes.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33174 3c298f89-4303-0410-b956-a3cf2f4a3e73
In order to get OHCI/EHCI working on the Rt3352, the platform device must be
named so rt3883-?hci will recognize it.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33145 3c298f89-4303-0410-b956-a3cf2f4a3e73
As the userspace has no means to determine the maximum possible timeout, use
that as the default and let the userspace lower it when necessary.
As the result the usual OpenWrt install (with busybox's watchdog trying to set
the timeout to 60s on start) is using a 33s timeout on an RT3052 clocked at
384MHz instead of the current 20s default.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33144 3c298f89-4303-0410-b956-a3cf2f4a3e73
D-Link's DIR-620 allows to flash a uImage directly from its web-interface but
for that the image name should be set to DIR_620.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33143 3c298f89-4303-0410-b956-a3cf2f4a3e73
Full functionality runtime tested, installation via OEM web-interface requires
a follow-up patch.
Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing
bits (including the antiparallel wps led).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33142 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes this section mismatch warning:
WARNING: vmlinux.o(.meminit.text+0xb14): Section mismatch in reference
from the function memblock_insert_region() to the function
.init.text:crashlog_init_memblock()
The function __meminit memblock_insert_region() references
a function __init crashlog_init_memblock().
If crashlog_init_memblock is only used by memblock_insert_region then
annotate crashlog_init_memblock with a matching annotation.
Also, remove the __init annotations from 'include/linux/crashlog.h'
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33137 3c298f89-4303-0410-b956-a3cf2f4a3e73
