This patch adds preliminary support for the Mikrotik RB2011L.
The NAND flash is not yet supported, so only the initramfs
kernel can be used for now.
[juhosg: remove unnecessary PCI/USB related stuff, the board
does not use that, update commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33344 3c298f89-4303-0410-b956-a3cf2f4a3e73
use {read,write}l_relaxed instead of the plain __raw_{read,write}l variants.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33330 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add missing andmask to ramips_esw register read for recv_good value.
Without the mask, recv_bad leaks into the recv_good packet count.
Didn't notice the bug before since you don't usually get bad
packets, so I only saw it when I was playing with overlength packets
earlier...
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33322 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use doubletagging to disable ramips_esw vlan by default, it seems
more reliable.
Daniel Golle found an issue where sometimes (possibly only for
RT3352) the default vlan disable method (clearing en_vlan, untag,
doubletag and putting all ports into vlan 0) doesn't work and the
packets get sent out vlan-tagged with vlan 0.
Instead switch to using the doubletagging method (allow doubletagged
packets, put all ports into vlan 0 with untag enabled) by default.
Unless someone figures out a way to really globally disable vlan for
this switch, this seems like the best (most reliable) option.
I did some tests regarding maximum packet size and did not see any
difference between the two methods, both allow for slightly bigger packets
than the ramips_main.c ethernet driver (ping stops going through
above "ping -s 1472" (1514 bytes), on the switch packets are recv_good until
"ping -s 1490", or about 1532 bytes).
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33321 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows them to transparently communicate with an external VLAN switch.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33305 3c298f89-4303-0410-b956-a3cf2f4a3e73
Power down phy on disabled switch ports.
Haven't measured this myself yet, but according to this
http://www.8devices.com/community/viewtopic.php?f=6&t=156
it can save about 300mW of power.
[juhosg: fix checkpatch warning]
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33304 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for 8devices Carambola dev board.
The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33303 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename POC registers.
The current code uses POC1-POC3.
The datasheet uses:
POC1: Port Control 0
POC1: Port Control 1
POC2: Port Control 2
So the first POC1 is a typo that should have been POC0, rename the
registers to POC0-POC2 accordingly.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33302 3c298f89-4303-0410-b956-a3cf2f4a3e73
Stop handling VLAN setup in the kernel.
Removes the obsolete RT305X_ESW_VLAN_CONFIG_BYPASS option I added for
WL-351 and add some extra comments.
Also removes the en_vlan per-port flag that isn't very useful really, it now
is only controlled by the global enable_vlan flag.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33301 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add switch setup to uci network defaults.
The 'lan' attribute is used to decide into which vlan to put the
port.
Currently 'disable' is never set, but the intention is to use this
for devices like the 8devices Carambola, which only has two ports
hooked up to the SoC.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33300 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add swconfig support to ramips_esw.c
This patch adds swconfig support for ramips_esw:
Tested on both D-LINK DIR-300 B1 and Sitecom WL-351 (external
rtl8366rb on internal port 5).
I've made sure that in the enable_vlan=0 case it behaves like a dumb
switch, so external switches should work fine with vlans and
verified this on the WL-351.
The current state shown by swconfig is always read directly from HW
registers, new settings only show after 'swconfig dev rt305x set apply'.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33299 3c298f89-4303-0410-b956-a3cf2f4a3e73
Minor indentation cleanup.
Prepare for the main swconfig patch by cleaning up indentation a bit.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33298 3c298f89-4303-0410-b956-a3cf2f4a3e73
An improved LED support for Buffalo WZR-HP-AG300H.
There will be two new packages to go with this patch
(ar922x-led-fix-hotplug and ar922x-led-fix-init).
These packages essentially perform the same task of
disabling "JTAG over GPIO pins" function which is
currently required for LEDs on AR922x emac GPIO to work,
and are both considered a temporary fix that circumvent
this problem.
[juhosg: add the hotplug script from the proposed
ar922x-led-fix-hotplug package to ar71xx/base-files]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33294 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit 4878806326 (r33251) introduced a
regression with board= kernel command line parameter incorrectly
initialised.
The faulty builds propogated to the snapshots download area. This makes
the device unbootable and TP-Link users have to attach the serial to
recover.
Here is the q&d way i used to identify MIPS boards that didn't have a
corresponding entry in the image/Makefile:
for i in `find ../files/arch/mips/ath79/ -type f -exec cat {} \; \
| sed -n '/MIPS_MACHINE/ { s/^[^"]*"\([^"]*\)".*$/\1/; p; }'`; do
grep -q ,$i, Makefile || echo $i;
done > missing-boards.new
Reported-by: Casper on IRC
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33274 3c298f89-4303-0410-b956-a3cf2f4a3e73
OpenWRT runs in a eSATA sheevaplug like a charm. This patch just enables
CONFIG_MACH_ESATA_SHEEVAPLUG so the proper MACHINE_START definition
is compiled in.
Signed-off-by: Unai Uribarri <unaiur@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33266 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 'mtdparts=' prefix and the name of the flash device is missing.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33226 3c298f89-4303-0410-b956-a3cf2f4a3e73
For the pure convenience of having a correctly named
image and system name in /proc/cpuinfo , until we can
do that by having system names in DTS...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33224 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TL-WDR3600 is identical to the TL-WDR4300 with the exception that is has
only two antennas.
[juhosg: remove the custom machine type, change the board name instead]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33219 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are some ifdefs missing so when only ssb or only bcma was
selected in the kernel config it did not build.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33209 3c298f89-4303-0410-b956-a3cf2f4a3e73
Generate image for the ALL0239-3G which can be flashed through the
chipset-vendor SDK based firmware's web-interface and bootloader.
The bootloader seems to ignore uImage checksum errors, but does complain about
them once the 0xDEADC0DE was replaced by an actual JFFS2 page.
I'm working on implementing fixtrx for uImage in the mtd package to solve this.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33206 3c298f89-4303-0410-b956-a3cf2f4a3e73
rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.
[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]
Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33205 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Creation of uImage for WNR854T only done once (before 2x for jffs2 build and 1x for squashfs build)
* Got rid of unneccessary padding of rootfs partition
* ARM zImages always need a machine id, therefore do not copy generic (=no id) uImage to BIN_DIR, instead copy zImage
* Generalized functions for easier re-using and enhancing (e.g. D-Link DNS 323 implementation would be only a couple lines)
* Copy rootfs partitions to BIN_DIR, just like it is done for D-Link DNS 323
* Use variables to allows easily changing for custom builds, e.g. kernel mtd size for symbols
* Size check of kernel files to avoid builds that break devices
* Use for "-sysupgrade" and "-factory" in image names (like ar71xx, brcm63xx, etc.) to avoid questions about which image to use
Signed-off by: Matthias Buecher <mail@maddes.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33174 3c298f89-4303-0410-b956-a3cf2f4a3e73
In order to get OHCI/EHCI working on the Rt3352, the platform device must be
named so rt3883-?hci will recognize it.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33145 3c298f89-4303-0410-b956-a3cf2f4a3e73
As the userspace has no means to determine the maximum possible timeout, use
that as the default and let the userspace lower it when necessary.
As the result the usual OpenWrt install (with busybox's watchdog trying to set
the timeout to 60s on start) is using a 33s timeout on an RT3052 clocked at
384MHz instead of the current 20s default.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33144 3c298f89-4303-0410-b956-a3cf2f4a3e73
D-Link's DIR-620 allows to flash a uImage directly from its web-interface but
for that the image name should be set to DIR_620.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33143 3c298f89-4303-0410-b956-a3cf2f4a3e73
Full functionality runtime tested, installation via OEM web-interface requires
a follow-up patch.
Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing
bits (including the antiparallel wps led).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33142 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes this section mismatch warning:
WARNING: vmlinux.o(.meminit.text+0xb14): Section mismatch in reference
from the function memblock_insert_region() to the function
.init.text:crashlog_init_memblock()
The function __meminit memblock_insert_region() references
a function __init crashlog_init_memblock().
If crashlog_init_memblock is only used by memblock_insert_region then
annotate crashlog_init_memblock with a matching annotation.
Also, remove the __init annotations from 'include/linux/crashlog.h'
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33137 3c298f89-4303-0410-b956-a3cf2f4a3e73
The following patch corrects a hard reset that occurs on alix and
soekris net5501 hardware. Specifically, this is an issue with the via
rhine NIC driver. Under periods of extreme load, the via rhine driver
can cause a reset of the entire system. When this happens no output is
seen on the console, the device simply reboots. This was reported in the
following ticket:
Consistent crash on Soekris NET5501
https://dev.openwrt.org/ticket/11882
I was able to reproduce the problem locally with numerous alix 2d13
platforms. Under heavy 64 byte frame size load from a Smartbits traffic
generator, the alix hardware will hard reset in under 5 minutes. The
same hardware, under the same load, on FreeBSD 9.0 does not reset.
The patch below backports most of the via rhine changes from kernel 3.5.
With OpenWrt trunk being on kernel 3.3.8, it seemed prudent to bring
these changes in to avoid this serious issue.
I've tested this heavily in my test environment and was able to keep the
device stable under load for extended periods of time without any resets.
Also, a nice side effect of this change is that it significantly raises
the performance the platform. Without this patch the alix 2d13 can move
approximately 29,000 packets per second at 64 byte frame sizes. After
this patch the alix can move 52,000 packets per second at 64 byte frame
sizes.
I put this patch under the x86 patches as those are the only platforms
with via rhine hardware that I'm aware of. If it needs to go some place
else please let me know.
Thanks,
Adam
Signed-off-by: Adam Gensler <openwrt@kristenandadam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33072 3c298f89-4303-0410-b956-a3cf2f4a3e73
The kernel has to be rounded up to the nearest 1MB, then we append
the root filesystem at its end.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33066 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the GPIO ALTSEL settings for some of the GPIOs used by the PCI subsystem in Lantiq Danube. These changes are required for more than one PCI device to work. Tested with an ARV7510PW having two PCI-devices; a VIA USB controller and a Ralink WLAN mini-PCI card.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@33054 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ARV4525 board init is passing the wrong offset to
arv_register_ath5k() resulting in a bogus mac.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32993 3c298f89-4303-0410-b956-a3cf2f4a3e73
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
Brought over from 3.5-stable
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32950 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used to start/stop the switch if that is
supported by the given board.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32943 3c298f89-4303-0410-b956-a3cf2f4a3e73
Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32932 3c298f89-4303-0410-b956-a3cf2f4a3e73
The patch set for Buffalo WLAE-AG300N initial support.
There is another patch for wireless led support that
is posted separately.
Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.
[juhosg: fix coding style]
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32931 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is currently badly broken on ARM, until fixed, disable it
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32926 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32924 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update enetswith driver with latest fixes and additions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32921 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the order and names of patches.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32920 3c298f89-4303-0410-b956-a3cf2f4a3e73
Attached patch fixes a typo in the image Makefile, and overrides the
board name for DVA-G3810BN to set the correct board properties
Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32894 3c298f89-4303-0410-b956-a3cf2f4a3e73
atheros trunk moved to full sysfs gpiolib, but the leds were forgotten.
This restores the wlan led that was missing after switching from backfire
to trunk.
Signed-off-by: Karl Palsson <karlp@remake.is>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32885 3c298f89-4303-0410-b956-a3cf2f4a3e73
I did not add the last patch, because it add some stubs for the flash drivers and our patches have to be changed for that, if the flash support in bcma is able to do something I will integrate it.
This also contains 3 additional patches fixing some bugs in bcma.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32880 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes a small typo in kmod-leds-wndr3700-usb description, where the board is for some reason made by NETGWR, not NETGEAR.
Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32870 3c298f89-4303-0410-b956-a3cf2f4a3e73
Increase the size of the buffer used for eeprom reads during the platform configuration of the Gateworks laguna. The model name read in is 16 bytes but the original buffer was only 8 bytes.
Signed-off-by: David Acker <dacker@rajant.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32833 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for Raspberry Pi / brcm2708 / 2835
Signed-off-by: Ian Ridge <ianridge [at] gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32825 3c298f89-4303-0410-b956-a3cf2f4a3e73
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32821 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for revision D of the MI424WR.
Rev D swaps LAN & WAN ports so this patch maintains
eth0 for LAN and eth1 for WAN. For details on rev D usage,
see http://wiki.openwrt.org/toh/actiontec/mi424wr
Signed-off-by: Jose Vasconcellos <jvasco@verizon.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32820 3c298f89-4303-0410-b956-a3cf2f4a3e73
Setup initial configuration for Wifi and USB LEDS of a Fonera 2.0n (ramips)
Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32819 3c298f89-4303-0410-b956-a3cf2f4a3e73
detect EEPROM, MAC addresses and support sysupgrade for the ALL5002
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32816 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hope that this works, didn't have a chance to actually test it...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32815 3c298f89-4303-0410-b956-a3cf2f4a3e73
support ALL5002 in ramips/rt305x branch of the kernel.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32813 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently, sys_clk/10 is used which is just wrong.
cpu_clk/10 would work for systems with 400MHz CPU clock.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32812 3c298f89-4303-0410-b956-a3cf2f4a3e73
The following patch is necessary for the InternetBox (Surfbox) board-specific
idsel to work with newer kernels. Acutally I don't exactly understand why this
was not necessary before, but without the udelay, the MiniPCI adapter in slot 3
is not detected and set up correctly.
Also remove platform broken flag, it works.
Signed-off-by: Bruno Randolf <br1@einfach.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32766 3c298f89-4303-0410-b956-a3cf2f4a3e73
