This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30434 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be usable only from linux-3.3.
Based on a patch by Dave Taht <dave.taht@bufferbloat.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30417 3c298f89-4303-0410-b956-a3cf2f4a3e73
List of patches that Jo-Philipp groveled out of git.
Redux: defuzzed.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30366 3c298f89-4303-0410-b956-a3cf2f4a3e73
Clone of CFLAGS change from r30013 into Geos and Alix platforms.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30353 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch from Philip Prindeville.
While at it, also refresh the patches.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30025 3c298f89-4303-0410-b956-a3cf2f4a3e73
So that builds don't stall in x86 prompting for this symbol.
[From Philip Prindeville, via http://patchwork.openwrt.org/patch/1828/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30023 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Geos driver is in linux-next and will be out in 3.4. It builds fine against 3.2.2 and 3.3-rc2.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30022 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport net5501 platform driver from 3.4.
Remove vestiges of old (pre-2.6.30) leds-net5501.c driver.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30021 3c298f89-4303-0410-b956-a3cf2f4a3e73
These should only be enabled in the generic image, as they bloat all of the other targets.
Also add symbols for NET5501, ALIX, and GEOS which were added backported to 3.2 and 3.3.
Restore PC speaker to Geos target.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30019 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patches the CFLAGS for Geode LX CPUs for 4.3 and new GGC versions. This creates more compatible code and allowed me to boot my system first time with no troubles. Also, the missing kmod is added in.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30013 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add patches to x86/patches-3.2 and x86/patches-3.3 (update will appear in 3.4).
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1817/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30001 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove packages which are dependencies of other packages
Remove packages which are part of the default package list
Remove DSL specific packages from net5501
Remove bridge package, we use the busybox applet
Replace hostapd with wpad
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29999 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport of linux-next driver.
Driver adds support for LEDS and S/W button.
Add hotplug script for button actions.
Add Openwrt system config for LEDS triggers.
Add updated kernel .config for 3.2 symbols.
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1816/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29996 3c298f89-4303-0410-b956-a3cf2f4a3e73
In 3.1, the old drivers/char/ entry for the CS5535 GPIO driver went obsolete.
Make Geos use a recent kernel and remove this ambiguity.
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1815/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29995 3c298f89-4303-0410-b956-a3cf2f4a3e73
Bump to version 3.2.
Simplify and correct kernel config (based on x86/config-3.2).
Designate eth0 as wan interface, and bridge eth1/eth2/eth3.
Add heartbeat LED trigger.
Use correct CS5535 GPIO driver.
Use correct USB drivers (OHCI not UHCI).
Add MSR and HW clock support.
Add GPIO mask definition.
Add correct SATA drivers.
Add LED triggers.
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1802/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29994 3c298f89-4303-0410-b956-a3cf2f4a3e73
Bump to version 3.2.
Simplify and correct kernel config (based on x86/config-3.2).
Drop obsolete CS5535 GPIO driver.
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1804/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29981 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for D-LINK DIR-615 E4 board. It's mostly based
on the existing support for DIR-600 A1, with some changes in the leds
configuration.
It's an updated version of the patch that reliably works on my hw for
about a year (it was built from trunk on Jan 2011). When I decided to
update the firmware and checked for the current support for that device,
I also found previously posted patches by Alexey Loukianov that
mentioned some stability issues. I'm not sure where could be the
difference, the patches are very similar except the wmac led pin number
- I was using 1, and those patches used 17.
[juhosg: add 3.2 support]
Signed-off-by: Vadim Girlin <vadimgirlin@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29973 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adds support for TL-MR11U, a portable router with very similar
hardware to the TL-WR703N and TL-MR3020, but with an onboard
2000mAh battery.
Tested, working:
All interfaces (Ethernet, 802.11n, USB)
WPS & Reset switches (Power appears to be a hardware slider)
Ethernet, Wifi, 3G LEDs (Power & charging LEDs hardware controlled)
Sysupgrade
[juhosg: fix indentations to use TABs instead of spaces, fix 3.2 patch
breakage]
Signed-off-by: Simon Taylor <simon.taylor.uk@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29972 3c298f89-4303-0410-b956-a3cf2f4a3e73
These devices have two devices on the bus, the host controller itself and the device.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29923 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: remove ath9k from the the profile package list, build WPE72
image with the Default profile as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29914 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Compex WPE72 bare board and Compex WPE72NX
Indoor Access Point.
[juhosg: add support to 3.2 as well]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29912 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29910 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the board detection of the TL-MR3020.
The LED behaviour has also been modified:
* The WPS LED is the diag LED now.
* A netdev trigger for the LAN LED has been added.
The profile of the TL-MR3020 has been updated because the needed package
"kmod-ledtrig-usbdev" was missing which resulted in a non-working usbdev
trigger for the 3G/USB LED.
[juhosg: the board name changes has been removed, and the kernel files
has been changed instead.]
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29905 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the GPIO polarity for the button and the sliding
switch. The buttons are not active low. "Pressed" and "Released"
events are wrong without the patch.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29904 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds uci-defaults and sysupgrade support for the ALL0256N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29883 3c298f89-4303-0410-b956-a3cf2f4a3e73
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29871 3c298f89-4303-0410-b956-a3cf2f4a3e73
After issuing a soft reset on the RT8366{S,RB}
switch, waiting for the last acknowlegement fails
in rtl8366_smi_write_reg. Add a _noack version of
the function and use that for issuing a soft reset.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29844 3c298f89-4303-0410-b956-a3cf2f4a3e73
This also adds minimal support for the BCMA43224 pcie wireless card.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29843 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch add sysupgrade for Engenius ESR-9753
Signed-off-by: Artur Wronowski <arteqw@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29824 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add skb_frag_page from 3.2 to OCF for 3.1 and earlier and use it.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29818 3c298f89-4303-0410-b956-a3cf2f4a3e73
The following symbols are missing for x86, in sorted order.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29783 3c298f89-4303-0410-b956-a3cf2f4a3e73
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29763 3c298f89-4303-0410-b956-a3cf2f4a3e73
Previously the tx housekeeping was done in a spin_lock_irqsave critical
section which causes irqs to be disabled during that time. Since the
housekeeping is already prepared to be scheduled as a tasklet process
the housekeeping only in softirq context and revise the locking between
the tx path and the housekeeping tasklet by using a normal spin_lock
which in most situations will be a NOP anyway.
This makes sure that interrupts are only disabled for a short time
since in the worst case the housekeeping might have to free up to 256
skbs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29762 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add workarround for BCM5357 and BCM4749.
This patch contains the following fixes from George Kashperko:
* separate subroutines for controller initialization workarounds -
following CodingStyle recommendations;
* __devinit __devexit __devinitconst annotations for CONFIG_HOTPLUG;
* fix leak in ssb_hcd_create_pdev/bcma_hcd_create_pdev - as hci_res being
kmalloc'ed is never freed anywhere while platform_device_add_resources
will kmemdup resources right away;
* fix compilation error in ssb_hcd_resume - it will fail as soon as
CONFIG_PM is selected.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29734 3c298f89-4303-0410-b956-a3cf2f4a3e73
Should fix whiteout issues and missing files when using extroot.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29727 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reading from the flash chip on the TL-WR2543ND seems buggy.
If the SPI flash driver tries to read too much data in one
SPI transfer, the flash chip returns bogus values. This can
be caused by a buggy flash chip on my board, or it can
be a bug in our SPI driver.
Add a workaround to the m25p80 driver until I find out the
root cause of the problem. The patch allows to specify the
maximum numner of bytes which can be read safely withint
one SPI transfer.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29679 3c298f89-4303-0410-b956-a3cf2f4a3e73
* make clock delay configurable
* make read,write commands configurable
* use u16 for member and untag fields
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29677 3c298f89-4303-0410-b956-a3cf2f4a3e73
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29675 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is based on patches from the linux-longsoon-community git tree:
http://dev.lemote.com/cgit/linux-loongson-community.git/
Now the kernel can use the command line parameter from kexec-tools.
Runtime tested on ar71xx with 2.6.39.4 (the wathdog must be stopped
before executing the new kernel). Compile tested with lantiq (3.1.4)
and brcm47xx (3.0.12).
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29674 3c298f89-4303-0410-b956-a3cf2f4a3e73
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29662 3c298f89-4303-0410-b956-a3cf2f4a3e73
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29658 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29651 3c298f89-4303-0410-b956-a3cf2f4a3e73
commit 8efa88540635 (sch_sfq: avoid giving spurious NET_XMIT_CN signals)
forgot to call qdisc_tree_decrease_qlen() to signal upper levels that a
packet (from another flow) was dropped, leading to various problems.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29642 3c298f89-4303-0410-b956-a3cf2f4a3e73
Works for me! ;-)
Patch-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29614 3c298f89-4303-0410-b956-a3cf2f4a3e73
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29604 3c298f89-4303-0410-b956-a3cf2f4a3e73
This new usb driver uses an extra device so the ehci and the ohci driver are not depending on ech other any more.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29575 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are problems with the patches for kernel 2.6.39 and I do not want to support two different sets of patches.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29573 3c298f89-4303-0410-b956-a3cf2f4a3e73
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29557 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29533 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the issues with the jffs2 images on various boards. Using
JFFS2 on devices with 4KiB erase sectors is not safe:
http://lists.infradead.org/pipermail/linux-mtd/2011-June/036591.html
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29521 3c298f89-4303-0410-b956-a3cf2f4a3e73
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29513 3c298f89-4303-0410-b956-a3cf2f4a3e73
Factory images for WNDR3700v2 and WNDR3800 should contain these model IDs
for the device: field in their DNI tags, not WNDR3700.
This regressed in r29434, which redid WNDR3x00 model detection. The sixth
parameter to Image/Build/Netgear is only used as the -B argument to
mkdniimg, which is used to set the device: field. In r29434, this was
erroneously changed to be WNDR3700 for all models. The tools to flash
factory images (U-Boot's TFTP server and the factory software's upgrade
utility) may refuse to honor images with incorrect device: fields in their
DNI tags.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29473 3c298f89-4303-0410-b956-a3cf2f4a3e73
Detect the model name for /tmp/sysinfo/model based on 10 bytes at offset
56 in the art (caldata) mtd partition.
r29434 redid WNDR3x00 model detection, attempting to distinguish between
WNDR3700v2 and WNDR3800 by checking MemTotal in /proc/meminfo. However, it
contained a bug: it put the awk inside a $(...), with the result that all
WNDR3700v2 and WNDR3800 models would be reported as WNDR3800. This patch
checks the model name stored in the art partition, as is done by U-Boot
shipping on the WNDR3800. It has the likely advantage of working with
future models based on the WNDR3700 board. It also will not mis-detect
units on which people install more memory.
I have tested this patch on WNDR3700 (v1), WNDR3700v2, and WNDR3800.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29472 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch by Cristian Deluxe <djcristiandeluxe@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29468 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch by Nerijus Baliunas <nerijus@users.sourceforge.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29454 3c298f89-4303-0410-b956-a3cf2f4a3e73
With the default OpenWrt configuration, this increases the size
of the rootfs_data partition by 384KB/128KB on the older/newer
TP-Link models.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29447 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: the name of the final image has been changed to
'openwrt-ar71xx-generic-om2p-squashfs-factory.bin']
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29397 3c298f89-4303-0410-b956-a3cf2f4a3e73
