There's not enough time between Glamo init (now after pcf50633 init)
and the completion of machine init before we try to use the boot device
in the case of GTA02 and SD boot. So we add rootdelay=1 to the SD
card boot cases
Signed-off-by: Andy Green <andy@openmoko.com>
This patch effectively doubles maximum time allowed for retries performed by
mmc_init. Also, the delay was shortened to lower the average time needed to
init a card. Without it, i was unable to boot from Transcend TS8GUSDHC4
(appending rootdelay=1 was necessary as well).
Change to input / pulldown on most GPIO. With no battery and just
USB power, this gets us into suspend with 9.5mA at 5V consumption... but
Ben Dooks told that we don't put the mDDR into deep sleep yet in the
platform pm code, so this should come right down when we have that.
The suspend is otherwise real though, PWREN to the PMU goes down, and
when we wake the device Qi is able to see it is a resume wake and jumps
back into Linux, where we currently die due to issues on s3c6410 platform
code getting worked on.
Signed-off-by: Andy Green <andy@openmoko.com>
Make sure WLAN module power is off by default - this controls
a P-Channel MOSFET that gates all the power there
Signed-off-by: Andy Green <andy@openmoko.com>
First go at resume processing for 6410, can't test it until Ben Dooks
confirms operation of Linux side on SMDK
Signed-off-by: Andy Green <andy@openmoko.com>
This patch turns on the SYS and BAT monitoring filters, and checks if the battery
meets the BAT OK threshold. If it doesn't, which is the case if the battery is
not present, it disables the "indicator" (eg, LED, vibrator) stuff and holds the
CPU at 200MHz during the boot into Linux.
This allows the GTA02 A6 here to boot with no battery up to the point it is
going to bring up backlight, and this with 100mA limit on USB at PMU. Enabling
the threshold filters for battery and SYS seems to have been critical in
getting any stability with this.
Signed-off-by: Andy Green <andy@openmoko.com>
tty0 is the LCM... this patch changes the defaults so that the kernel
always treats tty0 as a console, but it also sets the loglevel so that
only KERN_ERR or worse will be printed there. With matching changes
to the kernel, most of the noise at KERN_ERR is reduced to KERN_INFO,
so it gets the behviour the LCM by default is not cluttered with
messages unless they are important during boot.
Signed-off-by: Andy Green <andy@openmoko.com>
Allow a board to "indicate" events if it likes on whatever it has
On GTA02 we light AUX during boot and run the vibrator briefly when we
skip a partition or device.
Signed-off-by: Andy Green <andy@openmoko.com>
Despite what the docs say, steppingstone is always resident at
0x40000000 on s3c2442, this patch changes our linker script to
stick all steppingstone code there. The mapping of steppingstone
at 0x0 is broken by OM[] bus change dynamically caused for example
by GTA02 AUX button actuation.
Signed-off-by: Andy Green <andy@openmoko.com>
Recent addition of append and noboot file checks broke NAND
Reported-by: Micael Henriksson <micael.h@gmail.com>
Signed-off-by: Andy Green <andy@openmoko.com>
This adds two features that can be set in the rootfs that Qi is checking.
- if it finds /boot/noboot-<device>, eg /boot/noboot-GTA02 then it will
skip the rootfs for booting and try the next one if any
- if it finds /boot/append-<device>, eg, /boot/append-GTA02 then it will
append the contents of this file to the kernel commandline.
Signed-off-by: Andy Green <andy@openmoko.com>
We dedicate 256MB for bootloader in GTA03 SD image, but actually they're
around 25KB currently. Reduce the stage2 pull to 32KByte.
Signed-off-by: Andy Green <andy@openmoko.com>
This patch changes Qi to insist to fetch device-specific kernels from
filesystems that have named kernels. The kernels looked for are now
called
GTA01: /boot/uImage-GTA01.bin
GTA02: /boot/uImage-GTA02.bin
GTA03: /boot/uImage-GTA03.bin
This is part of the support for single rootfs that can be run on
multiple devices with correct kernel and module handling by the
bootloader.
Signed-off-by: Andy Green <andy@openmoko.com>
The hack to find the number of sectors turns out to be
sensitive to the host kernel. This is a workaround until
we find something in /proc or /sys that has the same info
in a more accessible way.
Signed-off-by: Christopher Hall <hsw@openmoko.com>
The first revision for GTA03 A1 is "1", but we only populated
the info for revision 0.
Reported-by: Christopher Hall <hsw@openmoko.org>
Signed-off-by: Andy Green <andy@openmoko.com>
We don't have card detect connected. Try to fake it better by
enabling the peripheral fuction to the ball and forcing pulldown
(card detect is active-low).
Signed-off-by: Andy Green <andy@openmoko.com>
